Re: Stus-List C&C 37+ Mast Head Light

Ha ha, been there! No genius here! Sent from my iPad > On Aug 9, 2020, at 17:07, Rob Hamlin via CnC-List > wrote: > > Hi > To avoid two trips up the stick, know of a replacement LED bulb in kind for > the mast head light? > > Thanks > Rob > > > Sent from my iPhone > ___

Re: Stus-List Sen-Dure heat exchanger

I am seeing a drawing on www.heatexchandeshop.com There is also a website. Www.sen-Dure.com. Hope it helps. Sent from my iPad > On Jul 30, 2020, at 06:06, Tortuga via CnC-List wrote: > >  > Hi. Is there anyone out there who has a diagram, instructions, or other > information about a Sen-Dure

Re: Stus-List Fuel Lift Pump

I changed mine out. I don’t recall losing any oil. Rick Paikea. 37+. Bremerton, WA Sent from my iPad > On Jul 21, 2020, at 16:04, Tom Buscaglia via CnC-List > wrote: > > So, if I understand recent responses to my recent post on running out of > fuel at less than an empty tank, the theory i

Re: Stus-List Overheating Yanmar 3GMD

Just a suggestion, if it happens again, pull the hose off of the through hull supplying raw water to your Yanmar. Open the valve and you should get a face full of SF Bay. If not, you may have sucked something into the raw water feed that did not hit the filter. In my case I found a very surpri

Re: Stus-List icebox drain

Matt > > From: CnC-List On Behalf Of Rick Rohwer via > CnC-List > Sent: Tuesday, June 23, 2020 1:14 PM > To: cnc-list@cnc-list.com > Cc: Rick Rohwer > Subject: Re: Stus-List icebox drain > > The galley foot pump in my 37+ is configured to pump the ice box into t

Re: Stus-List icebox drain

The galley foot pump in my 37+ is configured to pump the ice box into the sink, or by switching two valves, use raw water for dish rinsing etc to save fresh water. Took me a while to figure it out but it’s ingenious! Sent from my iPad > On Jun 23, 2020, at 09:36, Matt Wolford via CnC-List > w

Stus-List Thumping at 6.5 knots

I wrote several responses but they all sounded stupid. We do get some vibration in our rig from different engine/driveline speeds but not a clunking. We get a weird sound (Could be a clunking) if the dinghy is swinging in the davits. I have forgotten to pull the bumpers up resulting in a t

Re: Stus-List Solar Panel Charging Problem

My panels were pretty filthy this spring and I was impressed with the improvement when well scrubbed. Rick Paikea Sent from my > > Thanks everyone for supporting this list with your contributions. Each and > every one is greatly appreciated. If you want to support the list - use > PayPal t

Stus-List Electric windlass

One of the most despised machines on all four sailboats I have owned is the electric windlass. You literally don’t know when it will and won’t function! Buy a manual winch or go to the gym regularly. Rick Paikea 37+. Puget Sound Sent from my iPad > On Apr 29, 2020, at 17:53, Andrew Burton v

Re: Stus-List circuit breakers

You have to open the panel and the breakers are inside. I thought I needed to change one last year and it looked daunting! Bought one and took boat to technician. Turned out it wasn’t the breaker. He indicated that it very seldom is a failure of the breaker but usual a bad ground connection.

Stus-List NW circulation

Bill, We run a small radiant heater in the bow with a dehumidifier in the stern all winter long. I run the water from the dehumidifier into the bilge. The bilge pump takes care of the excess water (which is fresh water and less smelly) We stay in the water year round! I have owned some other

Stus-List Do oil filter magnets work? - YouTube

https://www.youtube.com/watch?v=JW1RfA5Tn7w Sent from my iPad ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution --

Re: Stus-List Force 10 Stove Parts?

Sure Marine rocks! Is Force 10 gone? I talked with them a few years ago and they requested that I order parts from Sure Marine. At that time Sure ordered regularly but wanted to minimize freight by ordering in truckload quantity. It took longer unless you agreed to shipping and handling.

