If you all cant get it hooked up to transfer, Ill send my shipping billing number and Ill take the stuff otherwise have fun with it Joe..
JP [email protected] <mailto:[email protected]> From: CnC-List [mailto:[email protected]] On Behalf Of Gary Nylander Sent: Thursday, November 21, 2013 1:21 PM To: [email protected] Subject: Re: Stus-List Datamarine stuff FREE Joe, where are you? I have to go from St. Michaels to Annapolis tomorrow...... Gary ----- Original Message ----- From: Della Barba, Joe <mailto:[email protected]> To: [email protected] <mailto:[email protected]> Sent: Thursday, November 21, 2013 9:11 AM Subject: Re: Stus-List Datamarine stuff FREE Ill take it! Joe Della Barba Coquina THANKS!!!!!!!!!!! From: CnC-List [mailto:[email protected]] On Behalf Of Gary Nylander Sent: Thursday, November 21, 2013 9:01 AM To: [email protected] <mailto:[email protected]> Subject: Stus-List Datamarine stuff FREE I have a Datamarine Link 5100 system - appears to be complete. Came from my SO's late sister - must have been taken out before they upgraded and embarked on a voyage south. Datamarine 5100 control head, Display unit with digital speed and depth, analog wind; DX111 depth, SX 120 speed, wind speed/direction mast top unit, coax cable, through hull speed and depth sensors.... Yours for the cost of shipping, I have no need. Gary Nylander Maryland ----- Original Message ----- From: Robert Abbott <mailto:[email protected]> To: [email protected] <mailto:[email protected]> Sent: Wednesday, November 20, 2013 9:13 AM Subject: Stus-List Muffler John: I replaced the SS muffler this past Spring.....don't remember the exact measurements put similar to yours. I replaced it with a Vernalift resin muffler....slightly bigger (2" higher) muffler but with the same 2" inlet and 1 1/2" outlet. I will try to find my receipt which will have the part # if that helps you. Bottom line, Vernalift makes a resin muffler with a 1/1/2" outlet. I didn't want to get into adding hose adapters as my exhaust hoes was replaced last year and it is 1 1/2". There are no back pressure issues to worry about with the 1 1/2" outlet with these small marine diesel engines. Bob Abbott AZURA C&C 32 - 84 Halifax, N.S. On 2013/11/20 9:00 AM, John and Maryann Read wrote: The stainless muffler has finally given up the ghost. It is 6 ¼ round, 2 inch side inlet and 1 ½ inch top outlet, 9 inches high and the base is 7 inches square. Any suggested sources?? Vernalift by Centek Industries makes a close copy but the outlet is 2 inch. On a related note, any thoughts on why the outlet is smaller than the inlet and does this create any backpressure issues?? The engine outlet is 2 inch. On the other hand, this set up has worked well for 30 years so it cant be all bad :) TIA John and Maryann Legacy III 1982 C&C 34 Noank, CT _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com [email protected] <mailto:[email protected]> _____ _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com [email protected] <mailto:[email protected]> _____ _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com [email protected] <mailto:[email protected]>
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com [email protected]
