You forgot Idlemax = 100 Place it right below your Idlepc setting in your .net file That should get CPU down further...
Sent from my iPhone On Feb 26, 2012, at 10:07 PM, Joe Danrich <[email protected]> wrote: > Guys appreciate the comments from everyone.. > > I did get the 64bit GNS3 to run very on my quad-core i7 laptop with 8GB RAM.. > > It appears so far to run more smoother than the 32bit on Windows 7.. > > I was able to tweak it and have the entire IPExperts Dynamips map running > with about 35-40% of the overall CPU(s) being used at the most. So far this > is initial without any IP Routing or the dreaded multi cast.. ;-) > > I setup separate hypervisors for each group of devices and in turn each of > them had their own idle-pc.. So far so good.. > > Cheers > > Joe > > > > On 02/26/2012 08:27 PM, Tim Miller wrote: >> I have no issues on Windows7 64bit and I can run the IPX topology with 10% >> CPU load on a cheap i5 laptop with an SSD. >> - gotta use Idlemax and Idlepc values!!!! >> I'm using the GNS virtual box edition. >> >> Sent from my iPhone >> >> On Feb 26, 2012, at 7:57 PM, Bob McCouch<[email protected]> wrote: >> >>> Windows also has per-process memory limits which cap you at 6-8 >>> routers per hypervisor, requiring you to use multiple instances of >>> Dynamips hypervisors. Linux doesn't have that restriction so you can >>> run a single hypervisor. >>> >>> Sent from my iPad >>> >>> On Feb 26, 2012, at 9:48 PM, Max Kamali<[email protected]> wrote: >>> >>>> I use the windows version for quick/small tests ( no more than 5 virtual >>>> routers) when I don't want to fire up my linux box. Cpu usage is higher >>>> compared to linux. You may also run into issues with dynamips crashing when >>>> booting about 8 or more routers, even with a boot-sequence delay. >>>> >>>> For heavy I'd recommend using linux. >>>> >>>> -max >>>> >>>> -----Original Message----- >>>> From: [email protected] >>>> [mailto:[email protected]] On Behalf Of Joe Danrich >>>> Sent: Sunday, February 26, 2012 6:21 PM >>>> To: [email protected] >>>> Subject: [OSL | CCIE_RS] Dynamips / GNS3 64 Bit >>>> >>>> Hello Peoples >>>> >>>> So on Windows 7 has anyone tried the 64Bit version of Dynamips/GNS3 that is >>>> available as a stand-alone download? >>>> >>>> If so, any good, bad or ugly? >>>> >>>> Ta >>>> >>>> Joe >>>> >>>> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, please >>>> visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com >>>> >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, please >>>> visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com >>>> >>>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >>> _______________________________________________ >>> For more information regarding industry leading CCIE Lab training, please >>> visit www.ipexpert.com >>> >>> Are you a CCNP or CCIE and looking for a job? Check out >>> www.PlatinumPlacement.com >>> >>> http://onlinestudylist.com/mailman/listinfo/ccie_rs >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out >> www.PlatinumPlacement.com >> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
