Hi Konstantin, The partition table looks like it is OK.
I would suggest trying to redownload the release-4 / SpeedGrade3 images again and try burning them to the SD Card again. Verify that the md5sums match what is posted in the SG3/ folder. The error you're seeing has only came up when the incorrect SpeedGrade image is used. Regards, Nate Temple > On Aug 8, 2017, at 11:59 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN > TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: > > Nate, > > I hope there is no issue with the hardware... OK.. we are now in debug mode I > guess... I hope you can hang out a little quicker with me to get this > resolved... I appreciate it... > > Below is the Disk Management program screen shot and I placed the files that > got placed on the micro SD card.... Again it was the file from > release4/...sg3/ - again I have the E310 E. > > This is the backup micro SD card…. And the micro SD card that came with the > unit (visually checked) looked exactly the same…. > > <image001.jpg> > > > > > -----Original Message----- > From: Nate Temple [mailto:nate.tem...@ettus.com] > Sent: Tuesday, August 08, 2017 2:35 PM > To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > <konstantin.j.math...@nasa.gov> > Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users > <usrp-users@lists.ettus.com> > Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue > > Hi Konstantin, > > I don't suspect that there is any issue at all with the hardware. It is most > likely due to the image or partition table on the SD card not being setup > correctly. > > Can you please open the Disk Management program within Windows and with the > SD card inserted, take a screen capture of the partition layout for the SD > Card? > > Regards, > Nate Temple > > > On Aug 8, 2017, at 11:16 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN > > TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: > > > > Nate, > > > > I also tried release 4 sg1 directory dev.direct file... same error as > > below... > > > > I also tried release 3 dev.direct... Was able to log in through root... > > made the vi alterations to the interfaces file... but was unable to ping... > > > > Here is the E310 info: > > > > P/N 156333E-01L > > > > S/N 8117FF1 > > > > How soon can I get another E310 shipped to me??? Unfortunately, I need to > > have a design ready for my project by early September. I really need a > > replacement pretty fast, if possible? > > > > Thanks, > > > > Konstantin > > > > -----Original Message----- > > From: Nate Temple [mailto:nate.tem...@ettus.com] > > Sent: Tuesday, August 08, 2017 1:21 PM > > To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > > <konstantin.j.math...@nasa.gov> > > Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users > > <usrp-users@lists.ettus.com> > > Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue > > > > Hi Konstantin, > > > > Can you please send the full part number and serial number for your device. > > It is located on the label on the bottom side of the E3xx. ( "P/N: XXXXXX", > > "S/N: XXXXXXX" ) > > > > Regards, > > Nate Temple > > > > > >> On Aug 8, 2017, at 8:33 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN > >> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: > >> > >> OK… Used the backup microSD we ordered. Reprogrammed it with the same > >> .direct file… Same error as below… > >> > >> “Unable to read file uImage-zynq-e31x-3.dtb” > >> > >> Now, either I am loading a incorrect image, or something is not working > >> correctly with the unit. > >> > >> Please tell me your thoughts… > >> > >> Thanks… > >> > >> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > >> Sent: Tuesday, August 08, 2017 11:29 AM > >> To: 'Nate Temple' <nate.tem...@ettus.com>; 'Marcus Müller' > >> <marcus.muel...@ettus.com> > >> Cc: 'usrp-users' <usrp-users@lists.ettus.com> > >> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue > >> > >> Btw.. just to validate what image I used… > >> > >> I have the E310 E version… > >> > >> The instructions I think may not be correct… Here they are cut and paste… > >> Please validate…. > >> > >> For the E310, the product number will be 156333X-01L, where X is a letter > >> from A to Z. For devices where X is A, B, C, D, the images under the > >> "ettus-e3xx-sg1" folder should be used. For devices where X is E or later, > >> the images under the "ettus-e3xx-sg3" folder should be used. (WHAT I USED) > >> You must use the appropriate image for your specific device. The incorrect > >> image will not work, and will only boot as far as the U-Boot boot loader > >> before stopping. > >> > >> > >> > >> BUT this is what is written also… > >> > >> > >> > >> For the E312, the product number will be 140605X-01L, where X is a letter > >> from A to Z. The images under the "ettus-e3xx-sg3" folder should be used > >> for all E312 devices. > >> > >> > >> So you told me to go to release 4 (also the directions did)… and then I > >> chose the sg3 directory – Is this correct??? Thus, both the E310 E and > >> E312 devices use the sg3 directory???? > >> > >> I used the Ettus-3xx-sg3 directory and downloaded those versions. I am > >> assuming they are the correct versions. > >> > >> Thanks… > >> > >> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > >> Sent: Tuesday, August 08, 2017 11:15 AM > >> To: 'Nate Temple' <nate.tem...@ettus.com>; Marcus Müller > >> <marcus.muel...@ettus.com> > >> Cc: usrp-users <usrp-users@lists.ettus.com> > >> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue > >> > >> Nate, > >> > >> The instructions are very well written and detailed.. Thanks… > >> > >> Actually, most of the steps I was doing correctly from all the various > >> portions of documents. But it is good you placed all in one document. > >> Thanks… > >> > >> Everything worked well up until I burned the image. > >> > >> When I did the terminal command - sudo screen /dev/ttyUSB0 115200 – and > >> then turned on the E310, I received “Unable to read file > >> uImage-zynq-e31x-3.dtb” > >> > >> I tried both tx version – demo and dev… Both did the same thing… > >> > >> I have another SD card that we ordered with the unit. I will try to > >> re-image that card and see hwat happens… Of course, I will let you know. > >> > >> Thanks, > >> > >> Konstantin > >> > >> From: Nate Temple [mailto:nate.tem...@ettus.com] > >> Sent: Monday, August 07, 2017 9:29 PM > >> To: Marcus Müller <marcus.muel...@ettus.com> > >> Cc: usrp-users <usrp-users@lists.ettus.com>; Matheou, Konstantin J. > >> (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> > >> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue > >> > >> Hi Konstantin, > >> > >> Please see the updated version of the PDF, attached to this email. One of > >> the screen captures needed to be updated. > >> > >> Regards, > >> Nate Temple > >> > >> > >> > >> > >> Previous message > >> ------------------------------- > >> Hi Konstantin, > >> > >> I had an error in my previous email. The default setting for the release-4 > >> image is to have a DHCP address. You'll need to edit > >> /etc/network/interfaces and update it to operate with a static IP. > >> > >> Please see the attached PDF that will walk through the process of burning > >> the release-4 SD Card image to a blank SD Card, and then the required > >> steps to configure the Ubuntu VM within the Windows host to connect via > >> the Serial interface to update the /etc/network/interfaces file, and then > >> connect via SSH. > >> > >> Also, with 1GbE connections, you do not need to use a cross over cable. > >> 1GbE has auto-MDIX which will allow a normal straight through ethernet > >> cable to be used when directly connecting devices. > >> > >> Regards, > >> Nate Temple > >> ------------------------------- > > _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
