Ours doesn't work at all it shows the wrong compass heading and gradually
steers further and further off course until we're doing doughnuts. I've
been wondering what to do with it.
Jessica
On Saturday, September 10, 2016, dwight veinot via CnC-List <
cnc-list@cnc-list.com> wrote:
> It won't work
It won't work well unless you have the rudder angle sensor installed I
tried to avoid getting down below to install that rudder angle sensor and
the unit just didn't work right until I spent many hours in a cramped space
and got it done been fine ever since. Also check the connections from the
flux
Check the belt in the housing that is attached to the wheel. You have to remove
the housing from the wheel and pry it open. Chances are, by your description,
that the belt is worn and slipping.
Replacement belts can be found online. Make sure you get the right one.
Raymarine made a black housin
HI Ted: I’ll take it……….I’ll send my info to you offline. Thanks, Ron
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Ted Drossos
via CnC-List
Sent: Tuesday, January 12, 2016 1:23 AM
To: cnc-list@cnc-list.com
Cc: Ted Drossos
Subject: Stus-List Autohelm hand bearing compa
I just had Raymarine re-build my linear drive for $650. A bargain in my
opinion.
David F. Risch
1981 40-2
(401) 419-4650 (cell)
Date: Sun, 7 Jun 2015 12:18:40 -0500
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm problem
From: cnc-list@cnc-list.com
CC: f...@postaudio.net
Steve — do
Steve — do you have a linear electric drive? If so, it sounds like the gearing
has finally worn out. You can replace with another linear Type 1 drive; or if
your course computer will handle the current, replace with a hydraulic drive
like the Octopus drive. Feel free to contact me off-list to
My hydraulic drive leaked enough fluid to no longer function. Filled it
and everything was back to normal.
Josh Muckley
S/V Sea Hawk
1989 C&C 37+
Solomons, MD
On Jun 7, 2015 9:46 AM, "OldSteveh via CnC-List"
wrote:
> My trusty under deck autohelm malfunctioned yesterday.
> loud motor noise from
Fell ; cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm
Peter:
I wasn’t aware Raymarine had gone to permanently mounted tillerpilots. Not an
improvement, in my opinion. I imagine they would be in the way, as well as
exposed to weather. I also wonder how easy they would be to steal.
Jack
t;
>
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Jack
> Brennan via CnC-List
> *Sent:* Tuesday, March 03, 2015 11:51 AM
> *To:* Peter Fell; cnc-list@cnc-list.com
> *Subject:* Re: Stus-List Autohelm
>
>
>
> Peter:
>
>
>
> I w
drive unit below decks and out of the weather.
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jack Brennan
via CnC-List
Sent: Tuesday, March 03, 2015 11:51 AM
To: Peter Fell; cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm
Peter:
I wasn’t aware Raymarine had
erde, Fl.
From: Peter Fell via CnC-List
Sent: Tuesday, March 03, 2015 11:23 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm
Jack
I think you probably mean ST1000 ... and it has a displacement rating of 6,600
lbs. The ST2000 does 10,000 lbs. The Evolution units (as per the older S
Sent: Tuesday, March 03, 2015 8:03 AM
To: Burt Stratton ; cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm
Burt:
I had a Raymarine 1000 tillerpilor on my old C&C 25. It was easy to install,
easy to use and in fact worked better than the 4000+ on my current boat.
The EV1000 might be
Burt:
I had a Raymarine 1000 tillerpilor on my old C&C 25. It was easy to install,
easy to use and in fact worked better than the 4000+ on my current boat.
The EV1000 might be a little small for your 33. With crew, gear, fuel, water,
etc., you’re probably up to the top end of that 13,000. Bette
Do you have room to put an extension to the rear or below decks to your rudder
shaft?
On my last boat I was able to put a standard linear drive aft and below the
tiller. It worked great and was out of sight but just a button press away.
A tiller mounted unit will work but you will find yourself
oun...@cnc-list.com] On Behalf Of Joe Della
Barba via CnC-List
Sent: Tuesday, March 03, 2015 9:01 AM
To: 'John Bousfield'; cnc-list@cnc-list.com; 'Bradley Lumgair'
Subject: Re: Stus-List Autohelm and raymarine
I might be interested in buying an old AH4000 box.
