Hi Konstantin, Can you please attach the picture of the back label?
Regards, Nate Temple > On Aug 8, 2017, at 12:29 PM, Matheou, Konstantin J. (GRC-LCI0)[ZIN > TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: > > I am wearing my reading glasses and the letters were very small too... > > I took the picture and zoomed in on it with my phone.. > > It is 3117FF1.... > > > > -----Original Message----- > From: Nate Temple [mailto:nate.tem...@ettus.com] > Sent: Tuesday, August 08, 2017 3:25 PM > To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > <konstantin.j.math...@nasa.gov> > Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users > <usrp-users@lists.ettus.com> > Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue > > Hi Konstantin, > > Also, looking up the serial number 8117FF1 didn't not result in any matches. > > Can you please send a picture of the back label so we can clearly see the > numbers on the label? > > > Regards, > Nate Temple > > > > >> On Aug 8, 2017, at 12:23 PM, Nate Temple <nate.tem...@ettus.com> wrote: >> >> Hi Konstantin, >> >> The partition table looks like it is OK. >> >> I would suggest trying to redownload the release-4 / SpeedGrade3 images >> again and try burning them to the SD Card again. Verify that the md5sums >> match what is posted in the SG3/ folder. >> >> The error you're seeing has only came up when the incorrect SpeedGrade image >> is used. >> >> Regards, >> Nate Temple >> >> >> >> >>> On Aug 8, 2017, at 11:59 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >>> >>> Nate, >>> >>> I hope there is no issue with the hardware... OK.. we are now in debug mode >>> I guess... I hope you can hang out a little quicker with me to get this >>> resolved... I appreciate it... >>> >>> Below is the Disk Management program screen shot and I placed the files >>> that got placed on the micro SD card.... Again it was the file from >>> release4/...sg3/ - again I have the E310 E. >>> >>> This is the backup micro SD card…. And the micro SD card that came with >>> the unit (visually checked) looked exactly the same…. >>> >>> <image001.jpg> >>> >>> >>> >>> >>> -----Original Message----- >>> From: Nate Temple [mailto:nate.tem...@ettus.com] >>> Sent: Tuesday, August 08, 2017 2:35 PM >>> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>> <konstantin.j.math...@nasa.gov> >>> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users >>> <usrp-users@lists.ettus.com> >>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >>> >>> Hi Konstantin, >>> >>> I don't suspect that there is any issue at all with the hardware. It is >>> most likely due to the image or partition table on the SD card not being >>> setup correctly. >>> >>> Can you please open the Disk Management program within Windows and with the >>> SD card inserted, take a screen capture of the partition layout for the SD >>> Card? >>> >>> Regards, >>> Nate Temple >>> >>>> On Aug 8, 2017, at 11:16 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >>>> >>>> Nate, >>>> >>>> I also tried release 4 sg1 directory dev.direct file... same error as >>>> below... >>>> >>>> I also tried release 3 dev.direct... Was able to log in through root... >>>> made the vi alterations to the interfaces file... but was unable to >>>> ping... >>>> >>>> Here is the E310 info: >>>> >>>> P/N 156333E-01L >>>> >>>> S/N 8117FF1 >>>> >>>> How soon can I get another E310 shipped to me??? Unfortunately, I need to >>>> have a design ready for my project by early September. I really need a >>>> replacement pretty fast, if possible? >>>> >>>> Thanks, >>>> >>>> Konstantin >>>> >>>> -----Original Message----- >>>> From: Nate Temple [mailto:nate.tem...@ettus.com] >>>> Sent: Tuesday, August 08, 2017 1:21 PM >>>> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>>> <konstantin.j.math...@nasa.gov> >>>> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users >>>> <usrp-users@lists.ettus.com> >>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>> >>>> Hi Konstantin, >>>> >>>> Can you please send the full part number and serial number for your >>>> device. It is located on the label on the bottom side of the E3xx. ( "P/N: >>>> XXXXXX", "S/N: XXXXXXX" ) >>>> >>>> Regards, >>>> Nate Temple >>>> >>>> >>>>> On Aug 8, 2017, at 8:33 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >>>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >>>>> >>>>> OK… Used the backup microSD we ordered. Reprogrammed it with the same >>>>> .direct file… Same error as below… >>>>> >>>>> “Unable to read file uImage-zynq-e31x-3.dtb” >>>>> >>>>> Now, either I am loading a incorrect image, or something is not working >>>>> correctly with the unit. >>>>> >>>>> Please tell me your thoughts… >>>>> >>>>> Thanks… >>>>> >>>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>>>> Sent: Tuesday, August 08, 2017 11:29 AM >>>>> To: 'Nate Temple' <nate.tem...