My forward hatch is leaking.
What should I use to re bed the hatch to the deck.
Also what do l use to secure the plexiglas to the frame.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Your contributions help pay the fees associated with this list and help to keep
it active. Please help by maki
I need to seal my forward hatch. The plexiglass is sealed with a black
rubber like substance .
Any suggestions as to what I need to buy?
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
Your contributions help pay the fees associated with this list and help to keep
it active. Please help by maki
I had similar problem that I fixed by having a small brass plate made with
vin number stamped on it. I epoxied it to the upper port corner of the
transom.
No problems in the US or Mexico.
Fred Hazzard
Fury
C&C 44
Portland Or
On Fri, Nov 8, 2024 at 3:55 AM Motion Designs Limited via CnC-List &
Sent from my iPhoneOn Jun 12, 2023, at 2:28 PM, David Risch via CnC-List wrote:
If you re-powered, or just have a good running engine, and did not thoroughly clean the tank and tank pick-up. Your playing Russian roulette. Especially in rough weather when all that gunk gets stirred up.
d. I still have a squeeze in the line. It makes it much easier to reprime if needed. Like when I ran out of fuel. Fred Hazzard S/V Fury Portland, Oregon Sent from my iPhoneOn Jun 12, 2023, at 2:28 PM, David Risch via CnC-List wrote:
If you re-powered, or just have a good running engine, and
I removed the hot water tank aft of the double bed on the starboard side. Depending the generator size, there may be room. I put in a demand propane hot water system as a replacement. Fred Hazzard S/ V FuryCnC 44Portland, Or Sent from my iPhoneOn Dec 4, 2022, at 7:16 PM, David NCW via CnC-List
The aluminum plate in the cockpit of my 44 shows it was built in Rhode Island.
It is the 7th one built.
The HIN was removed when painted.
Fred Hazzard
S/V Fury
Sent from my iPhone
> On Jun 26, 2022, at 6:19 PM, Don Kern via CnC-List
> wrote:
>
>
> Dan,
>
> You
1986 C&C 44 hull nbrs 7 and 8 are here in Portland. Both were originally
delivered to Seattle. No idea as to country of origin.
Fred Hazzard
Sent from my iPhone
> On Jun 25, 2022, at 3:48 AM, Dan via CnC-List wrote:
>
>
> Hi all,
> Just sending a call out to only C
Do any of you listers have experience rolling and tipping your boat with
Epifanes 2 part poly-urethane?
I would appreciate any comments about the process and results.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
15 years ago I revarnished the interior with an exterior satin poly urethane. I
did the trim with gloss. It has held up remarkably well.
A key a good job is prep. Sand and wipe down well.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Jun 18, 2022, at 11:36 AM
How can I tell the maker of the hatch’s used on my 1986 C&C 44?
Fred Hazzard
S/V Fury
Portland Or.
Sent from my iPhone
> On Feb 17, 2022, at 4:17 PM, Dreuge via CnC-List
> wrote:
>
>
> The gaskets that A&H used are EPDM foam cord. This can be purchased in 3ft,
&
water.
😁
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Dec 11, 2021, at 3:43 PM, Ronald B. Frerker via CnC-List
> wrote:
>
>
> Martin, do I remember correctly; wasn't your boat originally Esta Es from
> Lake Michigan?
> Ron
> Wild
Try Second Wind Sails. They have a lot of used sails.
Fred Hazzard
S/V Fury
C&C 44
Sent from my iPhone
> On Nov 14, 2021, at 6:35 AM, Peter Kirkwood via CnC-List
> wrote:
>
>
>
>
>> On Sun, Nov 14, 2021 at 9:06 AM Scott Baker via CnC-List
>> wrote:
Yesterday my 3/4 oz. chute exploded in a big wind.
Now I am looking for a used replacement. Lead time to get a new one more than 6
months.
So,if there are any C&C 44 listers out there with a chute to sell, I am
interested.
Fred Hazzard
C&C 44
S/V Fury
Portland Or
Sent from m
Tom, could be crud in the tank blocking the pick up line to the filter.
Should be rubber line from tank to filter.
Disconnect line at filter and blow into it. Yumm!
Fred Hazzard
SV Fury
Sent from my iPhone
> On Aug 3, 2021, at 8:35 PM, Tom Buscaglia via CnC-List
> wrote:
>
> W
Years ago a small piece of wood came up thru the shaft log into the bellows and
wedged itself between the stainless and graphite rings. The boat sank
overnight.