Stus-List Max prop

We went from 3 blade fixed to 3 blade max prop a couple of years ago. Huge difference sailing as expected and I think it backs and fills better than with the fixed prop. I am considering pitching it slightly heavier on the next haul out this winter based on info on this fantastic forum. Than

Stus-List Mast tuning for crew

I had a wonderful crew member (and beautiful woman) who totally unbalanced my (then) Cal 20! l really hated to see her go. Haunts me to this day! I guess I should have had a bigger C&C. Rick Paikea 37+ BREMERTON, WA Rick Rohwer 509 306 1094 > On Aug 20, 2019, at 10:18, Rob Ball via CnC-List

Stus-List I used to do this and got lazy some years ago!

Good info thx Rick Rohwer 509 306 1094 > On Aug 20, 2019, at 12:48, David Knecht via CnC-List > wrote: > > I have been reading about Barber Haulers to help with reaching by getting the > clew further outboard and keeping the leech from twisting off. I was > thinking of a snatch block on

Stus-List more on external effects of wind on mast tune-Coriolis effect | Definition of Coriolis effect at Dictionary.com

https://www.dictionary.com/browse/coriolis-effect Rick Rohwer 509 306 1094 ___ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send c

Stus-List Sardine in intake

David, We sucked an apparently curious sardine headfirst into the intake while visiting Desolation Sound a few years back. Discovered the issue much the same way you did by noticing increased steam in the exhaust. Idled in to an anchorage and starting at the pump worked backward to the intake, whe

Re: Stus-List Diesel engine fire-I chose a Halon ext for my engine

I think Halon is nearly perfect for bilge/mechanical area.on the inert gas sinks like propane, and smothers any fire by denying it oxygen. It also doesn’t hurt the intake system on your most likely, running engine. I learned a lot from a previous rear engine auto engine compartment fire. I proudly

Re: Stus-List Running light bulb access 37+

TOM, you can take it off like I did when the lenz from from the aft white running light jumped out of my hand as I was hanging upside down, and slowly swam into the dark water in Gig Harbor! I think I lost the screwdriver at the same time. That lead to a brand new fixture. Problem solved! Rick Ro

Stus-List thanks for the info

I printed it and will make sure it is on board. Thanks for the information! Rick Paikea 37+ Bremerton, WA > On Apr 19, 2019, at 8:31 AM, Dennis C. via CnC-List > wrote: > > Everything you need, lubrication, cable tension, etc., is here: > > https://edsonmarine.com/content/EB381SteeringGuide.

Re: Stus-List Torque Multiplier to Borrow Locally

Be really careful s you won’t recognize your strength with the multiplier! I have broken some stuff I didn’t think possible! Felt pretty stupid. Rick Paikea 37+ Bremerton, WA Rick Rohwer 509 306 1094 > On Mar 22, 2019, at 13:05, Josh Muckley via CnC-List > wrote: > > You can borrow mine fo

Re: Stus-List Teak interior steps

Hi Bev, we varnished our entryway steps and added some of the abrasive material that was suggested. They are holding up well and not slick. You could pattern the abrasive section on your last coat and make it pretty custom. We did discuss the adhesive backed abrasive products but went for the

Re: Stus-List 37+ Prop Pitch for Universal 35

I have the same prop but a Yanmar 35. Deep keel. Sounds very close to the same performance. I was looking to do the same tweaking on my next haul out. Looking forward to other opinions on the subject. I do love the difference under sail though compared to the fixed prop that was on the boat

Re: Stus-List Merry Christmas and Happy New Year

I spent the night on Paikea last night in Bremerton! Pacific NW A bit nippy, but it felt good to be aboard. Watched Austin Powers-Gold Member and my favorite “Nacho Libre”. No Christmas theme but some good guffaws! Merry Christmas to all! Rick Paikea 37+ > On Dec 23, 2018, at 5:17 PM, svre

Stus-List Youtube of Santa Cruz tsunami 2013

I thought this was an eye opener for anyone with a boat on the West Coast! https://www.youtube.com/watch?v=7O0B9rLaayg ___ Thanks everyone for supporting this list with your contributions. Each and every o

Re: Stus-List Water heater weirdness

Mine behaves similarly. You should be able to bleed the tank from that new valve. I will give it a shot as well. I would guess you have a supply line laying on the hot water hose from the heat exchanger. Rick Rohwer Paikea 37+ Tacoma, WA > On Oct 22, 2018, at 11:21 AM, Jim Watts via