Joe Della Barb
I might be interested in buying an old AH4000 box.
Joe Della Barba
j...@dellabarba.com
Coquina
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of John
Bousfield via CnC-List
Sent: Tuesday, March 03, 2015 8:19 AM
To: Bradley Lumgair; cnc-list@cnc-list.com
Subject: Re: Stus
Bradley,
I have a Autohelm 5000 and ran into similar issues. I am updating all my
instruments with Raymarine and found out I can use my existing linear drive
unit just replace the control head using the EV200 then all my instruments
will communicate. I am using the linear drive because I have a com
Hi Bradley- My two bits for what it is worth- I would put money into an
autopilot before many of the systems on my boat. In fact, I just bought a new
one (Raymarine wheel pilot) because the old one was becoming unreliable and I
want to know it will work when I need it. I sail short handed or s
Hi Bradley,
Wouldn't you know it, I have one of those at my boat. Pre-Raytheon
days. I'm not sure mine even works anymore.
I say "at my boat" because I took it off during a boat work period
some time ago and never got around to reinstalling. So I believe
you're on the right path to use the b
Right now I'm thinking I will sail with the Depth and the wind "True / App"
and the speed paddle if I can get it to work and then the new Garmin
Echo50s and leave it a lone for a while. I will go tonight and hookup the
flux gate and the wind and take a new look at the (+) (-) on the GPS and
the Aut
: Re: Stus-List Autohelm St4000 how it should work with the GPS
To: cnc-list@cnc-list.com
Date: Tuesday, January 14, 2014, 4:31 AM
I worked with the paddle
wheel last night ad was able to
clean it. It now spins freely but shows however it still has
no activity on the
ohms meter. All that b
Covering a few things on the same topic.
1) ST50 Speed System ( Z095 & Z092 )
Wire colour code:
Screen - 0 volts - ground
Red - 5 volts - power
Green - 0 to 5 volt log pulse measured from green to screen, from speed sensor
Yellow - Temperature 1
Blue - Temperature 2
Power up the equipme
ed
or depth because they thought the GPS would just "take care of all that".
Cheers
Steve Hood
S/V Diamond Girl
C&C 34
Lions Head ON
--
Message: 8
Date: Tue, 14 Jan 2014 09:51:36 -0500
From: Stevan Plavsa
To: "cnc-list@cnc-list.com"
Su
speed through the water both
displayed you can find the best wind and the least adverse current ;)
Joe Della Barba
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Curtis
Sent: Tuesday, January 14, 2014 9:59 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it s
That helps . I can understand why it is needed. it would be a great help to
me . I do sail in the Beaufort / Broad / Morgan rivers more than anywhere
else. I have to fight 7 to 9 foot tidal changes. I mentioned in a another
post that I have been sailing real hard and doing real good with the water
t; *Joe Della Barba*
>
>
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Rich
> Knowles
> *Sent:* Tuesday, January 14, 2014 9:32 AM
> *To:* cnc-list Cnc-List
>
> *Subject:* Re: Stus-List Autohelm St4000 how it should work with the GPS
>
>
&
, 2014 9:32 AM
To: cnc-list Cnc-List
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Makes life interesting:)
Rich
On Jan 14, 2014, at 10:20 AM, Della Barba, Joe
mailto:joe.della.ba...@ssa.gov>> wrote:
If you go right in the very center of the Bay Bridge main span som
[mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rich Knowles
Sent: Monday, January 13, 2014 8:50 PM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Here in Halifax harbour, if I go parallel to and within a couple hundred feet
of the Panamax
Barba
Coquina
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Curtis
Sent: Tuesday, January 14, 2014 7:31 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
All that being said, how much does this speed help you anyway? I mean it
would NOT see changes when spinning it.