The moral of this story is that you should periodically check the pressure of
the bellows.
My stainless ring had slipped.
Fred
I am in need of someone to repair the brain of my st 6000 autopilot.
Any suggestions?
Fred Hazzard
S/V Fury
C&C 44
Sent from my iPhone
> On Apr 19, 2021, at 8:38 AM, Peter Kirkwood via CnC-List
> wrote:
>
>
> Agree. Went with the hydraulic ram on my 38 and it is e
Wow. I am glad I asked.
Thanks
Fred
Sent from my iPhone
> On Apr 1, 2021, at 12:26 PM, dwight veinot via CnC-List
> wrote:
>
>
> Cleaning. Flushing your heat exchanger? Mayber
>
>> On Thu, Apr 1, 2021 at 12:01 PM Fred Hazzard via CnC-List
>> wrote:
>
As senior citizen I suffer from the dreaded malady
CRS.
Yesterday while visiting Fury I found a gallon of white vinegar.
Hopefully, one of you can remind me what is for.
Thanks
Fred Hazzard
SV Fury
C&C 44
Portland, Or
Sent from my iPhone
Thanks to all of the subscribers that contribute
fully functioning VHF at the helm.
Fred Hazzard
S/V Fury
C&C44
Portland Or
Sent from my iPhone
> On Mar 28, 2021, at 6:25 AM, Bill Coleman via CnC-List
> wrote:
>
>
> Okay, it's morning, and I've calmed down. So, either hook up your speakers,
> get
list mail went to junk.
Fred Hazzard
S/ V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Mar 23, 2021, at 9:19 AM, Stu via CnC-List wrote:
>
>
> Google has initiated some nonsense spam filters that has affected a lot of
> members. According to our provider, they are r
Using an oil absorbing pad under engine and detergent in the bilge helped with
smells, but the best thing was running a dehumidifier. It lowered the humidity
to 55 percent and improved the smell dramatically.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Mar 1
of half inch white pvc pipe on the baby stay. The pvc pipe stays on the
baby stay year around. It protects the mast from the stay banging against the
mast when the stay is not in use.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Feb 16, 2021, at 6:35 PM, J
David, I had similar problem. As it was not structural I cut out the bad wood
and glued in a piece of ordinary plywood. I then re-veneered with teak. You can
buy very thin paper backed teak veneer at specialty hardwood suppliers.
Fred Hazzard
C&C 44
S/V Fury
Portland Or
Sent from my iP
Doug,
I have a complete system. Four displays, 2 key pads and two working brains.
Make me an offer including shipping and it will be yours.
Come back to me to my email if interested.
fshazzard@ gmail.com
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Dec 5, 202
issue the ocean will kick your butt.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Mon, Oct 26, 2020 at 1:41 PM wrote:
>
>
> Hi All,
>
>
>
> I am considering moving my recent purcahse from So Cal to Washington
> State. I have two options… 1) move it from So Cal ne
will appreciate your thoughts.
Fred Hazzard
S/ V Fury
C&C 44
October is the time to show your appreciation with a small contribution to this
list to help offset the costs. If you want to support the list - use PayPal to
send contribution -- https://www.paypal.me/stumurray Thanks - Stu
I accomplished the same thing with a squeeze bulb in the line from the
tank. It not only primes the filter bowl but also can quickly pump fuel and
air thru the fuel pump and secondary filter. It will also tell you if
there is a blockage in the pick up line from the tank.
Fred Hazzard
S/V Fury
C
Stu, Sorry I don’t recall.
Fred
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send contribution -- https://www.paypal.me/stumurray
Sure Marine in Seattle can probably help.
Fred Hazzard
S/V Fury
On Thu, Oct 1, 2020 at 10:09 AM Josh Muckley wrote:
> Correct.
>
> No. I haven't looked into it.
>
> On Thu, Oct 1, 2020, 13:07 Edd Schillay wrote:
>
>> Josh,
>>
>> So each burner has
-- Forwarded message -
From: Fred Hazzard
Date: Mon, Sep 28, 2020 at 12:10 PM
Subject: Emails
To:
Another issue have is that my sent emails that I initiate do not show up on
the site until someone responds.
