Hi,
Orange Pi R1 has 2 interfaces, a dwxe(4) and an ure(4).
dwxe(4) is in the SoC but ure(4) is connected through ehci(4). I can reproduce
reliably by simply removing the media and inserting it again. It's stable if
you don't change your topology too much, but crashes often even when not
removing
On Mon, Nov 28, 2022 at 06:11:30PM +0100, Bodie wrote:
> Hi,
>
> trying to install armv7 snapshot from 27.11.2022 on Orange Pi One.
> Once it gets to first part of installer where it asks if I want to
> Install, Upgrade
>
> It starts flooding serial console with messages below and is not
> po
Hi,
I have an Orange Pi R1 (2 network interfaces) for ~3 years as my main router.
At the time, recompiled sysutils/u-boot adding orangepi_r1_defconfig, because
this port doesn't compile for the Orange Pi R1. dd'ed the new compiled u-boot
(same procedure as Cubieboard), replaced the dtb in the mi
On Wed, Jun 03, 2020 at 11:26:16AM -0700, Lear Zhou wrote:
> Testing has been done based on Patrick’s work. It turned out
> that the ure0 is not ready for serious usage.
>
> The issue is that ure0 will hang/freeze there after hours
> usage, while the kernel still running and can be accessed
> via
On Tue, May 19, 2020 at 04:43:54PM +0200, Per Gunnarsson wrote:
> Hello!
>
> I saw the section "PF - Building a router" on your web page and thought
> that would be an interesting hobby project. Now I wonder if it's
> possible to install OpenBSD on a Banana Pi R2. In case it's not possible
> (or s
Hi,
with -current RAMDISK on a Wandboard imx, an external USB disk is attached as
sd1 and there no problems found completing the installation on it. However,
when booting GENERIC, can't see this same external USB disk, and since sd1 is
not found, panic.
The disk is seen by the bootarm EFI load be
On Fri, Feb 16, 2018 at 06:46:57PM +, Heinrich Rebehn wrote:
> On a side note: Is it possible to disable the reordering of the
> libraries on every boot? I takes quite long on the Raspi running from
> USB stick.
# rcctl disable library_aslr
--
db
On Thu, Mar 02, 2017 at 02:24:57PM +1100, Jonathan Gray wrote:
>
> I don't have any allwinner systems here but perhaps a newer u-boot would
> help?
Yes. Thank you.
--
U-Boot SPL 2017.03-rc3 (Mar 02 2017 - 14:13:26)
DRAM: 1024 MiB
CPU: 91200Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U
Hi,
Trying the latest snapshot on Banana Pi and Orange Pi One stopped
before running the EFI workload.
I suspect it's something obvious when modifying the image, but this used
to work to boot the boards without miniroot just fine.
http://marc.info/?l=openbsd-arm&m=148288574314135&w=2
I'd apprec
On Sat, Dec 24, 2016 at 12:26:34AM +0100, Mark Kettenis wrote:
> > Date: Fri, 23 Dec 2016 21:01:38 -0200
> > From: Daniel Bolgheroni
> >
> > On Thu, Dec 22, 2016 at 12:11:36PM -0200, Luiz Gustavo dos S. Costa wrote:
> > > Yesterday, received a new board
On Thu, Dec 22, 2016 at 12:11:36PM -0200, Luiz Gustavo dos S. Costa wrote:
> Yesterday, received a new board to a lab with Linux for a product,
> but, my principal intencion is use with OpenBSD.
I booted on an Orange Pi One this week, with the Allwinner H3 SoC (the
same as in C.H.I.P. board). It w
On Wed, Aug 31, 2016 at 05:36:24PM +0300, alexandr_...@ukr.net wrote:
>
> Hi all.
>
> I have SoC pcduino with specification: CPU 1GHz ARM Cortex A8 GPU OpenGL
> ES2.0, OpenVG 1.1 Mali 400 core DRAM 1GB Onboard Storage 2GB Flash, microSD
> card (TF) slot for up to 32GB Video Output HDMI Ex
On Thu, Aug 04, 2016 at 04:32:09PM +0200, Patrick Wildt wrote:
> Mark just committed a diff that should fix this issue. :-)
I was going to report this after making sure it's not something related
to the network the board is attached.
Before r1.12 and r1.13, as the last commits refers to it, there
On Mon, Jul 25, 2016 at 04:26:26PM +0200, Mark Kettenis wrote:
>
> Also, are you plugged into a gigabit switch? If not, "ifconfig fec0
> media 100baseTX" might help.
Missed that.
Thank you.
--
db
On Mon, Jul 25, 2016 at 04:26:26PM +0200, Mark Kettenis wrote:
>
> Can you show us the output of "ifconfig fec0" and "vmstat -zi"?
Sure. At the bottom of the message.
> Also, are you plugged into a gigabit switch? If not, "ifconfig fec0
> media 100baseTX" might help.
No, cheap Fast Ethernet sw
On Thu, Jul 21, 2016 at 01:06:50PM +1000, Jonathan Gray wrote:
>
> Actually the pad configuration in those commits may mean this isn't
> enough.
Hi,
I saw the r1.9 for if_fec.c and then it says it was tested on SABRE lite by
Patrick.