On Jan 14, 2014 9:18 AM, "Josh Muckley" wrote:
>
> Oh yeah, I believe your speed wheel uses what is called a hall-effect
transistor. It simply conducts momentarily in the presence of a magnetic
field. So 0 ohms is correct. You probably would even see any
, 2014 8:50 PM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Here in Halifax harbour, if I go parallel to and within a couple hundred feet
of the Panamax floating dry dock, a big chunk of steel, with the auto helm on,
I'll get steered right off c
Oh yeah, I believe your speed wheel uses what is called a hall-effect
transistor. It simply conducts momentarily in the presence of a magnetic
field. So 0 ohms is correct. You probably would even see any change when
you spin the wheel. The instrument just counts "clicks".
Josh
On Jan 14, 2014
Boat speed is very helpful for innumerable reasons.
The speed wheel shows speed through the water. The GPS shows speed over
ground. If you take the differance then you can see the speed of the
current.
The wind instrument uses boat speed to calculate apparent wind speed and
angle which is more
Curtis, your ohm meter likely wont show anything. Plug it into the instrument
to test it.
Rich
> On Jan 14, 2014, at 8:31, Curtis wrote:
>
> I worked with the paddle wheel last night ad was able to clean it. It now
> spins freely but shows however it still has no activity on the ohms meter.
I worked with the paddle wheel last night ad was able to clean it. It now
spins freely but shows however it still has no activity on the ohms meter.
All that being said, how much does this speed help you anyway? I mean it
will tell me how fast the river is passing under my boat but not if I’m
maki
I had to knock the pin out of my paddlewheel and replace the wheel and the
pin, since I had whacked into something hard and it stopped working, pretty
much. Bent the pin, knocked one of the lobes off the paddlewheel. Then I
put the new paddlewheel on backwards, and it worked well enough since I had
Tear them all out and send them to me, you'll never find any use for
them. In return I will send you my wind instruments, which mostly
consists of some cassette tape tied to the shrouds.
Cheers,
Paul.
On 14-01-13 09:56 PM, Josh Muckley wrote:
KEEP THE ELECTRONICS!
The speed wheel is probabl
Hi Curtis.
Apologies for sounding frustrated. You are asking some simple questions for
which there are relatively complex answers. I appreciate where you are as it's
a place where most of us have been at one point, but it's so long ago we have
forgotten:) I think we are all trying to answer you
KEEP THE ELECTRONICS!
The speed wheel is probably full of the last seasons marine growth. A
tooth brush should straighten that out.
Yes you can get the autohelm to steer to the wind. On my symrad unit I
have to configure it for one or the other. Not too hard but certainly not
on the fly. Stee
uot;
> *To: *cnc-list@cnc-list.com
> *Sent: *Monday, January 13, 2014 10:09:15 PM
> *Subject: *Re: Stus-List Autohelm St4000 how it should work with the GPS
>
> Rich,
>
> I have read and continue to read the manuals for all this equipment. I
> note a bit of frustration with reg
-- Original Message -
From: "Curtis"
To: cnc-list@cnc-list.com
Sent: Monday, January 13, 2014 10:09:15 PM
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Rich,
I have read and continue to read the manuals for all this equipment. I note a
bit of frustratio
Rich,
I have read and continue to read the manuals for all this equipment. I note
a bit of frustration with regards’ to my lack of understanding of this
equipment. I have only owned my C&C30 for a couple of years now, The boat
came with a lot of st50 auto-helm equipment
1) Tri-data
2) VMG
3)
@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Rich,
Not every time power off, but it seems in spring after winter where
batteries pulled and taken to basement that Need to Re swing the fluxgate
and adjust the gain. Maybe not, but it seems to lose this
That's possible as the units age. Again, possibly a capacitor leakage issue.
Minor inconvenience if it's only once a year.
Rich
> On Jan 13, 2014, at 21:51, "wwadjo...@aol.com" wrote:
>
> Rich,
> Not every time power off, but it seems in spring after winter where batteries
> pulled and take
Rich,
Not every time power off, but it seems in spring after winter where batteries
pulled and taken to basement that Need to Re swing the fluxgate and adjust the
gain. Maybe not, but it seems to lose this memory over winter.
Bill
Sent from my HTC
- Reply message -
From: "Rich Kno
least one singlehander that used a mark of some kind as a waypoint and got a
> direct hit while sleeping.
>
> Joe Della Barba
> Coquina
> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Marek
> Dziedzic
> Sent: Monday, January 13, 2014 1:01 PM
> To: cnc-
>Not to be picky, but your last step should not be required every time you shut
>off the power. The settings are retained in non-volatile memory.