Before I learned to look in spam for a response I thought my messages
Joel, Magic looks interesting.
I am not going to try it as the cost of product and bottom preparation more
than I am willing to do.
Thanks
Fred Hazzard
S/V Fury
On Sat, Sep 26, 2020 at 8:17 AM Joel Delamirande
wrote:
> Have you looked up my product
>
> On Thu, Sep 24, 2020 at 12:2
Still looking for recommendations for bottom paint for use in fresh water.
I’m interested in resistance to slime, durability and ease in application.
Here in Portland, Or we don’t haul out every year, so lasting over several
seasons is important.
Fred Hazzard
S/V Fury
On Mon, Sep 21, 2020 at 2
I am getting ready to have the bottom repainted. The yard is recommending
Petit Ultima SR 60.
Do any of you have experience or strong opinions about this paint.
Our boat is in fresh water 99 % of the time.
Other paint recommendations would be appreciated.
Fred Hazzard
S/V Fury
C&C 44
Portlan
Dennis, my cast aluminum stem and line chalks looked similar. I hand
sanded and painted them with 2 coats ofRustoleum krylon flat black.
This was 2 years ago and they still look good.
Fred Hazzard
S/V Fury
On Mon, Sep 21, 2020 at 6:51 AM Bill Coleman wrote:
> Looking closely at that pict
On Sat, Sep 19, 2020 at 10:45 AM Fred Hazzard wrote:
> Josh mentioned that cylinder glazing can occur if the engine is not run at
> 80 percent for extended periods of time. We motor out from the dock for 5
> or 10 minutes, set the sails and shut down the engine. We get a fairly
>
rid of the glazing short tearing down the
engine?
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
Another benefit to the squeeze bulb is that if the tank pick up line gets
plugged with gunk, the bulb will collapse under the vacuum created.
By blowing into the line you can usually clear the blockage. Yum!
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Mon, Sep 7, 2020 at 5:24 AM David Risch
some and the epoxy seal failed.
There are 12 1/4” bolts clamping the inner and outer collars to the deck.
I would love it there is liquid epoxy like capt tolleys that will remain
flexible.
I welcome your ideas.
Fred Hazzard
S/V Fury
C&C 44
Portlan
we
added. Eight inches and 400 lbs.
Our upwind performance improved dramatically in moderate to heavy winds.
Our light air performance was slightly slower.
I recall our phrf rating was lowered 3 seconds a mile.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Sat, Jun 13, 2020 at 5:21 AM dwight ve
Good strategy to get something before paying for a survey. Then when
surveys come back you be able to negotiate further.
Fred Hazzard
On Tue, Feb 25, 2020 at 4:20 PM bwhitmore via CnC-List <
cnc-list@cnc-list.com> wrote:
> While I agree with, and respect Josh, having done the steerin
Kevin, I can’t imagine what the bottom is like if it is as neglected as
much as the top side is.
Here’s where a tough inspector will save you either a heartache and or a
boatload of money.
Good luck.
Fred Hazzard
On Tue, Feb 25, 2020 at 12:20 PM Josh Muckley via CnC-List <
cnc-list@cnc-list.
Kevin, you might check at Harbor Freight.
Fred Hazzard
On Wed, Feb 19, 2020 at 5:28 AM Kevin Driscoll via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hi all,
> I am looking for a reasonably priced and quality moisture meter so I can
> poke around my boat and others. Doe
I am surprised that all the 30’s are rated the same given the dramatic
differences in conditions they race in. San Francisco verses San Diego for
example.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Fri, Dec 13, 2019 at 7:08 AM Gary Nylander via CnC-List <
cnc-list@cnc-list.com> wro
What do listers like to clean and deodorize their bilge? Mine needs a
major clean and freshening.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is gre
Does any have 3/4 oz symmetrical spinnaker for C&C 44 that they would like
to sell?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If
connecting cable and connectors.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send contribu
e external tubes and can offer some lessons
> learned when I replaced ours a few years back
>
>
>
>
>
> John and Maryann
>
> Legacy III
>
> 1982 C&C 34
>
> Noank, CT
>
>
>
>
>
>
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list
mp;C 34R
>
>
> On April 9, 2019 at 12:47 PM Fred Hazzard via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
> I am replacing the cable. Is the cable fastened to the pedestal some near
> where the cable attaches to the shi
I am replacing the cable. Is the cable fastened to the pedestal some near
where the cable attaches to the shift lever?
