Hi Konstantin, Can you please send the full part number and serial number for your device. It is located on the label on the bottom side of the E3xx. ( "P/N: XXXXXX", "S/N: XXXXXXX" )
Regards, Nate Temple > On Aug 8, 2017, at 8:33 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN > TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: > > OK… Used the backup microSD we ordered. Reprogrammed it with the same > .direct file… Same error as below… > > “Unable to read file uImage-zynq-e31x-3.dtb” > > Now, either I am loading a incorrect image, or something is not working > correctly with the unit. > > Please tell me your thoughts… > > Thanks… > > From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > Sent: Tuesday, August 08, 2017 11:29 AM > To: 'Nate Temple' <nate.tem...@ettus.com>; 'Marcus Müller' > <marcus.muel...@ettus.com> > Cc: 'usrp-users' <usrp-users@lists.ettus.com> > Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue > > Btw.. just to validate what image I used… > > I have the E310 E version… > > The instructions I think may not be correct… Here they are cut and paste… > Please validate…. > > For the E310, the product number will be 156333X-01L, where X is a letter > from A to Z. For devices where X is A, B, C, D, the images under the > "ettus-e3xx-sg1" folder should be used. For devices where X is E or later, > the images under the "ettus-e3xx-sg3" folder should be used. (WHAT I USED) > You must use the appropriate image for your specific device. The incorrect > image will not work, and will only boot as far as the U-Boot boot loader > before stopping. > > > > BUT this is what is written also… > > > > For the E312, the product number will be 140605X-01L, where X is a letter > from A to Z. The images under the "ettus-e3xx-sg3" folder should be used for > all E312 devices. > > > So you told me to go to release 4 (also the directions did)… and then I > chose the sg3 directory – Is this correct??? Thus, both the E310 E and E312 > devices use the sg3 directory???? > > I used the Ettus-3xx-sg3 directory and downloaded those versions. I am > assuming they are the correct versions. > > Thanks… > > From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] > Sent: Tuesday, August 08, 2017 11:15 AM > To: 'Nate Temple' <nate.tem...@ettus.com>; Marcus Müller > <marcus.muel...@ettus.com> > Cc: usrp-users <usrp-users@lists.ettus.com> > Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue > > Nate, > > The instructions are very well written and detailed.. Thanks… > > Actually, most of the steps I was doing correctly from all the various > portions of documents. But it is good you placed all in one document. > Thanks… > > Everything worked well up until I burned the image. > > When I did the terminal command - sudo screen /dev/ttyUSB0 115200 – and then > turned on the E310, I received “Unable to read file uImage-zynq-e31x-3.dtb” > > I tried both tx version – demo and dev… Both did the same thing… > > I have another SD card that we ordered with the unit. I will try to re-image > that card and see hwat happens… Of course, I will let you know. > > Thanks, > > Konstantin > > From: Nate Temple [mailto:nate.tem...@ettus.com] > Sent: Monday, August 07, 2017 9:29 PM > To: Marcus Müller <marcus.muel...@ettus.com> > Cc: usrp-users <usrp-users@lists.ettus.com>; Matheou, Konstantin J. > (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> > Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue > > Hi Konstantin, > > Please see the updated version of the PDF, attached to this email. One of the > screen captures needed to be updated. > > Regards, > Nate Temple > > > > > Previous message > ------------------------------- > Hi Konstantin, > > I had an error in my previous email. The default setting for the release-4 > image is to have a DHCP address. You'll need to edit /etc/network/interfaces > and update it to operate with a static IP. > > Please see the attached PDF that will walk through the process of burning the > release-4 SD Card image to a blank SD Card, and then the required steps to > configure the Ubuntu VM within the Windows host to connect via the Serial > interface to update the /etc/network/interfaces file, and then connect via > SSH. > > Also, with 1GbE connections, you do not need to use a cross over cable. 1GbE > has auto-MDIX which will allow a normal straight through ethernet cable to be > used when directly connecting devices. > > Regards, > Nate Temple > ------------------------------- _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
