Rich,

I have read and continue to read the manuals for all this equipment. I note
a bit of frustration with regards’ to my lack of understanding of this
equipment. I have only owned my C&C30 for a couple of years now, The boat
came with a lot of st50 auto-helm equipment



1) Tri-data

2) VMG

3) ST4000

4) Wind

5) Multi

6) Speed Trim

7) NAV-Data

8) I also have a 36” pole with a wind feather on the top of it? Z159



Transducers’= (wind speed true/app Direction)

(Water speed paddle wheel)

(Depth temp)

(Wind angle? Z159)

(Fluxgate)



Everything seams to power up, but the paddlewheel will not turn freely. And
there is no continuity in the cable? So, it’s fair to say the speed trans
is no good.

The fluxgate I was able to swing in as the “Manual” instructed. I’m able to
set the clutch in place and hold the boat at the heading I point it at
using the st4000 so I know that works. But reading the above makes sense
that it would be independent of the Garmin GPS. However I was told that’s
what makes the system so cool is It would follow a courts set by gps. If I
read Schiller’s post correctly I could set it to receive the wind vane so I
might steer a wind angle? Now that would be progress.



Moving forward I will hook back up the Fluxgate compass and reconsider what
else?



Thanks again its just so much to take in for someone that has never been
involved in marine electronics and new to boat ownership as well.

I will get it. It just may take me more time than I was hoping for.

Thanks again for all the advice and help. With out you guys I would
flounder for months on this stuff.  Maybe I should just cut it all loose
and e-bay it. Just use the Garmin and the depth sounder. It would be a way
to watch both ends of the boat in close anchorages.

Cheers, Curtis


On Mon, Jan 13, 2014 at 4:26 PM, Rich Knowles <r...@sailpower.ca> wrote:

> Curtis:
>
> The fluxgate compass is the primary source of heading information for the
> autopilot head and should *not* be disconnected.
>
> When you push the "AUTO" button, the course computer locks on to the
> compass heading the boat is on and develops internal correcting signals as
> the boat yaws to either side of the original heading and uses those
> cross-track error signals to drive the wheel and hold the course steady.
> Once properly set up, the course holding abilities of the ST4000 are quite
> good and you should be on a constant course in the direction originally
> set. This way of using the ST4000 is the standard way of operating. It's
> just fine for relatively short legs but, as it only uses the boat's heading
> as a reference, it cannot compensate for current or leeway of the boat. In
> other words, you could be doing 220 deg for several hours and be miles of
> your intended destination if a cross current caused by tide has pushed you
> away from the rhumb line.
>
> To avoid getting pushed off course by factors that the fluxgate compass
> cannot measure or compensate for, an external source of cross-track error
> signals is needed that uses the final destination point as the reference
> from which to calculate whether course correction is needed.
>
> When you have a "GO TO" destination set up and activated on the GPS unit,
> the GPS will develop off course signals that can be used by the auto helm
> computer to steer the boat to the destination. That information is
> delivered to the ST4000 via the NMEA signals.
>
> Pardon me if you are aware of this already. I strongly recommend reading
> the manuals and, if there are terms that are unclear, Google them up.
>
> Hook that compass up and RTFM!
>
> Rich Knowles
> INDIGO LF38
> Halifax, NS.
>
>
>
>
>
> On Jan 13, 2014, at 4:26 PM, Curtis <cpt.b...@gmail.com> wrote:
>
> I have a flux gate compass I disconnected it from the head because I
> thought the auto-pilot head would now get its heading from the GPS unit?
>
> So I will take some photos and show you what I have.
>
> How will I ever nap a nap in???
>
>
> On Mon, Jan 13, 2014 at 2:19 PM, Michael Brown <m...@tkg.ca> wrote:
>
>>
>>
>> >Though something to consider is that the 0183 standard is for a total of
>> 4
>> >wires to send and recieve.  RX+GND and TX+GND.  I didn't see where you
>> >mentioned all those wires...sounded like too few.
>>
>>
>> The ST4000 control head is NMEA IN only, two wires marks - +.
>>
>>
>> >
>> > So now, If I understand you correctly. I first have to create a route
>> then to
>> > start navigating a course or to a way-point.  That should start
>> > broadcasting a course to steer signal. then I in-gauge the st4000  by
>> > pressing the +10 and -10 at the same time and it should start taking
>> > direction from the Garmin?
>> > does this sound correct?
>> >
>>
>>
>> With NEMA to the ST4000 it depends on what is being sent. Autohelm
>> describes two
>> scenarios,  automatic acquisition and manual acquisition.
>>
>> Automatic - both cross track error and bearing to waypoint are sent
>> Manual - only cross track error is sent
>>
>> With automatic get everything engaged and press +10 and -10 together. The
>> manual
>> requires that you get on course withing 5 degrees of the bearing to the
>> waypoint and
>> cross track less than 0.1 nm, then press +10 and -10 together.
>>
>> My guess is, and strictly a guess, is that the ST4000 uses its own
>> fluxgate compass
>> for navigation and takes some error correction from NEMA for cross track.
>>
>>
>>
>>
>> >I know it has probably been done by others but I am not sure that I
>> would
>> >ever let my ST 4000 plus steer a course unattended based on transfer
>> data
>> >from my chart plotter.
>>
>>
>> I wonder if that was what Autohelm was thinking, they seem to use the
>> fluxgate compass.
>>
>>
>> > Curt ? it?s been my experience that pretty much NO equipment uses the
>> same color wire for the same thing, even among equipment from the same
>> manufacturer.
>>
>> >You need to connect the NMEA0183 output wires from the GPS to the
>> NMEA0183 input wires on the > autopilot; TX+ and TX- on the Garmin to RX+
>> and RX- on the Raymarine.
>>
>> >I can guarantee that the chances of any two of these wires having common
>> colors is about zero.
>>
>>
>> Supposedly the + is Red and - is Blue, however Autohelm agrees with you.
>> They are marked + and - only.
>>
>>
>> Michael Brown
>> Windburn
>> C&C 30-1
>>
>>
>> _______________________________________________
>> This List is provided by the C&C Photo Album
>> http://www.cncphotoalbum.com
>> CnC-List@cnc-list.com
>>
>>
>
>
> --
>
> *At sea, I learned how little a person needs, not how much. -  Robin Lee
> Graham*
>
>  _______________________________________________
> This List is provided by the C&C Photo Album
> http://www.cncphotoalbum.com
> CnC-List@cnc-list.com
>
>
> _______________________________________________
> This List is provided by the C&C Photo Album
> http://www.cncphotoalbum.com
> CnC-List@cnc-list.com
>
>


-- 

*At sea, I learned how little a person needs, not how much.-  Robin Lee
Graham*
_______________________________________________
This List is provided by the C&C Photo Album
http://www.cncphotoalbum.com
CnC-List@cnc-list.com

Reply via email to