I tested on Wandboard Solo again. Now fec(4) shows up, howeve
On Wed, Jul 13, 2016 at 11:39:54AM +0200, Mark Kettenis wrote:
> The diff below removes the last board ID dependent code for the i.MX6
> platform. It affects all boards that use a Micrel PHY, which would
> show up as "ukphy0" in your dmesg. If you have such a board (udoo,
> novena and sabrelight,
On Wed, Jun 29, 2016 at 04:21:39AM +, Karl Hammerschmidt wrote:
> Is anyone else interested in their boards?
For those who are always looking for SBCs to build routers, Banana Pi R1
is cheap and easily available:
http://www.banana-pi.org/r1.html
However, it is also based on Allwinner A20. As
On Mon, May 30, 2016 at 12:02:32AM +1000, Jonathan Gray wrote:
> There is now a bootloader for armv7 thanks to kettenis@
> Recent armv7 snapshots will configure disks to use efiboot and install
> device tree dtb files on a fat partition at the start of the disk.
>
> u-boot kernel images are no lon
Hi,
I've been following armv7 recent changes and these days I was able to
compare kernel compile times on 2 of the supported boards.
The first is an omap BeagleBone Black with a NFS-mounted /usr/src. It's
pretty stable and I had no issues so far with what is supported.
The second is a sunxi Cubi
On Fri, Dec 18, 2015 at 01:27:59PM +0100, Patrick Wildt wrote:
> There had been some external effort to rewrite the PMAP based on
> the PowerPC one. It actually runs on a platform, but it's not stable
> enough. I wish there was more time to work on that.
What are the advantages of the PowerPC-base
On Tue, Oct 20, 2015 at 10:35:39AM +0200, Petr Ročkai wrote:
> welcome to the club. I think that there's an issue affecting all A20's,
> regardless of the board around them. Comparing to an A10 could be
> useful, but those appear to be hard to get by. I'm planning to try an
> am335x (on a beaglebon
On Mon, Oct 19, 2015 at 10:02:44PM +0200, Alexander Kratzsch wrote:
> Does anyone have some idea I could try?
This is hardly an one-answer question. You are asking a very broad
question on how to debug kernels.
Someone might say that you can fill the source code with some printf's
here and there
On Sat, Oct 03, 2015 at 11:54:51AM +0200, Leonardo Guardati wrote:
> Hi,
> I'm back trying to make the pcDuino3_Nano board
> work with OpenBSD.
Just to report, no solutions yet. I have a Cubieboard 2 and a Banana Pi,
both with the A20 SoC like pcDuino3.
With an unmodified RAMDISK, Cubieboard 2
On Thu, Aug 13, 2015 at 07:48:30PM +1000, Jonathan Gray wrote:
> I would be curious to see what happens when running a recent u-boot
> and the following:
>
> Index: armv7_machdep.c
> ===
> RCS file: /cvs/src/sys/arch/armv7/armv7/armv7
On Fri, Aug 07, 2015 at 03:13:58PM +0200, Viktor Pocedulić wrote:
>
> Maybe it is worth mentioning that I can successfully boot various
> Linux distributions so this rules out hardware malfunction.
Although OpenBSD does not support Banana Pi, I had a similar issue
trying to boot OpenBSD on it with
On Fri, Jul 24, 2015 at 10:29:34AM +1000, Jonathan Gray wrote:
> You could try
>
> setenv bootargs "sd0:/bsd.SUNXI.umg -c"
>
> boot and then do
>
> disable sxie*
> quit
>
> at the ukc prompt.
I compiled 2 different U-Boot versions. One is 2014.04 (or somewhat
close to it), using LeMaker git re
On Thu, Jul 23, 2015 at 09:13:08PM -0300, Daniel Bolgheroni wrote:
>
> Not yet. Somehow, this is related to U-Boot 2015.04, since I could boot with
> 2014.04 (not -mainline). Didn't try yet with 2015.07 to see if things changed
> yet.
Forgot to note: booted from fat fs inside
On Thu, Jul 23, 2015 at 05:54:50PM +1000, Jonathan Gray wrote:
> At the u-boot prompt try:
>
> printenv machid
> setenv machid 10bb
Not yet. Somehow, this is related to U-Boot 2015.04, since I could boot with
2014.04 (not -mainline). Didn't try yet with 2015.07 to see if things change
On Wed, Jul 22, 2015 at 04:52:48AM +, Brandon Mercer wrote:
>
> Just to confirm. Are trying to boot the bsd.rd.SUNXI.umg or the
> bsd.SUNXI.umg?
I tried both.
Thank you.
Hi arm@,
Later last year I bought a Banana Pi board and, at that time, was able to boot
OpenBSD on it. I can't really remember where it stopped, since it's not
supported, but at least it booted.
I tried to do the same thing this week, however without success. Here is the
steps I took (to simplify
Hi,
I'm trying to install OpenBSD on a Banana Pi board. So I dd'it the
miniroot-sunxi-56.fs to the SD card and powered the board. This is all I
get:
---
$ sudo cu -115200 /dev/cuaU0
Connected to /dev/cuaU0 (speed 115200)
U-Boot SPL 2012.10-04277-g7aa9f04-dirty (Mar 28 2013 - 22:17:17)
DRAM:
32 matches
Mail list logo