Re: Stus-List Af Cabin Mirror on a 37+

We just replaced ours over the sink mirror, but that doesn’t sound like what you are discussing. Ours was mirrored plastic and we replaced with same from a nearby plastic fab shop. They were also involved in jabbing main hatch and clear hatch board. > On Oct 19, 2018, at 10:22 AM, Bruce Wh

Re: Stus-List C&C 33-2: PYI shaft seal

I agree with Josh, my PYI would be perfect if it could be changed without haul out! I am trying to imagine the circus in the rear stateroom of my 37+ if you tried this change in the water! The failure rate of this PYI system seems to be nearly negligible, the pressure on the mating surfaces i

cnc-list@cnc-list.com

> I love good clean data! Put it in the spreadsheet! > Our first C&C, Paikea was purchased about 5 years ago in Anacortes, WA. We > lived on her a couple years, and then moved indoors. We still love her and shower her with gifts! She rewards us with magical days and nights. She tortures u

Re: Stus-List Chesapeake Bay boat crash

Looks like an Otto Pilot should be responsible! > On Aug 20, 2018, at 6:58 PM, Rick Brass via CnC-List > wrote: > > The fact that the headsail on the J/105 is rolled out implies that he was > sailing, thus he would have had right of way. > > If the J/105 was motor sailing, the power boat was

Re: Stus-List Yanmar 3hmf

I will try to get down to the boat before morning. Sounds like the same rig. > On Jun 19, 2018, at 3:42 PM, pete.shelquist--- via CnC-List > wrote: > > This is a big ask, but my service manuals for the Yanmar 3HMF with Kanzaki > KBW10E transmission are on the boat, which is 4+ hrs away. >

Re: Stus-List Source for LDP Water Tank Inspection Port Caps & O-Rings?

Curious why you would care if the tank leaked at the top of the tank. All of the water is of full use. Fresh water in the bilge. I assume you aren’t taking water in from the fill points, so you are not sinking! I have a similar (possibly the same) problem (and many others) so I wonder why t

Re: Stus-List Enlarging existing hole in glass

Great info guys! Thanks Rick Rohwer Pike 37+ Tacoma, WA > On Jan 19, 2018, at 6:21 AM, Dennis C. via CnC-List > wrote: > > Yeah, forgot to mention that one. That was my first plan. Tried it. It > didn't work for me either. The new 2.75 inch hole saw I bought was a bit > taller than my 2

Re: Stus-List pulling a prawn pot using a boom (not crab pot)

The prawns really fight, all the way to the top swimming hard! Rick Rohwer 509 306 1094 > On Jan 8, 2018, at 08:29, Jeremy Ralph via CnC-List > wrote: > > Ooops. Meant prawn pot :) > > The pots here for Dungeness crabs are at around 50-100ft and easy enough to > pull. Spot prawns are

Re: Stus-List Espar furnace repairs

Nice video, thanks for sharing. Rick 37+ Paikea Tacoma, WA > On Nov 24, 2017, at 8:22 AM, Dan via CnC-List wrote: > > If anyone is interested in how to re-commission an old espar furnace back > into service, I posted a full DIY video on it this week with step by step > instructions. My furn

Re: Stus-List Toilet lubrecation

I like your system. Makes sense to me! Rick Paikea 37+ Tacoma, WA > On Sep 28, 2017, at 3:56 PM, Dennis C. via CnC-List > wrote: > > I've tried tried "head lube", TefGel, wheel grease, couple other things. > Nothing works as well as Superlube. > > So, primarily, I use Superlube. Pop the to

Re: Stus-List How long do your zincs last (saltwater, on a dock, plugged in to shore power

Sounds normal to me in Puget Sound! Rick Paikea 37+ Thea Foss, Tacoma Rick > On Sep 25, 2017, at 3:48 PM, Leslie Paal via CnC-List > wrote: > > that is about the same I get, maybe a little more. > > Leslie > Phoenix > C&C32 1983 > Alamitos Bay Marina. > >

Re: Stus-List Keel bolt torque w/multiplier

I used a multiplier on a transmission bolt and literally twisted it off the truck. The torque it supplies is real, so treat it with respect. > On Sep 23, 2017, at 1:42 PM, ssjohnson via CnC-List > wrote: > > I was seeking a more efficient way to torque the keel bolts and found a > multip