The settings are saved, and should last over the winter. Some of the older
units are losing their ability to save into non-volatile memory.
Als
Gotta love automistake!
Rich
> On Jan 13, 2014, at 20:15, "wwadjo...@aol.com" wrote:
>
> Yeah, well Rich, tell that to my shrivel., please
> Bill walker
>
> Sent from my HTC
>
> - Reply message -
> From: "Rich Knowles"
> To: "cnc-list@cnc-list.com"
> Subject: Stus-List Autohelm St
Hmm. Bill, If you are saying every time you shut off the power to the auto
helm, the settings revert, that is not right. I've installed and set up many of
them and never had that problem except for one unit. The problem with that one
was an electrolytic capacitor that had been installed at the f
: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
>Though something to consider is that the 0183 standard is for a total of 4
>wires to send and recieve. RX+GND and TX+GND. I didn't see where you
>mentioned all those wires...sounded like
: Monday, January 13, 2014 1:01 PM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Supposedly, this is how accidents happen on Great Lakes. I don’t know if these
are urban legends or not, but I heard that, especially, on Georgian Bay, there
are
I rarely let Otto drive the boat from the GPS, but I will frequently set
the wind angle hold while we get drinks etc. This setting will keep the
boat sailing to the set of the sails rather than trying to set a
waypoint. We literally have sailed in a circle on Lake Michigan during
variable win
Ops, how does spell checker take autohelm to shrivel? H. Another topic
altogether.
Sent from my HTC
- Reply message -
From: "wwadjo...@aol.com"
To:
Subject: Stus-ListAutohelm St4000 how it should work with the GPS
Date: Mon, Jan 13, 2014 7:15 PM
Yeah, well Rich, tell that to my s
Yeah, well Rich, tell that to my shrivel., please
Bill walker
Sent from my HTC
- Reply message -
From: "Rich Knowles"
To: "cnc-list@cnc-list.com"
Subject: Stus-List Autohelm St4000 how it should work with the GPS
Date: Mon, Jan 13, 2014 5:38 PM
Not to be picky, but your last step sho
Not to be picky, but your last step should not be required every time you shut
off the power. The settings are retained in non-volatile memory.
Rich
> On Jan 13, 2014, at 18:24, Wwadjourn wrote:
>
> I almost shudder at posting in this thread, but . . . . . .
> One other point, read the manua
I almost shudder at posting in this thread, but . . . . . .
One other point, read the manual, and set the gain on the auto pilot. You will
never get optimum performance, read: a straight course, without doing this step
in the set up, AND every time that power is completely removed from the pilo
o base that on
>
> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rich
> Knowles
> Sent: January 13, 2014 5:48 PM
> To: cnc-list Cnc-List
> Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
>
> Well, we're not all good at everything
Cnc-List
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Well, we're not all good at everything!
Rich
On Jan 13, 2014, at 5:37 PM, dwight wrote:
Now you know why I asked such basic questions that some of you thought heavy
on Curtis.
_
he rudder angle and you have a "auto-weaver".
>
> My Simrad wheel-pilot on my Bristol 30 did not have either. Hence the
> knick-name.
>
>
>
> David F. Risch
> 1981 40-2
> (401) 419-4650 (cell)
>
>
> From: f...@postaudio.net
> Date: Mon, 13
taudio.net
Date: Mon, 13 Jan 2014 15:14:22 -0600
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Curt — seriously, read the installation manual for the ST4000. It NEEDS to
have the fluxgate compass input; it does NOT get heading info from GPS, nor
5:27 PM
To: cnc-list Cnc-List
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Curtis:
The fluxgate compass is the primary source of heading information for the
autopilot head and should not be disconnected.
When you push the "AUTO" button, the course computer
Now you know why I asked such basic questions that some of you thought heavy
on Curtis.
_
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rich
Knowles
Sent: January 13, 2014 5:27 PM
To: cnc-list Cnc-List
Subject: Re: Stus-List Autohelm St4000 how it should work with
Curtis:
The fluxgate compass is the primary source of heading information for the
autopilot head and should not be disconnected.
