You are right, the table of revisions was for the X-series try running the command from your prefix: src/uhd/host/build/utils/usrp_burn_mb_eeprom --args="type=n200" --read-all
don't quote me on the type portion, I don't have a board in front of me to see if it is n200 or something else. I //think// that will report the major and minor revision values (I am grasping at straws here, just trying to figure out what the differences might be). You are connecting the ethernet connections to the two devices through the exact same port on your PC? ________________________________ From: Sumit Kumar <cog...@gmail.com> Sent: Wednesday, July 17, 2019 8:24 AM To: Jason Matusiak <ja...@gardettoengineering.com> Cc: usrp-users@lists.ettus.com <usrp-users@lists.ettus.com> Subject: Re: [USRP-users] Sequence Errors N200 The sticker for sbx shows F33612 and F33814. How will this help ? On Wed, Jul 17, 2019 at 1:50 PM Jason Matusiak <ja...@gardettoengineering.com<mailto:ja...@gardettoengineering.com>> wrote: Sumit, OK, the last idea I have: There is a sticker on the back of the N-series devices it usually says the version there, but not always. This has a little info: https://kb.ettus.com/About_the_Motherboard_and_Daughtercard_EEPROM_on_USRP_Devices#N200.2F210_EEPROM Do they match? ________________________________ From: Sumit Kumar <cog...@gmail.com<mailto:cog...@gmail.com>> Sent: Wednesday, July 17, 2019 7:45 AM To: Jason Matusiak <ja...@gardettoengineering.com<mailto:ja...@gardettoengineering.com>> Cc: usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com> <usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com>> Subject: Re: [USRP-users] Sequence Errors N200 Hi Jason, Yes they are consistent, I mean the output of uhd_usrp_probe for both N200 is exactly the same (except the ip, serial and mac addr). I do not know where the problem is! Hardware or software Regards Sumit On Wed, Jul 17, 2019 at 1:19 PM Jason Matusiak <ja...@gardettoengineering.com<mailto:ja...@gardettoengineering.com>> wrote: I am not really an N-series guy, so this probably won't be helpful. Have you tried doing a uhd_usrp_probe on both devices and seen that the responses are consistent? ________________________________ From: USRP-users <usrp-users-boun...@lists.ettus.com<mailto:usrp-users-boun...@lists.ettus.com>> on behalf of Sumit Kumar via USRP-users <usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com>> Sent: Wednesday, July 17, 2019 7:15 AM To: usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com> <usrp-users@lists.ettus.com<mailto:usrp-users@lists.ettus.com>> Subject: [USRP-users] Sequence Errors N200 Hi, I am trying transmit using Ettus N200 (call it A) but getting this error message on the console SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSUSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................... I looked for it on google and found these links http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2014-May/037495.html http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2012-July/032838.html Both the links suggested problem related to the gigabit port. Then I connected another USRP N200 (call it B) to the same laptop and tried transmitting using that as there were no such sequence error messages. This makes me believe there is some problem with the first USRP, i.e., A. Further I tried with different versions of UHD 3.11, UHD 3.15.. but its the same. Receive is good only transmit is throwing error. Not only with UHD, even in labview, when I transmit, I see nothing coming out from the N200 (A). I am using SBXv2 daughter board. Any clue! Regards -- -- Sumit kumar Postdoc SnT, Luxembourg -- -- Sumit kumar Postdoc SnT, Luxembourg -- -- Sumit kumar Postdoc SnT, Luxembourg
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