Re: Stus-List CnC-List Digest, Vol 140, Issue 81

Good info Tom! He is now in autodial! Rick Rohwer Paikea 37+ Thea Foss > On Sep 17, 2017, at 13:34, Tom Buscaglia via CnC-List > wrote: > > Don > > I used an excellent diesel mechanic in Sydney this summer. He was > recommended by Stewart, at U.K. Sails and is the best diesel mechanic I

Re: Stus-List GPS, Chart Plodders and Technology when there is none

I have general charts aboard and tools to dead reckon with! I can see no reason to not have at least a handheld GPS aboard with batteries. If you can swing it though you should have a plotter! Great peace of mind! I think I would prefer having AIS to radar. I have the radar but no AIS currently

Re: Stus-List 37+ heat

We have Espar (diesel) and Dickinson (LPG) aboard Paikea. Recent work on the Espar reduced the number of heat vents to 3: aft stateroom, Head and under the chart table. Too many heat vents pressure stressed the blower previously and “coked” the unit. Really works well (blows hard) at this poi

Re: Stus-List Overheating mystery

I sucked a sardine into the raw water intake in Powell River. I idled back to P R worked from the pump backwards, and there he was with a steely gaze halfway up the through hull. If he would have extracted himself first I would still be looking for answers! It does bring up a question that has

Re: Stus-List PVC Handrails, 12" On Center

I read somewhere on the forum that the holes mounting those rails are not a standard distance apart. I would have them reproduce from the original! My wife takes great pride in her varnish on those rails! I am a lucky man! Rick Paikea 37/40 Rick Rohwer 509 306 1094 > On Aug 9, 2017, at 09:0

Re: Stus-List Bow light

I used the old wire to pull the new! It may have been dumb luck though! Sometimes even I get some dumb luck! Rick Paikea 37/40 Friday Harbor until 10:00 today and then off to Orcas. Rick Rohwer 509 306 1094 > On Aug 9, 2017, at 06:24, Joel Aronson via CnC-List > wrote: > > It is a PIA job!

Re: Stus-List Reminder: ONE MONTH AWAY -- C&C 2017 Northeast Rendezvous -- Sept. 8-10, 2017 -- Greenport, Long Island

Hi Edd Just returned from a 2 month trip into Canada on 37+ hull 53 but returning 1 week too early for the C&C rendezvous in Telegraph Harbor on Thetis Island , BC. We will be in the neighborhood of your rendezvous on the 10th with a rental car and would love to check out your party. If we can

Re: Stus-List Westerbeke 33 oil burn

Would a thousand hours in the Suburban be 20 hours? How does that compare to your motoring time to Maine? I sail on the west coast so I don't have a clue how many hours of operation is involved from Newport to Maine. Rick Rohwer 509 306 1094 > On Jun 4, 2017, at 11:39, PETER OCAMPO via CnC-

Re: Stus-List Unique 3 way wire connector

bravo, nice idea! On Thu, May 25, 2017 at 3:05 PM, Dennis C. via CnC-List < cnc-list@cnc-list.com> wrote: > Had a situation where I wanted to connect two wires twisted and soldered > together with two smaller individual wires. The individual wires could use > a 14-16 connector but the twisted wi

Re: Stus-List Eberspacher D1L Heater

Hi Eugene, I had some folks local to Tacoma, WA work on my Espar d3L unit in the spring and they did a great job. Parts are sometimes hard to acquire. There are individual parts of the heaters that are prone to failure that cannot be effectively fixed! and are critical to dependable performance.

Re: Stus-List 37/40+ What does small switch on ceiling do?

