I am wearing my reading glasses and the letters were very small too... I took the picture and zoomed in on it with my phone..
It is 3117FF1.... -----Original Message----- From: Nate Temple [mailto:nate.tem...@ettus.com] Sent: Tuesday, August 08, 2017 3:25 PM To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users <usrp-users@lists.ettus.com> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue Hi Konstantin, Also, looking up the serial number 8117FF1 didn't not result in any matches. Can you please send a picture of the back label so we can clearly see the numbers on the label? Regards, Nate Temple > On Aug 8, 2017, at 12:23 PM, Nate Temple <nate.tem...@ettus.com> wrote: > > Hi Konstantin, > > The partition table looks like it is OK. > > I would suggest trying to redownload the release-4 / SpeedGrade3 images again > and try burning them to the SD Card again. Verify that the md5sums match what > is posted in the SG3/ folder. > > The error you're seeing has only came up when the incorrect SpeedGrade image > is used. > > Regards, > Nate Temple > > > > >> On Aug 8, 2017, at 11:59 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >> >> Nate, >> >> I hope there is no issue with the hardware... OK.. we are now in debug mode >> I guess... I hope you can hang out a little quicker with me to get this >> resolved... I appreciate it... >> >> Below is the Disk Management program screen shot and I placed the files that >> got placed on the micro SD card.... Again it was the file from >> release4/...sg3/ - again I have the E310 E. >> >> This is the backup micro SD card…. And the micro SD card that came with the >> unit (visually checked) looked exactly the same…. >> >> <image001.jpg> >> >> >> >> >> -----Original Message----- >> From: Nate Temple [mailto:nate.tem...@ettus.com] >> Sent: Tuesday, August 08, 2017 2:35 PM >> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >> <konstantin.j.math...@nasa.gov> >> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users >> <usrp-users@lists.ettus.com> >> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >> >> Hi Konstantin, >> >> I don't suspect that there is any issue at all with the hardware. It is most >> likely due to the image or partition table on the SD card not being setup >> correctly. >> >> Can you please open the Disk Management program within Windows and with the >> SD card inserted, take a screen capture of the partition layout for the SD >> Card? >> >> Regards, >> Nate Temple >> >>> On Aug 8, 2017, at 11:16 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >>> >>> Nate, >>> >>> I also tried release 4 sg1 directory dev.direct file... same error as >>> below... >>> >>> I also tried release 3 dev.direct... Was able to log in through root... >>> made the vi alterations to the interfaces file... but was unable to ping... >>> >>> Here is the E310 info: >>> >>> P/N 156333E-01L >>> >>> S/N 8117FF1 >>> >>> How soon can I get another E310 shipped to me??? Unfortunately, I need to >>> have a design ready for my project by early September. I really need a >>> replacement pretty fast, if possible? >>> >>> Thanks, >>> >>> Konstantin >>> >>> -----Original Message----- >>> From: Nate Temple [mailto:nate.tem...@ettus.com] >>> Sent: Tuesday, August 08, 2017 1:21 PM >>> To: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>> <konstantin.j.math...@nasa.gov> >>> Cc: Marcus Müller <marcus.muel...@ettus.com>; usrp-users >>> <usrp-users@lists.ettus.com> >>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >>> >>> Hi Konstantin, >>> >>> Can you please send the full part number and serial number for your device. >>> It is located on the label on the bottom side of the E3xx. ( "P/N: XXXXXX", >>> "S/N: XXXXXXX" ) >>> >>> Regards, >>> Nate Temple >>> >>> >>>> On Aug 8, 2017, at 8:33 AM, Matheou, Konstantin J. (GRC-LCI0)[ZIN >>>> TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> wrote: >>>> >>>> OK… Used the backup microSD we ordered. Reprogrammed it with the same >>>> .direct file… Same error as below… >>>> >>>> “Unable to read file uImage-zynq-e31x-3.dtb” >>>> >>>> Now, either I am loading a incorrect image, or something is not working >>>> correctly with the unit. >>>> >>>> Please tell me your thoughts… >>>> >>>> Thanks… >>>> >>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>>> Sent: Tuesday, August 08, 2017 11:29 AM >>>> To: 'Nate Temple' <nate.tem...