When you push the "AUTO" button, the course computer locks on to the compass
heading the boat is on and develops internal correcting signals as the boat
yaws to eit
Curt — seriously, read the installation manual for the ST4000. It NEEDS to
have the fluxgate compass input; it does NOT get heading info from GPS, nor
could it, as heading does not equal course over ground (COG) in most cases.
Hook that thing back up!
Fred Street -- Minneapolis
S/V Oceanis (1
I have a flux gate compass I disconnected it from the head because I
thought the auto-pilot head would now get its heading from the GPS unit?
So I will take some photos and show you what I have.
How will I ever nap a nap in???
On Mon, Jan 13, 2014 at 2:19 PM, Michael Brown wrote:
>
>
> >Thoug
quot;the interface" and having to constantly
> check the course et al. Seems safer to me.
>
> David F. Risch
> 1981 40-2
> (401) 419-4650 (cell)
>
>
> Date: Mon, 13 Jan 2014 13:13:46 -0500
> From: cpt.b...@gmail.com
> To: cnc-list@cnc-list.com
> Subject: Re: Stu
>Though something to consider is that the 0183 standard is for a total of 4
>wires to send and recieve. RX+GND and TX+GND. I didn't see where you
>mentioned all those wires...sounded like too few.
The ST4000 control head is NMEA IN only, two wires marks - +.
>
> So now, If I understand yo
> Date: Mon, 13 Jan 2014 13:13:46 -0500
> From: cpt.b...@gmail.com
> To: cnc-list@cnc-list.com
> Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
>
> I just googled it looking for an answer to me problem and This is the
> website that I c
e: Mon, 13 Jan 2014 13:13:46 -0500
From: cpt.b...@gmail.com
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
I just googled it looking for an answer to me problem and This is the website
that I came up
with.http://www.jfaughn.com/crew_boat_project
I just googled it looking for an answer to me problem and This is the
website that I came up with.
http://www.jfaughn.com/crew_boat_projects/projects/garminautohelm/492autohelm.htm
On Mon, Jan 13, 2014 at 12:10 PM, Jim Watts wrote:
> The blue wire on Raymarine 4000 autopilots is the -V for the
Thanks Frederick, That's the information I was needing.
The wires on the new Garmin "do" have 2 wires with tags on them one with a
(TX-) and one with (TX+) then the back of the ST-4000 looks like this.
Thanks for your help. I will try this.
the
On Mon, Jan 13, 2014 at 10:35 AM, Frederick G Str
Message: 3
Date: Mon, 13 Jan 2014 10:24:46 -0400
From: "dwight"
To:
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Message-ID: <51831FEBD26A4707BA3920EB0655F0F4@your4dacd0ea75>
Content-Type: text/plain; charset="us-ascii"
I
The blue wire on Raymarine 4000 autopilots is the -V for the power supply.
I suggest you track down whoever told you to hook it up like that and beat
him senseless. Read the manuals for each, it isn't rocket science.
Jim Watts
Paradigm Shift
C&C 35 Mk III
Victoria, BC
On 13 January 2014 05:04,
Curt — it’s been my experience that pretty much NO equipment uses the same
color wire for the same thing, even among equipment from the same manufacturer.
You need to connect the NMEA0183 output wires from the GPS to the NMEA0183
input wires on the autopilot; TX+ and TX- on the Garmin to RX+ an
10:10 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm St4000 how it should work with the GPS
Umm... not sure about the st4000 it should also have a button kinda like a
NAV that will tell it to listen to the broadcast course to steer.
Everything else sounds like you have it.
Though
Here's the URL for Raymarine manuals:
http://www.raymarine.com/view/?id=1836
Rich
> On Jan 13, 2014, at 9:04, Curtis wrote:
>
> Got it all wired in today and I need some help.
> I have an older model Autohelm St4000 and a new Echo50s Garmin.\I have the
> blue wire from the control head going
Umm... not sure about the st4000 it should also have a button kinda like a
NAV that will tell it to listen to the broadcast course to steer.
Everything else sounds like you have it.