I believe I have said switch and it controls two neon lights under the ceiling panels. The panels are held in place with velcro. Rick Paikea 37+ Tacoma, WA On Mon, May 1, 2017 at 7:11 AM, Josh Muckley via CnC-List < cnc-list@cnc-list.com> wrote: > Yep, I almost bought a windex light and then re

Re: Stus-List Diesel Air Heaters (Webasto, Planar, Eberspaecher/Espar)

Hi Joel I was looking at a replacement for my Espar last winter and was able to find someone to rebuild/repair my existing system and "fix" some of the problems inherent in the original installation. Too many ducts were installed for the system and none forward of the rear stateroom received adequ

Re: Stus-List Climbing the mast solo

I use the same ascenders with my own concoction of straps but unlike the fellow in the “atninc" ad I prefer a bosun’s chair to a climbing harness. Plenty of pockets for tools and your vitals don’t go numb. These allow you to actually climb above the top of the mast so you can work readily on mast

Re: Stus-List Automatic Bilge Pump? Recommendations?

Mine is also a Rule (I think the capacity is around 650gpm) with electronic switch, redundant with another of the same in the shallow sump under the steps. They are both automatic or on with switch at nav table. Everything ultimately drains into the deep sump on my boat as well using (just learne

Re: Stus-List Mast Step Box 1980 CnC36

I agree with Dwight, that you will save time, frustration and probably money with the mast off of the boat. It sounds like a big deal, but it is usually a relatively cheap and simple maneuver and provides you a great opportunity to work on the mast, rigging, lighting etc. while out of the boat.

Re: Stus-List Possible Boom modification

I wear a helmet for several different activities that I am involved in. Several other activities that generally use helmets I feel comfortable without it. If I were worried about my head while sailing I think I might consider a helmet. A climbing helmet would serve the purpose very well. Giv

Re: Stus-List freeze proofing

Hi Jeremy, The water (coolant) inside the freshwater cooled engine is controlled by the thermostat. Coolant is approx 50% glycol to reduce the freeze point of the coolant (-25F or more). When the engine hits the set temp (190F), the thermostat opens and allows coolant cooled by the heat exc

Re: Stus-List Cockpit Locker Leak...

This has occurred on my 37+ in the past. The drain on the combing blocks, backs up, and floods into the locker, I check it routinely and use an air pump to blow it clean. The lockers share the same drain line and in one case filled about half full of water before I caught it. Rick Paikea 3

Re: Stus-List Vent Fans -- Where Do You Have Them?

Hi Edd We have been running dehumidifier and some heat (living aboard) most of the winter so we are golden, but last winter was a different story. Not much air movement on the 37+. I had some solar vents on past boats and they were great. i am wondering if you could set up a low voltage fa

Re: Stus-List Vent Fans -- Where Do You Have Them?

Hi Edd We have been running dehumidifier and some heat (living aboard) most of the winter so we are golden, but last winter was a different story. Not much air movement on the 37+. I had some solar vents on past boats and they were great. i am wondering if you could set up a low voltage fa

Re: Stus-List Overheating YANMAR

Hi Tom Sorry to hear about your issue! I was going to suggest a look at the through hull as we had sucked a sardine into ours in desolation sound a while back, but in that case the flow of water was drastically changed. Backing down on the engine to idle allowed for a return to port. I have

Re: Stus-List Horizon Instrument Covers and Bow Anchor Roller for 29 mk II

Hi Gene, A well working bilge pump is always a good thing! I have a leak on the fill for one of my fresh water tanks. It doesn’t limit the amount of water I have on board, just leaks when the water level is above the tank level. I am not in a hurry to find it as my bilge pumps all work fine a

Stus-List C&C Letters for 37+ exterior

I lost the recent message regarding replacement letters water jetted from smoked plastic. I am missing “C” and “&” Can someone forward that info to me again? Much appreciated. Rick Paikea 37+ Poulsbo, WA ___ This list is supported by the generous d

Re: Stus-List Scanmar Emergency Rudder MRUD

I am not sure what you have Adam. That might mean I don’t need it, but it makes me curious that I am missing out on something! Cheers Rick Paikea 37+ Poulsbo, WA > On Apr 27, 2016, at 5:07 PM, Adam Trackracer via CnC-List > wrote: > > Hello, I own a 1973 C&C39 BlackWatch in Seattle and I hav

Re: Stus-List Icebox pump

Mine siphons to the first sump near the engine and goes to the bilge. Ice box water can get a tad nasty. Tastes nasty anyway as I still suck (pun) with no talent! Rick Paikea 37+ Poulsbo, WA > On Apr 27, 2016, at 5:57 PM, Josh Muckley via CnC-List > wrote: > > Mine doesn't work either but s

