Please share the same
From: Edgar Mauricio Diaz Orellana [mailto:[email protected]] Sent: 28 February 2012 18:57 To: Joe Danrich Cc: Pradip; [email protected] Subject: Re: [OSL | CCIE_RS] Dynamips / GNS3 64 Bit for my local lan i had an 4006 with supervisor engine IV, quite impressive machine with that supervisor, even IPv6 run flawless :-) with 3 power supplies (only 2 plugged on), anyway... enough power to play and still playing with my CCIE Lab :-) did you seek the website i'll mention to see the pics of my lab? On Tue, Feb 28, 2012 at 3:25 AM, Joe Danrich <[email protected]> wrote: Download the GNS3 off of the GNS websiite,, http://www.gns3.net/ To to the download link and grab the all in one package.. Then download the 64bit Windows 7 separately. Have you checked out the information on the IPExperts Blow on using their Dynmips .net files? Cheers Joe On 02/27/2012 08:01 AM, Pradip wrote: Dear All, I have below configuration in my laptop. Is this fine for working around 10 routers. I observed my laptop get hit near to palm where my hdd is location,,, is this fine or any issue?? Please let us know which gns3 and ios I can use to do practice for ccie lab.. Please share the gns3 and ios link Regards -- Pradip patole -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Joe Danrich Sent: 27 February 2012 10:38 To: Tim Miller Cc: [email protected] Subject: Re: [OSL | CCIE_RS] Dynamips / GNS3 64 Bit Guys appreciate the comments from everyone.. I did get the 64bit GNS3 to run very on my quad-core i7 laptop with 8GB RAM.. It appears so far to run more smoother than the 32bit on Windows 7.. I was able to tweak it and have the entire IPExperts Dynamips map running with about 35-40% of the overall CPU(s) being used at the most. So far this is initial without any IP Routing or the dreaded multi cast.. ;-) I setup separate hypervisors for each group of devices and in turn each of them had their own idle-pc.. So far so good.. Cheers Joe On 02/26/2012 08:27 PM, Tim Miller wrote: > I have no issues on Windows7 64bit and I can run the IPX topology with 10% CPU load on a cheap i5 laptop with an SSD. > - gotta use Idlemax and Idlepc values!!!! > I'm using the GNS virtual box edition. > > Sent from my iPhone > > On Feb 26, 2012, at 7:57 PM, Bob McCouch<[email protected]> wrote: > >> Windows also has per-process memory limits which cap you at 6-8 >> routers per hypervisor, requiring you to use multiple instances of >> Dynamips hypervisors. Linux doesn't have that restriction so you can >> run a single hypervisor. >> >> Sent from my iPad >> >> On Feb 26, 2012, at 9:48 PM, Max Kamali<[email protected]> wrote: >> >>> I use the windows version for quick/small tests ( no more than 5 virtual >>> routers) when I don't want to fire up my linux box. Cpu usage is higher >>> compared to linux. You may also run into issues with dynamips crashing when >>> booting about 8 or more routers, even with a boot-sequence delay. >>> >>> For heavy I'd recommend using linux. >>> >>> -max >>> >>> -----Original Message----- >>> From: [email protected] >>> [mailto:[email protected]] On Behalf Of Joe Danrich >>> Sent: Sunday, February 26, 2012 6:21 PM >>> To: [email protected] >>> Subject: [OSL | CCIE_RS] Dynamips / GNS3 64 Bit >>> >>> Hello Peoples >>> >>> So on Windows 7 has anyone tried the 64Bit version of Dynamips/GNS3 that is >>> available as a stand-alone download? >>> >>> If so, any good, bad or ugly? >>> >>> Ta >>> >>> Joe >>> >>> >>> >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please >>> visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>> >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com >> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs ----- No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.1913 / Virus Database: 2114/4835 - Release Date: 02/27/12 _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs -- Edgar Díaz Orellana CCENT/CCNA/CCNA Security, CCNP en progreso, CCSP pausado. Kaspersky Administrator / Technical Specialist Microsoft Certified Professional. Celular : 09-94118996 skype: eorellan1969 _____ No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.1913 / Virus Database: 2114/4835 - Release Date: 02/27/12 _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