Though something to consider is that the 0183 standard is for a total of 4
wires to send and recieve. RX+GND and T
Hi Curtis,
With everything hooked up correctly, I think you need to "engage" the
auto-pilot.
As in:
http://www.youtube.com/watch?v=3jd1Ih8EUmw
Cheers, Russ
At 05:48 AM 13/01/2014, you wrote:
No, The guy at Garmin said that the echo50s I purchased is
compatible with 0183 and should
Curtis. Do you have the manual for the gear? If not, get on the Raymarine site,
download it and read it. Operation is quite simple.
Rich
> On Jan 13, 2014, at 9:04, Curtis wrote:
>
> Got it all wired in today and I need some help.
> I have an older model Autohelm St4000 and a new Echo50s Garm
No, The guy at Garmin said that the echo50s I purchased is compatible with
0183 and should work fine.
Wire color to color and it should be fine. it also speaks the 2000. I
called raymarine and they said the difference in in the version of the 0183
in my equipment. the older version is vr 3.0 the n
I guess I jumped the assumption gun on the last responce. You question is
too vague. I should have started with, "What protocol is the garmin
using? What protocol is the autohelm using? What protocal are your
masthead instruments using? If you want them to all talk together then you
will proba
The garmin should have a nav button or other way to get it to start
navigating a course or to a waypoint. That should start broadcasting a
course to steer signal. I don't know about the wiring specifically so I
have to assume you followed the manuals for the autohelm and garmin and
matched the in
I would guess that you probably have a Type 2 (up to 33,000 lbs displacement),
due to the fact that your course computer is a 300; if it was a Type 1, you’d
probably have the smaller 100 course computer. I just checked the manual for
the 100/300 systems — I love that Raymarine has the older man
Sent: Saturday, November 30, 2013 4:16 PM
> To: cnc-list@cnc-list.com
> Subject: Re: Stus-List Autohelm Auto pilot
>
> Fred — can you get me the model number of the linear drive in your boat (I’m
> assuming it’s linear…)? Specs on the website show the displacement of the
, November 30, 2013 4:16 PM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm Auto pilot
Fred - can you get me the model number of the linear drive in your boat (I'm
assuming it's linear.)? Specs on the website show the displacement of the
C&C44 at 20,000 lbs; the drive y
Fred — can you get me the model number of the linear drive in your boat (I’m
assuming it’s linear…)? Specs on the website show the displacement of the
C&C44 at 20,000 lbs; the drive you’ve got will determine whether you’ll need
the Raymarine ACU-200 or ACU-400 course computer. The Type 1 drive
repairs.
Thanks
Fred Hazzard
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Frederick
G Street
Sent: Saturday, November 30, 2013 11:14 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Autohelm Auto pilot
Fred - if you're in a position to get a new autopilot c
Fred — if you’re in a position to get a new autopilot course computer, I’d
recommend it. The new ones from Raymarine are nice; I can price you one at my
cost, if you’d like. You’ll also need to get a new control head, as the older
ones don’t have the functionality to program the new course com
True statement.
Rich
> On Nov 29, 2013, at 12:27, Jim Watts wrote:
>
> I believe that any brain will drive your system, even non-Raymarine ones, and
> the new brain boxes are much smarter than the old ones. I'm sure the experts
> will chime in...Fred, Rich?
>
>
>> On 29 November 2013 08:25
I believe that any brain will drive your system, even non-Raymarine ones,
and the new brain boxes are much smarter than the old ones. I'm sure the
experts will chime in...Fred, Rich?
On 29 November 2013 08:25, Fred Hazzard wrote:
> One of the casualties on my recent cruise to Mexico is the brai
Fred. I have an Autohelm 6000 and it is still working fine. There are a
couple of spare connections which I suspect were for a hard wired remote. If
you come upon a source for older Autohelm equipment I'd appreciate hearing
too; having the remote would be handy.. Thanks
From: CnC-List [mailto:c
On Aug 1, 2012, at 2:35 PM, Chuck S wrote:
> Moral, be sure your lever screw is snug, but not so tight that it prevents
> the lever from swinging over the nubs which are intended to hold the lever on
> or off.
Okay, Wal, it's off to you now for further comment... :^)
Fred Street -- Minneapol
92 matches
Mail list logo