Thanks
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
Thanks everyone for supporting this list with your contributions. Each
broke the cable.
What caused the transmission to bind up? I assumed the prop was not
spinning while in reverse.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every on
to the
engine.
Thanks
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send contribu
My experience is that with epoxy/ heavy varnish, when you get a chip or
crack down to bare wood, water creeps into the adjoining areas and turns
dark. The only fix is strip and do it again.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Mon, Feb 18, 2019 at 3:36 PM Dave Godwin via CnC-
Question: without a check valve how do you stop the pump from continually
recycling the water remaining in hose. It’s almost 20 feet from the pump
and switch to the transom.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Tue, Jan 15, 2019 at 9:16 AM Bruno Lachance via CnC-List <
cnc-l
I have been using Delo 30 in my Yanmar.
What you use?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list -
bulb was when the engine quit the bulb would go flat and I could
immediately tell if the hose was clogged.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Wed, Nov 14, 2018 at 3:03 PM Dennis Peters via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hi,
>
> I had a very similar problem las
I tried to buy a halyard at West M today. Turns out good high tech line is
25% off. The 40% only was on cheap dock line.
When does Defender have their sale?
Where else should I look?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone
We have rarely had to use our baby stay. But, when we needed it, it was a
real comfort.
To keep lines from hanging up when it is stowed against the mast, I put it
in about 10 feet of half inch plastic conduit. The conduit helps slide the
sail across when the baby stay is being used.
Fred Hazzard
leaving something to start you engine.
On our boat we have 4 batteries with over 400 ah. Even with this we need to
charge every 3 days.
The other thing you should look at is the insulation of your fridge. It can
make a big difference.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Sat, Oct 13, 201
.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Thu, Oct 11, 2018 at 8:54 AM Matthew L. Wolford via CnC-List <
cnc-list@cnc-list.com> wrote:
> If you haven’t pulled one before, you may be startled by how fast water
> rushes in. Remain calm, and have your blank handy.
>
> *From:*
20 years I have very actively raced a Cal 20 in a one
design fleet of 12 to 20 Cal’s.
That brings me to the ripe old age of 76 with 71 years of boating and 69
years of sailing and 18 years in C&C’s.
Wahoo!! Still sailing after all these years.
Fred Hazzard
Fury
Portland, Or
On Thu, Sep 27,
What finish is on your table and in what condition?
What would you like it to look like?
Fred Hazzard
Fury
Portland Or
On Mon, Sep 24, 2018 at 12:48 PM David via CnC-List
wrote:
> Hello,
>
> I am taking out my cabin table from my 81' 40- 2 to refinish this winter.
> Any
rates compare to other areas?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use PayPal
to send contribu
Did the sealant and tape delam from the window or the boat ?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the
Veiko, when I bought my boat the hin number on the transom was lost when
owner had it painted in California. When I registered it in Oregon, they
assigned a new number that I put on the transom. My insurance company
accepted it with no questions.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On
Peter, they are just what I need.
Now I have to figure out how to get Canadian funds to you.
Fred Hazzard
On Fri, Aug 10, 2018 at 9:46 AM Persuasion37 via CnC-List <
cnc-list@cnc-list.com> wrote:
> I would also like a picture
>
> Thanks
>
> Mike
> PERSUASION
> C&
Any chance you can send me a picture of a base?
Fred Hazzard
On Thu, Aug 9, 2018 at 9:56 PM Fred Hazzard wrote:
> Peter, I think these are the ones I need for my boat. I will take them.
> Fred Hazzard
> S/V Fury
> Portland, Or
>
> On Thu, Aug 9, 2018 at 9:40 PM Peter
Peter, I think these are the ones I need for my boat. I will take them.
Fred Hazzard
S/V Fury
Portland, Or
On Thu, Aug 9, 2018 at 9:40 PM Peter Fell via CnC-List <
cnc-list@cnc-list.com> wrote:
> I have four never-used 'Type D' bases available.
>
> South Shore offers
According to my electrician friend it is not uncommon for a breaker to
fail.
Fred Hazzard
S/V Fury
CnC 44
Portland Or
On Sat, Aug 4, 2018 at 11:03 PM Tom Buscaglia via CnC-List <
cnc-list@cnc-list.com> wrote:
> Frost day puts our 3 week summer cruise, headed to the Rendezvous next
>
to drink along...