Stus-List Rudder replacement/repair

Thanks for sharing the pictures Joh! Very interesting. Rick Paikea 37+ Poulsbo, WA > On Apr 18, 2016, at 9:17 PM, Josh Muckley via CnC-List > wrote: > > My rebuild was ~$5k. Seeing what the professionals do was definitely an > education. Not hard, just a lot of work. > > https://drive.goo

Re: Stus-List LED Nav Lights

When under power you are no longer a sailing vessel. White Light showing 225 over port and starboard running lights. Just one more tug boat. Sent from my iPhone > On Apr 4, 2016, at 19:26, Rick Brass via CnC-List > wrote: > > I don’t recall any requirement in the COLREGS that a “Masthead” l

Re: Stus-List Keel bolt tightening for wimps?

Ryan I have had some painful experience with a torque multiplier! Whether tightening or loosening, you should be wary of how much force you are applying to the fastener. Fasteners or sockets can fragment. I would recommend either some pretreatment with penetrating oil, and or heating/cooling.

Re: Stus-List CnC-List Digest, Vol 122, Issue 42

Thanks for the idea. I may go even larger on the inspection hatch. Rick Paikea 37+ > On Mar 16, 2016, at 5:13 PM, Brian Fry via CnC-List > wrote: > > La Neige, a 37/40 XL has an access cover in the head. It is one of those > hinged plastic rectangular shaped hatches. Highly recommend at least

Re: Stus-List Fuel

Al, .75 gph sounds about right to me as well. Some safety built into that number. 3HM35F with 3 blade prop @2200rpm C&C 37+. Rick Paikea Poulsbo, WA > On Feb 16, 2016, at 7:50 PM, Andrew Burton via CnC-List > wrote: > > I would use 3/4 gal/hour as a safe number. My 3gm uses 0.6 to push my

Re: Stus-List Diesel Heaters and installation

Mine pulls 12amps until the glow plug goes off. Rick. Paikea 37+ Sent from my iPhone > On Feb 6, 2016, at 13:17, William Walker via CnC-List > wrote: > > Graham, >Your thoughts would appreciated on start up draw. Prior owner installed > in port Lazarette. He is particular guy, all looks

Re: Stus-List ab inflatables

We have been happy with our 9ft AB-hypalon tender thus far. i felt the aluminum hull would be the least likely to be damaged in beach landing and wouldn’t show the scratching from rocks and debris while tied to the beach. Nearly any shop or amateur welder can fix aluminum, some prettier than o

Re: Stus-List Fwd: Stainless steel name plates (46088)

Ken, Count me in for a set of each side on a group order if that can be established. Let me know when and how to pay for same. Thx Rick Paikea37+ cell: (509)3061094 rickroh...@gmail.com Ship to: PO Box 892,Gig Harbor, WA 98335 > On Jan 12, 2016, at 12:13 PM, Ken Heaton via CnC-List > wrote:

Re: Stus-List C&C 37+ nameplates for sale

i am probably not interested in the SS version but very interested in the other. Thanks > On Jan 11, 2016, at 4:02 PM, Josh Muckley via CnC-List > wrote: > > Interested in a quote for something in a polished chrome or stainless. > > Josh Muckley > > On Jan 11, 2016 6

Re: Stus-List C&C 37+ nameplates for sale

Interested Sent from my iPhone > On Jan 11, 2016, at 14:47, Gary Russell via CnC-List > wrote: > > Well, I've got what I consider a reasonable quote for the nameplates. I can > supply them in black UV resistant polycarbonate for $75 each side plus > shipping.. That includes everything incl

Re: Stus-List winter condensation

Hi Joe We are running a dehumidifier about 10 hrs a day. Really dried things up and is very comfortable. 34F outside, 64F inside and climbing. We have it set to pull it down to 50 and shut off. You can set them up to pump into the bilge or sink if you choose. Got this one at home depot. Che

Re: Stus-List (no subject)

Chuck For my two bits, Sterling Hayden wrote some damn fine books. They lit me up! Rick Paikea 37+ Poulsbo, WA (damn it’s cold) > On Dec 31, 2015, at 12:58 PM, Dave via CnC-List wrote: > > Whynott - a new one for the list- thanks. wanderer is great, re read many > times. Sterling Hayden wa

