Sorry, here it is.

Benchmark rate summary:
  Num received samples:     5999986436
  Num dropped samples:      0
  Num overruns detected:    0
  Num transmitted samples:  0
  Num sequence errors (Tx): 0
  Num sequence errors (Rx): 0
  Num underruns detected:   0
  Num late commands:        0
  Num timeouts (Tx):        0
  Num timeouts (Rx):        0


On Wed, Jul 17, 2019 at 5:08 PM Nate Temple <nate.tem...@ettus.com> wrote:

> Hi Sumit,
>
> It will take 10 minutes for that run to complete. Does it produce a report
> at the end of the run?
>
> Regards,
> Nate Temple
>
> On Wed, Jul 17, 2019 at 8:06 AM Sumit Kumar <cog...@gmail.com> wrote:
>
>> Hi Nate,
>> No there are not. At the end of the last line, cursor keeps blinking, no
>> sequence errors.
>>
>> john@john-Precision-M4600:~/pybombs/src/uhd/host/build/examples$ sudo
>> ./benchmark_rate --rx_rate 10e6 --duration 600
>>
>> [INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>> UHD_3.15.0.git-1-gf83faf28
>> [00:00:00.000024] Creating the usrp device with: ...
>> [INFO] [USRP2] Opening a USRP2/N-Series device...
>> [INFO] [USRP2] Current recv frame size: 1472 bytes
>> [INFO] [USRP2] Current send frame size: 1472 bytes
>> Using Device: Single USRP:
>>   Device: USRP2 / N-Series Device
>>   Mboard 0: N200r4
>>   RX Channel: 0
>>     RX DSP: 0
>>     RX Dboard: A
>>     RX Subdev: SBXv3 RX
>>   TX Channel: 0
>>     TX DSP: 0
>>     TX Dboard: A
>>     TX Subdev: SBXv3 TX
>>
>> [00:00:01.796895] Setting device timestamp to 0...
>> [00:00:01.797430] Testing receive rate 10.000000 Msps on 1 channels
>>
>> On Wed, Jul 17, 2019 at 4:39 PM Nate Temple <nate.tem...@ettus.com>
>> wrote:
>>
>>> Hi Sumit,
>>>
>>> If you run benchmark_rate for an extend period of time, do you see any
>>> sequence errors?
>>>
>>> /usr/local/lib/uhd/examples/benchmark_rate --rx_rate 10e6 --duration 600
>>>
>>>
>>> Regards,
>>> Nate Temple
>>>
>>> On Wed, Jul 17, 2019 at 7:34 AM Sumit Kumar <cog...@gmail.com> wrote:
>>>
>>>> Hi Nate,
>>>> Yes I addressed the first 2 points you mentioned.
>>>>
>>>> john@john-Precision-M4600:~/pybombs/src/gnuradio/gr-digital/examples/narrowband$
>>>> sudo ./benchmark_tx.py -f 2.45G -S 10
>>>> linux; GNU C++ version 5.3.1 20151219; Boost_105800;
>>>> UHD_003.009.002-0-unknown
>>>>
>>>> Using Volk machine: avx_64_mmx_orc
>>>> -- Opening a USRP2/N-Series device...
>>>> -- Current recv frame size: 1472 bytes
>>>> -- Current send frame size: 1472 bytes
>>>>
>>>> No gain specified.
>>>> Setting gain to 15.750000 (from [0.000000, 31.500000])
>>>>
>>>> ..............................................................................................SS.SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS.SSSS..S......SS.S......SS.....S....S...S.S.......S....S........^C
>>>>
>>>> I am using ./benchmark_tx.py located
>>>> in gnuradio/gr-digital/examples/narrowband
>>>>
>>>>
>>>>
>>>> On Wed, Jul 17, 2019 at 4:25 PM Nate Temple <nate.tem...@ettus.com>
>>>> wrote:
>>>>
>>>>> Hi Sumit,
>>>>>
>>>>> A couple things to address:
>>>>>
>>>>> 1) Enable Thread priority scheduling on your host
>>>>>
>>>>> Note it is throwing a warning in the output: "[WARNING] [UHD] Unable
>>>>> to set the thread priority. Performance may be negatively affected."