@ettus.com>; 'Marcus Müller' >>>>> <marcus.muel...@ettus.com> >>>>> Cc: 'usrp-users' <usrp-users@lists.ettus.com> >>>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>>> >>>>> Btw.. just to validate what image I used… >>>>> >>>>> I have the E310 E version… >>>>> >>>>> The instructions I think may not be correct… Here they are cut and >>>>> paste… Please validate…. >>>>> >>>>> For the E310, the product number will be 156333X-01L, where X is a letter >>>>> from A to Z. For devices where X is A, B, C, D, the images under the >>>>> "ettus-e3xx-sg1" folder should be used. For devices where X is E or >>>>> later, the images under the "ettus-e3xx-sg3" folder should be used. (WHAT >>>>> I USED) You must use the appropriate image for your specific device. The >>>>> incorrect image will not work, and will only boot as far as the U-Boot >>>>> boot loader before stopping. >>>>> >>>>> >>>>> >>>>> BUT this is what is written also… >>>>> >>>>> >>>>> >>>>> For the E312, the product number will be 140605X-01L, where X is a letter >>>>> from A to Z. The images under the "ettus-e3xx-sg3" folder should be used >>>>> for all E312 devices. >>>>> >>>>> >>>>> So you told me to go to release 4 (also the directions did)… and then I >>>>> chose the sg3 directory – Is this correct??? Thus, both the E310 E and >>>>> E312 devices use the sg3 directory???? >>>>> >>>>> I used the Ettus-3xx-sg3 directory and downloaded those versions. I am >>>>> assuming they are the correct versions. >>>>> >>>>> Thanks… >>>>> >>>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>>>> Sent: Tuesday, August 08, 2017 11:15 AM >>>>> To: 'Nate Temple' <nate.tem...@ettus.com>; Marcus Müller >>>>> <marcus.muel...@ettus.com> >>>>> Cc: usrp-users <usrp-users@lists.ettus.com> >>>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>>> >>>>> Nate, >>>>> >>>>> The instructions are very well written and detailed.. Thanks… >>>>> >>>>> Actually, most of the steps I was doing correctly from all the various >>>>> portions of documents. But it is good you placed all in one document. >>>>> Thanks… >>>>> >>>>> Everything worked well up until I burned the image. >>>>> >>>>> When I did the terminal command - sudo screen /dev/ttyUSB0 115200 – and >>>>> then turned on the E310, I received “Unable to read file >>>>> uImage-zynq-e31x-3.dtb” >>>>> >>>>> I tried both tx version – demo and dev… Both did the same thing… >>>>> >>>>> I have another SD card that we ordered with the unit. I will try to >>>>> re-image that card and see hwat happens… Of course, I will let you know. >>>>> >>>>> Thanks, >>>>> >>>>> Konstantin >>>>> >>>>> From: Nate Temple [mailto:nate.tem...@ettus.com] >>>>> Sent: Monday, August 07, 2017 9:29 PM >>>>> To: Marcus Müller <marcus.muel...@ettus.com> >>>>> Cc: usrp-users <usrp-users@lists.ettus.com>; Matheou, Konstantin J. >>>>> (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> >>>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>>> >>>>> Hi Konstantin, >>>>> >>>>> Please see the updated version of the PDF, attached to this email. One of >>>>> the screen captures needed to be updated. >>>>> >>>>> Regards, >>>>> Nate Temple >>>>> >>>>> >>>>> >>>>> >>>>> Previous message >>>>> ------------------------------- >>>>> Hi Konstantin, >>>>> >>>>> I had an error in my previous email. The default setting for the >>>>> release-4 image is to have a DHCP address. You'll need to edit >>>>> /etc/network/interfaces and update it to operate with a static IP. >>>>> >>>>> Please see the attached PDF that will walk through the process of burning >>>>> the release-4 SD Card image to a blank SD Card, and then the required >>>>> steps to configure the Ubuntu VM within the Windows host to connect via >>>>> the Serial interface to update the /etc/network/interfaces file, and then >>>>> connect via SSH. >>>>> >>>>> Also, with 1GbE connections, you do not need to use a cross over cable. >>>>> 1GbE has auto-MDIX which will allow a normal straight through ethernet >>>>> cable to be used when directly connecting devices. >>>>> >>>>> Regards, >>>>> Nate Temple >>>>> ------------------------------- >>>> >> > _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