Re: Stus-List FAO: Owner of Mithrandir II

i’d be willing to kick in for a reward to this fella for making the effort to get the dinghy back to the owner. i’ll buy him a pint in Sidney on the next trip up! Give me his contact info! Cheers back Rick Paikea 37+ > On Dec 29, 2015, at 7:08 PM, Paul Baker via CnC-List > wrote: > > I seem

Re: Stus-List Proper Blower Installation - 30 mki

I am pretty sure vaporized diesel will blow up like gasoline vapor. I know vaporized cooking fat will. Don’t most of the fuel docks ask you to shut down the engine and run the fan while fueling? I had never thought of it as an air supply for the engine. Rick Paikea 37+ Poulsbo, WA > On

Re: Stus-List New beer can Genoa

Jon, You could approach the problem at the root; will you consider getting rid of the wife? ha ha, just kidding but it is tempting for me when my wife is the only obstacle between me and my toys! Merry Christmas Rick Paikea 37+ Currently Bell Harbor, Seattle, WA > On Dec 25, 2015, at 12:08 PM

Re: Stus-List Holiday wishes

We had 33 knots from the south with a nice square 7 foot chop on the nose and a beautiful 33 Degrees F. It was a freezy roller coaster. Merry Christmas all, Rick Paikea 37+ Poulsbo, WA > On Dec 24, 2015, at 5:06 PM, Marek Dziedzic via CnC-List > wrote: > > > This weather IS crazy. It was 1

Re: Stus-List : off topic Skiing

. Have truck, will ski! :) > > Dennis C. > Touche' 35-1 #83 > Mandeville, LA > >> On Mon, Dec 14, 2015 at 7:44 PM, Rick Rohwer via CnC-List >> wrote: >> Enivous about equador, and you living in BC and skiing anywhere but BC. >> >> On another

Re: Stus-List : off topic Skiing

Enivous about equador, and you living in BC and skiing anywhere but BC. On another note, I think I have given up on skiing in Whistler so it’s all yours! I think they have finally hit my personal affordability index with $119 for a tow ticket. Explains why you are skiing in Colorado! Cheers R

Re: Stus-List Pleated Blinds

We had ours dry cleaned and it really helped a lot. They were just dusty I guess. They hadn’t seen the sun much. It really brightened them up. Rick Paikea 37+ Poulsbo, WA > On Dec 9, 2015, at 9:52 AM, Gary Russell via CnC-List > wrote: > > The pleated window blinds / shades in my 37 Plus ha

Re: Stus-List Lewmar Ocean Hatch Seals

i had been in contact with lewmar a couple of years ago trying to procure a trim kit for the 60 Series. I was told that no parts for my hatch were still in the distribution chain and i would need it to change the hatch out to the “new” style hatch. Corner radii are different. i met a fellow

Re: Stus-List outboard size

We have 8' AB aluminum bottom with 5hp Merc 2stroke long shaft. Works great but won't plane with more than one aboard Cheers Rick Paige's 37+ Poulsbo, WA Sent from my iPhone > On Oct 26, 2015, at 10:27 AM, Gary Nylander via CnC-List > wrote: > > The J-80 I race on uses a Honda 2hp 4 stroke.

Re: Stus-List Anti-fouling paint

Wow, 3 years for bottom paint is pretty darn good! Are you in really cold or brackish environment? I have a neighbor in my marina that is going to be in the Smithsonian if he can keep the garden growing under his vintage Columbia sloop! He did get a nice 25 hp Merc installed on the back since I

Re: Stus-List bilge pump

Hi My 37+ has 750gph in a shallow bilge and 1250gph in the deep bilge. I am replacing the backup manual pump from the cockpit that if you have a frightened man aboard is rated at 15 gpm (in that range, the more scared you are the higher the rating)! The mechanism recently failed so a brand new

Re: Stus-List bus heater

I had a similar heater (Red Dot) on a previous 36 ft cutter with vent in salon. It would nearly drive you out of the boat with heat. I hope to install similar heater on my boat using existing ducting from my Espar heater so that either system could provide heat depending on whether the engine wa