>>>>>
>>>>>
>>>>> https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux#Thread_priority_scheduling
>>>>>
>>>>>
>>>>> 2) Adjust your network buffers
>>>>>
>>>>> "
>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>> Target sock buff size: 2500000 bytes.
>>>>> Actual sock buff size: 1048576 bytes.
>>>>> See the transport application notes on buffer resizing.
>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>> Target sock buff size: 2500000 bytes.
>>>>> Actual sock buff size: 1048576 bytes.
>>>>> See the transport application notes on buffer resizing.
>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>> "
>>>>>
>>>>> https://kb.ettus.com/USRP_Host_Performance_Tuning_Tips_and_Tricks#N2xx
>>>>>
>>>>>
>>>>> What is the command you're using to transmit(which utility and args?)
>>>>>
>>>>>
>>>>> Regards,
>>>>> Nate Temple
>>>>>
>>>>> On Wed, Jul 17, 2019 at 7:06 AM Sumit Kumar via USRP-users <
>>>>> usrp-users@lists.ettus.com> wrote:
>>>>>
>>>>>> Following is what I am getting after the command you asked to run.
>>>>>> The 192.168.10.5 gives SSSSSSS.
>>>>>>
>>>>>> john@john-Precision-M4600:~/pybombs/src/uhd/host/build/utils$
>>>>>> ./usrp_burn_mb_eeprom --read-all --args "addr=192.168.10.5"
>>>>>> Creating USRP device from address: addr=192.168.10.5
>>>>>> [INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>>>>>> UHD_3.15.0.git-1-gf83faf28
>>>>>> [INFO] [USRP2] Opening a USRP2/N-Series device...
>>>>>> [INFO] [USRP2] Current recv frame size: 1472 bytes
>>>>>> [INFO] [USRP2] Current send frame size: 1472 bytes
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UHD] Unable to set the thread priority. Performance may be
>>>>>> negatively affected.
>>>>>> Please see the general application notes in the manual for
>>>>>> instructions.
>>>>>> EnvironmentError: OSError: error in pthread_setschedparam
>>>>>>
>>>>>> Fetching current settings from EEPROM...
>>>>>>     EEPROM ["hardware"] is "2576"
>>>>>>     EEPROM ["revision"] is ""
>>>>>>     EEPROM ["product"] is ""
>>>>>>     EEPROM ["mac-addr"] is "a0:36:fa:26:34:44"
>>>>>>     EEPROM ["ip-addr"] is "192.168.10.5"
>>>>>>     EEPROM ["subnet"] is "255.255.255.255"
>>>>>>     EEPROM ["gateway"] is "255.255.255.255"
>>>>>>     EEPROM ["gpsdo"] is "none"
>>>>>>     EEPROM ["serial"] is "E4R14V4UN"
>>>>>>     EEPROM ["name"] is ""
>>>>>>
>>>>>> Power-cycle the USRP device for the changes to take effect.
>>>>>>
>>>>>> Done
>>>>>>
>>>>>>
>>>>>> john@john-Precision-M4600:~/pybombs/src/uhd/host/build/utils$
>>>>>> ./usrp_burn_mb_eeprom --read-all --args "addr=192.168.10.3"
>>>>>> Creating USRP device from address: addr=192.168.10.3
>>>>>> [INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
>>>>>> UHD_3.15.0.git-1-gf83faf28
>>>>>> [INFO] [USRP2] Opening a USRP2/N-Series device...
>>>>>> [INFO] [USRP2] Current recv frame size: 1472 bytes
>>>>>> [INFO] [USRP2] Current send frame size: 1472 bytes
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UDP] The send buffer could not be resized sufficiently.