@ettus.com>; 'Marcus Müller' >>>> <marcus.muel...@ettus.com> >>>> Cc: 'usrp-users' <usrp-users@lists.ettus.com> >>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>> >>>> Btw.. just to validate what image I used… >>>> >>>> I have the E310 E version… >>>> >>>> The instructions I think may not be correct… Here they are cut and paste… >>>> Please validate…. >>>> >>>> For the E310, the product number will be 156333X-01L, where X is a letter >>>> from A to Z. For devices where X is A, B, C, D, the images under the >>>> "ettus-e3xx-sg1" folder should be used. For devices where X is E or later, >>>> the images under the "ettus-e3xx-sg3" folder should be used. (WHAT I USED) >>>> You must use the appropriate image for your specific device. The incorrect >>>> image will not work, and will only boot as far as the U-Boot boot loader >>>> before stopping. >>>> >>>> >>>> >>>> BUT this is what is written also… >>>> >>>> >>>> >>>> For the E312, the product number will be 140605X-01L, where X is a letter >>>> from A to Z. The images under the "ettus-e3xx-sg3" folder should be used >>>> for all E312 devices. >>>> >>>> >>>> So you told me to go to release 4 (also the directions did)… and then I >>>> chose the sg3 directory – Is this correct??? Thus, both the E310 E and >>>> E312 devices use the sg3 directory???? >>>> >>>> I used the Ettus-3xx-sg3 directory and downloaded those versions. I am >>>> assuming they are the correct versions. >>>> >>>> Thanks… >>>> >>>> From: Matheou, Konstantin J. (GRC-LCI0)[ZIN TECHNOLOGIES INC] >>>> Sent: Tuesday, August 08, 2017 11:15 AM >>>> To: 'Nate Temple' <nate.tem...@ettus.com>; Marcus Müller >>>> <marcus.muel...@ettus.com> >>>> Cc: usrp-users <usrp-users@lists.ettus.com> >>>> Subject: RE: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>> >>>> Nate, >>>> >>>> The instructions are very well written and detailed.. Thanks… >>>> >>>> Actually, most of the steps I was doing correctly from all the various >>>> portions of documents. But it is good you placed all in one document. >>>> Thanks… >>>> >>>> Everything worked well up until I burned the image. >>>> >>>> When I did the terminal command - sudo screen /dev/ttyUSB0 115200 – and >>>> then turned on the E310, I received “Unable to read file >>>> uImage-zynq-e31x-3.dtb” >>>> >>>> I tried both tx version – demo and dev… Both did the same thing… >>>> >>>> I have another SD card that we ordered with the unit. I will try to >>>> re-image that card and see hwat happens… Of course, I will let you know. >>>> >>>> Thanks, >>>> >>>> Konstantin >>>> >>>> From: Nate Temple [mailto:nate.tem...@ettus.com] >>>> Sent: Monday, August 07, 2017 9:29 PM >>>> To: Marcus Müller <marcus.muel...@ettus.com> >>>> Cc: usrp-users <usrp-users@lists.ettus.com>; Matheou, Konstantin J. >>>> (GRC-LCI0)[ZIN TECHNOLOGIES INC] <konstantin.j.math...@nasa.gov> >>>> Subject: Re: [USRP-users] When ssh'ing Getting prompt for Password Issue >>>> >>>> Hi Konstantin, >>>> >>>> Please see the updated version of the PDF, attached to this email. One of >>>> the screen captures needed to be updated. >>>> >>>> Regards, >>>> Nate Temple >>>> >>>> >>>> >>>> >>>> Previous message >>>> ------------------------------- >>>> Hi Konstantin, >>>> >>>> I had an error in my previous email. The default setting for the release-4 >>>> image is to have a DHCP address. You'll need to edit >>>> /etc/network/interfaces and update it to operate with a static IP. >>>> >>>> Please see the attached PDF that will walk through the process of burning >>>> the release-4 SD Card image to a blank SD Card, and then the required >>>> steps to configure the Ubuntu VM within the Windows host to connect via >>>> the Serial interface to update the /etc/network/interfaces file, and then >>>> connect via SSH. >>>> >>>> Also, with 1GbE connections, you do not need to use a cross over cable. >>>> 1GbE has auto-MDIX which will allow a normal straight through ethernet >>>> cable to be used when directly connecting devices. >>>> >>>> Regards, >>>> Nate Temple >>>> ------------------------------- >>> > _______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