>
> Tom Buscaglia
> S/V Alera
> 1990 C&C 37+/40
> Vashon WA
> P 206.463.9200
> C 305.409.3660
>
>
> On Jul 16, 2018, at 6:24 PM, cnc-list-requ...@cnc-list.com wrote:
>
> Message: 3
> Date: Mon, 16 Jul 2018 15:37:37 -0700
> From: Fred Hazz
I feel your pain. Been there done that. $30,000 later and the boat was like
new again. I love insurance.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Mon, Jul 16, 2018 at 10:55 AM Tom Buscaglia via CnC-List <
cnc-list@cnc-list.com> wrote:
> David
>
> I'll echo the other
Tom, we just stayed Saturday evening at your clubs dock in Quartermaster
harbor. What a great facility. I also was able see the marvelous Alera. It
looks almost like a new boat.
Thanks for the hospitality. Your resident live aboard is a neat old guy to
talk with.
Fred Hazzard
S/V Fury
C&
My 4 cyl Yanmar (non turbo) has begun to smoke a lot more when first
starting. It is a blue smoke that mostly goes away when it warms up. It
starts very easily and runs smoothly with good power.
I would love to hear your opinions of possible problems and cures.
Fred Hazzard
S/V Fury
C&
I have 2 at home and 4 on my boat. How do they deal with all those?
Fred Hazzard
S/V Fury
C&C 44
Portland Or
On Sun, Jul 1, 2018 at 7:30 PM Dennis C. via CnC-List
wrote:
> It was discussed but we may have new listers since then.
>
> It's fairly easy. Have your extinguisher
I have had great success with Minwax polyurethane satin on large surfaces
and gloss on trim pieces. I applied on large areas with 4” high density
foam roller.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Tue, Jun 26, 2018 at 2:59 PM Robert Boyer via CnC-List <
cnc-list@cnc-list.com
My experience with Polyglow was poor. Initially it looked good.
Unfortunately, it soon showed lots of dark pollution streaks on a light
colored surface. It was difficult to remove.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Mon, Apr 23, 2018 at 7:09 AM Bruce Whitmore via CnC-List <
c
Andy, speaking of Algrip what is the best way to deal with minor surface
abrasions ?
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
Sent from my iPhone
> On Apr 20, 2018, at 12:36 PM, Andrew Burton via CnC-List
> wrote:
>
> Ok, assembled wisdom, what is the best wax to keep m
By beveling and polishing the edges you prevent tiny crevices from becoming
major cracks.
Fred Hazzard
S/V Fury
Portland Or
Sent from my iPhone
> On Dec 14, 2017, at 8:52 AM, Gary Russell via CnC-List
> wrote:
>
> Good point! I also put a 45 degree bevel on the back side of t
.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Dec 12, 2017, at 11:38 AM, Josh Muckley via CnC-List
> wrote:
>
> When I bought my new mainsail the sail maker was kind of aloof and
> unconcerned regarding sail stretch. I was quite interested in the bol
Joe the I on my 44 is 59’.
Fred Hazzard
S/V Fury
Portland Or
Sent from my iPhone
> On Dec 6, 2017, at 12:10 PM, Joel Aronson via CnC-List
> wrote:
>
> All,
>
> i'm looking for a #4 dacron jib for my 44. I is 55. Total area no more than
> 400 sq feet. Make your
What causes it to start poorly? To start it we have to give it full throttle.
One more clue is that when it first fires some white smoke comes out..
Fred Hazzard
S/V Fury
Portland Or
Sent from my iPhone
___
Thanks everyone for supporting this
If you are happy with the color you have take a piece with you and your
supplier will match.
Fred Hazzard
S/V Fury
C&C 44
Portland Or
Sent from my iPhone
> On Nov 19, 2017, at 2:52 AM, Rod Stright via CnC-List
> wrote:
>
> Hi Gary,
>
> Is there a name for the c
now want a 44😀. 8 foot itis
>> Bill Walker
>> CnC 36
>>
>> Sent from AOL Mobile Mail
>>
>>
>>
>> On Tuesday, November 7, 2017 Fred Hazzard via CnC-List
>> wrote:
>>
>> Dan thanks for the tour. Your 44 looks great. Ple
Dan thanks for the tour. Your 44 looks great. Please keep sending your videos
. If you have questions, I might have a suggestion.