>>>>>> Target sock buff size: 2500000 bytes.
>>>>>> Actual sock buff size: 1048576 bytes.
>>>>>> See the transport application notes on buffer resizing.
>>>>>> Please run: sudo sysctl -w net.core.wmem_max=2500000
>>>>>> [WARNING] [UHD] Unable to set the thread priority. Performance may be
>>>>>> negatively affected.
>>>>>> Please see the general application notes in the manual for
>>>>>> instructions.
>>>>>> EnvironmentError: OSError: error in pthread_setschedparam
>>>>>>
>>>>>> Fetching current settings from EEPROM...
>>>>>>     EEPROM ["hardware"] is "2576"
>>>>>>     EEPROM ["revision"] is ""
>>>>>>     EEPROM ["product"] is ""
>>>>>>     EEPROM ["mac-addr"] is "a0:36:fa:26:34:42"
>>>>>>     EEPROM ["ip-addr"] is "192.168.10.3"
>>>>>>     EEPROM ["subnet"] is "255.255.255.255"
>>>>>>     EEPROM ["gateway"] is "255.255.255.255"
>>>>>>     EEPROM ["gpsdo"] is "none"
>>>>>>     EEPROM ["serial"] is "E4R14V2UN"
>>>>>>     EEPROM ["name"] is ""
>>>>>>
>>>>>> Power-cycle the USRP device for the changes to take effect.
>>>>>>
>>>>>> Done
>>>>>>
>>>>>>
>>>>>> On Wed, Jul 17, 2019 at 3:19 PM Jason Matusiak <
>>>>>> ja...@gardettoengineering.com> wrote:
>>>>>>
>>>>>>> You are right, the table of revisions was for the X-series
>>>>>>>
>>>>>>> try running the command from your prefix:
>>>>>>> src/uhd/host/build/utils/usrp_burn_mb_eeprom --args="type=n200" 
>>>>>>> --read-all
>>>>>>>
>>>>>>> don't quote me on the type portion, I don't have a board in front of
>>>>>>> me to see if it is n200 or something else.  I //think// that will report
>>>>>>> the major and minor revision values (I am grasping at straws here, just
>>>>>>> trying to figure out what the differences might be).
>>>>>>>
>>>>>>> You are connecting the ethernet connections to the two devices
>>>>>>> through the exact same port on your PC?
>>>>>>>
>>>>>>> ------------------------------
>>>>>>> *From:* Sumit Kumar <cog...@gmail.com>
>>>>>>> *Sent:* Wednesday, July 17, 2019 8:24 AM
>>>>>>> *To:* Jason Matusiak <ja...@gardettoengineering.com>
>>>>>>> *Cc:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
>>>>>>> *Subject:* Re: [USRP-users] Sequence Errors N200
>>>>>>>
>>>>>>> The sticker  for sbx shows F33612 and F33814.
>>>>>>> How will this help ?
>>>>>>>
>>>>>>>
>>>>>>> On Wed, Jul 17, 2019 at 1:50 PM Jason Matusiak <
>>>>>>> ja...@gardettoengineering.com> wrote:
>>>>>>>
>>>>>>> Sumit,
>>>>>>>
>>>>>>> OK, the last idea I have:
>>>>>>>
>>>>>>> There is a sticker on the back of the N-series devices it *usually* says
>>>>>>> the version there, but not always.  This has a little info:
>>>>>>> https://kb.ettus.com/About_the_Motherboard_and_Daughtercard_EEPROM_on_USRP_Devices#N200.2F210_EEPROM
>>>>>>>
>>>>>>> Do they match?