Re: Stus-List SOS light flare replacement

Doug, i just bought a couple of handheld strobes from NorthAmericanSurvivalSystems.com . I think they will be very effective insurance for several activities that my wife are involved with including sailing. They weigh 5 oz including two Lithium CR123

Re: Stus-List Autopilot steering

Hi My 37+ pulls hard to port under full throttle, prop effect I am sure. I am running a 3 blade prop. You might be able to minimize the effect with a prop change. Good luck. Rick > On Aug 26, 2015, at 10:43 AM, David Knecht via CnC-List > wrote: > > Calling Raymarine was my first action a

Re: Stus-List Was Wire Gauge, now Where can I get LED?

Hi Jonathan I made a similar change to a perko from Aquasignal 40 series fixture and replaced the bulb with LED.. Very simple. Look carefully at the entry of the wiring so that you don’t have a bottom entry if you have a different type. You need to make sure you have enough wire to connect the n

Re: Stus-List LPG tank -- 37+

my LPG tank is 18” and you might squeeze another .25” but not a .5” Rick Paikea 37+ > On Aug 20, 2015, at 12:01 PM, Tom Buscaglia via CnC-List > mailto:cnc-list@cnc-list.com>> wrote: > > Edd > > I just got back from 3 weeks out. But I eft my glasses on board. So, I'll > be on board later tod

Re: Stus-List Was Wire Gauge, now Where can I get LED?

I have the bulbs and replacement lenz ready to change but can’t find a monkey for the mast work. Several pole climbing ladies have offered and then backed out. I’ll get up there eventually. Rick Paikea 37+ > On Aug 20, 2015, at 9:44 AM, svpegasu...@gmail.com via CnC-List > wrote: > > Alex

Re: Stus-List Battery question for LF38 owners

The fresh water kills all the saltwater organisms, but you are right,the boat should float slightly lower since fresh is lighter than salt!! I’ve had boats in fresh water though and the slime grows just about as fast until you take a sail in the salt. Rick Paikea 37+ > On Aug 19, 2015, at 8

Re: Stus-List LPG tank -- 37+

Hi Edd It is Liquid propane gas, same as barbie! Rick Paikea 37+ > On Aug 20, 2015, at 5:09 AM, Edd Schillay via CnC-List > wrote: > > Listers, > > I think this was covered in the past, but I'm getting older and I forgot the > answer. > > In my 37+, I have a tank labelled LPG for my stove

Re: Stus-List 37 icebox rebuild

Hi I want to replace the seal on my ice box. “Paikea” is a 37+. Anyone know where to source that seal material? Thanks Rick Blake Island (today) > On Aug 19, 2015, at 9:17 AM, Pete Shelquist via CnC-List > wrote: > > Dave – > . I also have a 37 (’84) and just did a quick review of your

Re: Stus-List Rust stains and welding

Citric acid @ 20% Sent from my iPhone > On Aug 17, 2015, at 1:11 PM, Jim Watts via CnC-List > wrote: > > The heat of welding will change the physical properties of stainless, so he > may (probably did) use stainless rod but it's now less stainless. You could > try repassivating it with a pro

Re: Stus-List List down?

No wifi until today in Ladysmith BC. Hope all are well! > On Jul 19, 2015, at 10:41 AM, Frederick G Street via CnC-List > wrote: > > I think everyone (but you and I…) are out on their boats… :^( > > Fred Street -- Minneapolis > S/V Oceanis (1979 C&C Landfall 38) -- Bayfield, WI > >> On Jul

Re: Stus-List C&C 37+ Repower -- Ugh

Thanks Tom. I might be able to get the 7-7.3 but my rpm’s are-2400. I think my tach is off (she could be dirty too) and that is why I have the question. What’s your overall opinion on the MAXPROP? Any suggestion on something else, or is that the prop? Raining in the San Juans this AM but ge

Re: Stus-List Handrail question

Neil Let me know if I can help. I am looking at my 6 loop teak handrails on a 1989-90 37+. Rick Paikea, Langley, Whidbey Island, WA (just for tonight) > On Jul 7, 2015, at 4:24 PM, Neil Andersen via CnC-List > wrote: > > A rigger that I am no longer using broke one of my 6 loop teak handrail

  1   2   >