Following is what I am getting after the command you asked to run. The
192.168.10.5 gives SSSSSSS.

john@john-Precision-M4600:~/pybombs/src/uhd/host/build/utils$
./usrp_burn_mb_eeprom --read-all --args "addr=192.168.10.5"
Creating USRP device from address: addr=192.168.10.5
[INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
UHD_3.15.0.git-1-gf83faf28
[INFO] [USRP2] Opening a USRP2/N-Series device...
[INFO] [USRP2] Current recv frame size: 1472 bytes
[INFO] [USRP2] Current send frame size: 1472 bytes
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UHD] Unable to set the thread priority. Performance may be
negatively affected.
Please see the general application notes in the manual for instructions.
EnvironmentError: OSError: error in pthread_setschedparam

Fetching current settings from EEPROM...
    EEPROM ["hardware"] is "2576"
    EEPROM ["revision"] is ""
    EEPROM ["product"] is ""
    EEPROM ["mac-addr"] is "a0:36:fa:26:34:44"
    EEPROM ["ip-addr"] is "192.168.10.5"
    EEPROM ["subnet"] is "255.255.255.255"
    EEPROM ["gateway"] is "255.255.255.255"
    EEPROM ["gpsdo"] is "none"
    EEPROM ["serial"] is "E4R14V4UN"
    EEPROM ["name"] is ""

Power-cycle the USRP device for the changes to take effect.

Done


john@john-Precision-M4600:~/pybombs/src/uhd/host/build/utils$
./usrp_burn_mb_eeprom --read-all --args "addr=192.168.10.3"
Creating USRP device from address: addr=192.168.10.3
[INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; Boost_105800;
UHD_3.15.0.git-1-gf83faf28
[INFO] [USRP2] Opening a USRP2/N-Series device...
[INFO] [USRP2] Current recv frame size: 1472 bytes
[INFO] [USRP2] Current send frame size: 1472 bytes
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UDP] The send buffer could not be resized sufficiently.
Target sock buff size: 2500000 bytes.
Actual sock buff size: 1048576 bytes.
See the transport application notes on buffer resizing.
Please run: sudo sysctl -w net.core.wmem_max=2500000
[WARNING] [UHD] Unable to set the thread priority. Performance may be
negatively affected.
Please see the general application notes in the manual for instructions.
EnvironmentError: OSError: error in pthread_setschedparam

Fetching current settings from EEPROM...
    EEPROM ["hardware"] is "2576"
    EEPROM ["revision"] is ""
    EEPROM ["product"] is ""
    EEPROM ["mac-addr"] is "a0:36:fa:26:34:42"
    EEPROM ["ip-addr"] is "192.168.10.3"
    EEPROM ["subnet"] is "255.255.255.255"
    EEPROM ["gateway"] is "255.255.255.255"
    EEPROM ["gpsdo"] is "none"
    EEPROM ["serial"] is "E4R14V2UN"
    EEPROM ["name"] is ""

Power-cycle the USRP device for the changes to take effect.

Done


On Wed, Jul 17, 2019 at 3:19 PM Jason Matusiak <
ja...@gardettoengineering.com> wrote:

> You are right, the table of revisions was for the X-series
>
> try running the command from your prefix:
> src/uhd/host/build/utils/usrp_burn_mb_eeprom --args="type=n200" --read-all
>
> don't quote me on the type portion, I don't have a board in front of me to
> see if it is n200 or something else.  I //think// that will report the
> major and minor revision values (I am grasping at straws here, just trying
> to figure out what the differences might be).
>
> You are connecting the ethernet connections to the two devices through the
> exact same port on your PC?
>
> ------------------------------
> *From:* Sumit Kumar <cog...@gmail.com>
> *Sent:* Wednesday, July 17, 2019 8:24 AM
> *To:* Jason Matusiak <ja...@gardettoengineering.com>
> *Cc:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
> *Subject:* Re: [USRP-users] Sequence Errors N200
>
> The sticker  for sbx shows F33612 and F33814.
> How will this help ?
>
>
> On Wed, Jul 17, 2019 at 1:50 PM Jason Matusiak <
> ja...@gardettoengineering.com> wrote:
>
> Sumit,
>
> OK, the last idea I have:
>
> There is a sticker on the back of the N-series devices it *usually* says
> the version there, but not always.  This has a little info:
> https://kb.ettus.com/About_the_Motherboard_and_Daughtercard_EEPROM_on_USRP_Devices#N200.2F210_EEPROM
>
> Do they match?
>
> ------------------------------
> *From:* Sumit Kumar <cog...@gmail.com>
> *Sent:* Wednesday, July 17, 2019 7:45 AM
> *To:* Jason Matusiak <ja...@gardettoengineering.com>
> *Cc:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
> *Subject:* Re: [USRP-users] Sequence Errors N200
>
> Hi Jason,
>
> Yes they are consistent, I mean the output of uhd_usrp_probe for both N200
> is exactly the same (except the ip, serial and mac addr).
> I do not know where the problem is! Hardware or software
>
> Regards
> Sumit
>
> On Wed, Jul 17, 2019 at 1:19 PM Jason Matusiak <
> ja...@gardettoengineering.com> wrote:
>
> I am not really an N-series guy, so this probably won't be helpful.  Have
> you tried doing a uhd_usrp_probe on both devices and seen that the
> responses are consistent?
>
> ------------------------------
> *From:* USRP-users <usrp-users-boun...@lists.ettus.com> on behalf of
> Sumit Kumar via USRP-users <usrp-users@lists.ettus.com>
> *Sent:* Wednesday, July 17, 2019 7:15 AM
> *To:* usrp-users@lists.ettus.com <usrp-users@lists.ettus.com>
> *Subject:* [USRP-users] Sequence Errors N200
>
> Hi,
> I am trying transmit using Ettus N200 (call it A) but getting this error
> message on the console
>
>
> SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSUSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
>
> I looked for it on google and found these links
>
> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2014-May/037495.html
>
> http://lists.ettus.com/pipermail/usrp-users_lists.ettus.com/2012-July/032838.html
>
> Both the links  suggested problem related to the gigabit port. Then I
> connected another USRP N200 (call it B) to the same laptop and tried
> transmitting using that as there were no such sequence error messages.
>
> This makes me believe there is some problem with the first USRP, i.e., A.
>
> Further I tried with different versions of UHD 3.11, UHD 3.15.. but its
> the same.
>
> Receive is good only transmit is throwing error.
>
> Not only with UHD, even in labview, when I transmit, I see nothing coming
> out from the N200 (A).
>
> I am using SBXv2 daughter board.
>
> Any clue!
>
> Regards
> --
> --
> Sumit kumar
> Postdoc
> SnT, Luxembourg
>
>
>
>
> --
> --
> Sumit kumar
> Postdoc
> SnT, Luxembourg
>
>
>
>
> --
> --
> Sumit kumar
> Postdoc
> SnT, Luxembourg
>
>
>

-- 
-- 
Sumit kumar
Postdoc
SnT, Luxembourg
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com

Reply via email to