>>>>>>>
>>>>>>> ------------------------------
>>>>>>> *From:* Sumit Kumar <cog...@gmail.com>
>>>>>>> *Sent:* Wednesday, July 17, 2019 7:45 AM
>>>>>>> *To:* Jason Matusiak <ja...@gardettoengineering.com>
>>>>>>> *Cc:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
>>>>>>> *Subject:* Re: [USRP-users] Sequence Errors N200
>>>>>>>
>>>>>>> Hi Jason,
>>>>>>>
>>>>>>> Yes they are consistent, I mean the output of uhd_usrp_probe for
>>>>>>> both N200 is exactly the same (except the ip, serial and mac addr).
>>>>>>> I do not know where the problem is! Hardware or software
>>>>>>>
>>>>>>> Regards
>>>>>>> Sumit
>>>>>>>
>>>>>>> On Wed, Jul 17, 2019 at 1:19 PM Jason Matusiak <
>>>>>>> ja...@gardettoengineering.com> wrote:
>>>>>>>
>>>>>>> I am not really an N-series guy, so this probably won't be helpful.
>>>>>>> Have you tried doing a uhd_usrp_probe on both devices and seen that the
>>>>>>> responses are consistent?
>>>>>>>
>>>>>>> ------------------------------
>>>>>>> *From:* USRP-users <usrp-users-boun...@lists.ettus.com> on behalf
>>>>>>> of Sumit Kumar via USRP-users <usrp-users@lists.ettus.com>
>>>>>>> *Sent:* Wednesday, July 17, 2019 7:15 AM
>>>>>>> *To:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
>>>>>>> *Subject:* [USRP-users] Sequence Errors N200
>>>>>>>
>>>>>>> Hi,
>>>>>>> I am trying transmit using Ettus N200 (call it A) but getting this
>>>>>>> error message on the console
>>>>>>>
>>>>>>>
>>>>>>> SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSUSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
>>>>>>>
>>>>>>> I looked for it on google and found these links
>>>>>>>
>>>>>>> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2014-May/037495.html
>>>>>>>
>>>>>>> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2012-July/032838.html
>>>>>>>
>>>>>>> Both the links  suggested problem related to the gigabit port. Then
>>>>>>> I connected another USRP N200 (call it B) to the same laptop and tried
>>>>>>> transmitting using that as there were no such sequence error messages.
>>>>>>>
>>>>>>> This makes me believe there is some problem with the first USRP,
>>>>>>> i.e., A.
>>>>>>>
>>>>>>> Further I tried with different versions of UHD 3.11, UHD 3.15.. but
>>>>>>> its the same.
>>>>>>>
>>>>>>> Receive is good only transmit is throwing error.
>>>>>>>
>>>>>>> Not only with UHD, even in labview, when I transmit, I see nothing
>>>>>>> coming out from the N200 (A).
>>>>>>>
>>>>>>> I am using SBXv2 daughter board.
>>>>>>>
>>>>>>> Any clue!
>>>>>>>
>>>>>>> Regards
>>>>>>> --
>>>>>>> --
>>>>>>> Sumit kumar
>>>>>>> Postdoc
>>>>>>> SnT, Luxembourg
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> --
>>>>>>> Sumit kumar
>>>>>>> Postdoc
>>>>>>> SnT, Luxembourg
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> --
>>>>>>> Sumit kumar
>>>>>>> Postdoc
>>>>>>> SnT, Luxembourg
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>
>>>>>> --
>>>>>> --
>>>>>> Sumit kumar
>>>>>> Postdoc
>>>>>> SnT, Luxembourg
>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>> USRP-users mailing list
>>>>>> USRP-users@lists.ettus.com
>>>>>> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
>>>>>>
>>>>>
>>>>
>>>> --
>>>> --
>>>> Sumit kumar
>>>> Postdoc
>>>> SnT, Luxembourg
>>>>
>>>>
>>>>
>>
>> --
>> --
>> Sumit kumar
>> Postdoc
>> SnT, Luxembourg
>>
>>
>>

-- 
-- 
Sumit kumar
Postdoc
SnT, Luxembourg
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com

Reply via email to