Gary: If there are no other takers, I'll take it as a give-away to someone who has boat but 0 bucks. I know a few...;)
Rich > On Nov 21, 2013, at 10:08, "dwight" <dwight...@gmail.com> wrote: > > Very nice gesture Gary; hopefully someone will find it useful > > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Gary > Nylander > Sent: November 21, 2013 10:01 AM > To: cnc-list@cnc-list.com > Subject: Stus-List Datamarine stuff FREE > > I have a Datamarine Link 5100 system - appears to be complete. Came from my > SO's late sister - must have been taken out before they upgraded and embarked > on a voyage south. > > Datamarine 5100 control head, Display unit with digital speed and depth, > analog wind; DX111 depth, SX 120 speed, wind speed/direction mast top unit, > coax cable, through hull speed and depth sensors.... > > Yours for the cost of shipping, I have no need. > > Gary Nylander > Maryland > > > ----- Original Message ----- > From: Robert Abbott > To: cnc-list@cnc-list.com > Sent: Wednesday, November 20, 2013 9:13 AM > Subject: Stus-List Muffler > > John: > > I replaced the SS muffler this past Spring.....don't remember the exact > measurements put similar to yours. > > I replaced it with a Vernalift resin muffler....slightly bigger (2" higher) > muffler but with the same 2" inlet and 1 1/2" outlet. I will try to find my > receipt which will have the part # if that helps you. Bottom line, Vernalift > makes a resin muffler with a 1/1/2" outlet. I didn't want to get into adding > hose adapters as my exhaust hoes was replaced last year and it is 1 1/2". > There are no back pressure issues to worry about with the 1 1/2" outlet with > these small marine diesel engines. > > Bob Abbott > AZURA > C&C 32 - 84 > Halifax, N.S. > > > > > > > > >> On 2013/11/20 9:00 AM, John and Maryann Read wrote: >> The stainless muffler has finally given up the ghost. It is 6 ¼ round, 2 >> inch side inlet and 1 ½ inch top outlet, 9 inches high and the base is 7 >> inches square. Any suggested sources?? Vernalift by Centek Industries >> makes a close copy but the outlet is 2 inch. On a related note, any >> thoughts on why the outlet is smaller than the inlet and does this create >> any backpressure issues?? The engine outlet is 2 inch. On the other hand, >> this set up has worked well for 30 years so it can’t be all bad J >> TIA >> John and Maryann >> Legacy III >> 1982 C&C 34 >> Noank, CT >> >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > No virus found in this message. > Checked by AVG - www.avg.com > Version: 2012.0.2247 / Virus Database: 3629/6354 - Release Date: 11/21/13 > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
