12 routers on my Dell Precision M6500, i7 and 16GB RAM, smooth on windows 2008r2 enterprice...
nothing to say, just idlemax 128.... just this tweak!, i could do almost every lab on GNS3, and then i'll pass everything on my 2800, 3800 routers and 3560 switches! :-) greetings. On Mon, Feb 27, 2012 at 2:14 AM, Joe Danrich <[email protected]> wrote: > I am running idlemax at 250 right now and once I get some routing > protocols running then I'll start tweaking it some more.. > > allegedly, adding routing protocols may not matter in the grand scheme of > things.. > > Ciao > > Joe > > > On 02/26/2012 09:10 PM, Tim Miller wrote: > >> You forgot Idlemax = 100 >> Place it right below your Idlepc setting in your .net file >> That should get CPU down further... >> >> Sent from my iPhone >> >> On Feb 26, 2012, at 10:07 PM, Joe Danrich<[email protected]> wrote: >> >> Guys appreciate the comments from everyone.. >>> >>> I did get the 64bit GNS3 to run very on my quad-core i7 laptop with 8GB >>> RAM.. >>> >>> It appears so far to run more smoother than the 32bit on Windows 7.. >>> >>> I was able to tweak it and have the entire IPExperts Dynamips map >>> running with about 35-40% of the overall CPU(s) being used at the most. So >>> far this is initial without any IP Routing or the dreaded multi cast.. ;-) >>> >>> I setup separate hypervisors for each group of devices and in turn each >>> of them had their own idle-pc.. So far so good.. >>> >>> Cheers >>> >>> Joe >>> >>> >>> >>> On 02/26/2012 08:27 PM, Tim Miller wrote: >>> >>>> I have no issues on Windows7 64bit and I can run the IPX topology with >>>> 10% CPU load on a cheap i5 laptop with an SSD. >>>> - gotta use Idlemax and Idlepc values!!!! >>>> I'm using the GNS virtual box edition. >>>> >>>> Sent from my iPhone >>>> >>>> On Feb 26, 2012, at 7:57 PM, Bob McCouch<[email protected]> wrote: >>>> >>>> Windows also has per-process memory limits which cap you at 6-8 >>>>> routers per hypervisor, requiring you to use multiple instances of >>>>> Dynamips hypervisors. Linux doesn't have that restriction so you can >>>>> run a single hypervisor. >>>>> >>>>> Sent from my iPad >>>>> >>>>> On Feb 26, 2012, at 9:48 PM, Max Kamali<[email protected]> wrote: >>>>> >>>>> I use the windows version for quick/small tests ( no more than 5 >>>>>> virtual >>>>>> routers) when I don't want to fire up my linux box. Cpu usage is >>>>>> higher >>>>>> compared to linux. You may also run into issues with dynamips >>>>>> crashing when >>>>>> booting about 8 or more routers, even with a boot-sequence delay. >>>>>> >>>>>> For heavy I'd recommend using linux. >>>>>> >>>>>> -max >>>>>> >>>>>> -----Original Message----- >>>>>> From: >>>>>> ccie_rs-bounces@**onlinestudylist.com<[email protected]> >>>>>> [mailto:ccie_rs-bounces@**onlinestudylist.com<[email protected]>] >>>>>> On Behalf Of Joe Danrich >>>>>> Sent: Sunday, February 26, 2012 6:21 PM >>>>>> To: [email protected] >>>>>> Subject: [OSL | CCIE_RS] Dynamips / GNS3 64 Bit >>>>>> >>>>>> Hello Peoples >>>>>> >>>>>> So on Windows 7 has anyone tried the 64Bit version of Dynamips/GNS3 >>>>>> that is >>>>>> available as a stand-alone download? >>>>>> >>>>>> If so, any good, bad or ugly? >>>>>> >>>>>> Ta >>>>>> >>>>>> Joe >>>>>> >>>>>> >>>>>> >>>>>> ______________________________**_________________ >>>>>> For more information regarding industry leading CCIE Lab training, >>>>>> please >>>>>> visit www.ipexpert.com >>>>>> >>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>> www.PlatinumPlacement.com >>>>>> >>>>>> http://onlinestudylist.com/**mailman/listinfo/ccie_rs<http://onlinestudylist.com/mailman/listinfo/ccie_rs> >>>>>> >>>>>> ______________________________**_________________ >>>>>> For more information regarding industry leading CCIE Lab training, >>>>>> please visit www.ipexpert.com >>>>>> >>>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>>> www.PlatinumPlacement.com >>>>>> >>>>>> http://onlinestudylist.com/**mailman/listinfo/ccie_rs<http://onlinestudylist.com/mailman/listinfo/ccie_rs> >>>>>> >>>>> ______________________________**_________________ >>>>> For more information regarding industry leading CCIE Lab training, >>>>> please visit www.ipexpert.com >>>>> >>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>> www.PlatinumPlacement.com >>>>> >>>>> http://onlinestudylist.com/**mailman/listinfo/ccie_rs<http://onlinestudylist.com/mailman/listinfo/ccie_rs> >>>>> >>>> ______________________________**_________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com >>>> >>>> http://onlinestudylist.com/**mailman/listinfo/ccie_rs<http://onlinestudylist.com/mailman/listinfo/ccie_rs> >>>> >>> > ______________________________**_________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/**mailman/listinfo/ccie_rs<http://onlinestudylist.com/mailman/listinfo/ccie_rs> > -- Edgar Díaz Orellana CCENT/CCNA/CCNA Security, CCNP en progreso, CCSP pausado. Kaspersky Administrator / Technical Specialist Microsoft Certified Professional. Celular : 09-94118996 skype: eorellan1969 _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