Fred Hazzard
S/V Fury
C&C 44
Portland, 44
Sent from my iPhone
> On Nov 7, 2017, at 12:56 PM, Dan via CnC-List wrote:
>
> Hey guys, if you want to c
h the rubber parts.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
The bills have started coming in for the year 2018 and have gone up again.
October will be our fund raising month. Please consider sending a small
contribution to help keep this lis
Can anyone tell me if C&C's built in 1986 used butyl rubber tape under
various tracks and rails. I have a baby stay track and jib car track that
appear to be leaking.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
<https://www.avast.com/sig-email?utm_medium=email&utm_source=l
My Awlgrip 14 yrs old and looks good except for some light dock rash. I'd
like to polish out these surface blemishes. What should I do or not do?
Fred Hazzard
S/V Fury
C&C 44
Portland,Or
On Sep 9, 2017 9:21 AM, "Dennis C. via CnC-List"
wrote:
> AwlCare is good stuff.
stay on and a lot of running back on and baby stay on after you have
dropped the sails be sure to ease the running back, as suddenly releasing
it can bring the mast down.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&ut
Congrats Daniel. They are great boats. This forum has some very
knowledgeable and helpful members.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Aug 14, 2017 2:28 PM, "Daniel Cormier via CnC-List" <
cnc-list@cnc-list.com> wrote:
> Hey all, I just wanted to share that I&
Adam I just replaced a port light using VHB tape and am very pleased with
results. The tape with the Dow silicon sealant are very secure and
waterproof. Follow the good advise of our fellow listers and the project
will go well.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Sun, Aug 13, 201
25 to 30.
If I went long term cruising I would like to have a boat like the Amel.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Aug 2, 2017 4:27 PM, "Josh Muckley via CnC-List"
wrote:
> TARTAN 3700 is very similar to 37+ or 37/40
>
> Hunter Legend series are well appoi
til the windows need replacing again, how will I be able to remove
one if the tape is "permanent".
Any other suggestions about the use of the tape will be appreciated.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
This list is supported
I am finally going replace one of my long ports. I wrote down 2 numbers
suggested by you listers. Vbh 4991 & 5952. Which one is preferred?
Also, where to buy, Amazon?
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
This list is supporte
I can tell you from personal experience that AGMs won't servive either. I
had 4 hooked in parallel that I flattened to 4.5 v . A painful
experience. At the same time I lost my inverter charger.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Jul 20, 2017 12:34 PM, "Bill Bina - gmai
Dave I have a pair Bose cube speakers that put out great sound and are
surface mounted.
Fred Hazzard
S/V Fury
C&C 44
On Jul 3, 2017 12:03 PM, "Leslie Paal via CnC-List"
wrote:
- if the amp is expecting 4 ohms load it will not drive the 8 ohms load to
full volume.
- the 30+ ye
As an owner of a 1986 44 I am very interested in the results of the survey
on your 44. I have had mine for 10 yrs and all is good.
Feel free to ask me questions.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Jul 1, 2017 7:36 PM, "Dan via CnC-List" wrote:
> I already did tha
I found scrubbing bubbles at Whale Mart.
Fred Hazzard
S/V Fury
C&C 44
Portland. Or
On Jun 7, 2017 1:22 PM, "Dennis C. via CnC-List"
wrote:
> While now exactly C&C related, this may provide help to some lister.
>
> I previously posted about cleaning my old NACRA bea
I just got a deal on a Garmin 5208 plotter. When I look to find a pod to
use at the binacle I find prices much higher than I paid for the plotter.
Looking for suggestions where to find something reasonable,
Fred Hazzard
S/V Fury
C&C 44
Portland
A little off topic but what do you use to recondition and polish the
plastic windows in a dodger?
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
On Thu, Apr 13, 2017 at 11:15 AM, Josh Muckley via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hard carnuba waxes typically get the highest rat
.
Fred Hazzard
S/V Fury
C&C 44
Portland, Or
___
This list is supported by the generous donations of our members. If you wish to
make a contribution to offset our costs, please go to:
https://www.paypal.me/stumurray
All Contributions are greatly appreciated!
1 - 100 of 257 matches
Mail list logo