On Thu, Aug 04, 2016 at 04:32:09PM +0200, Patrick Wildt wrote:
> Mark just committed a diff that should fix this issue. :-)
I was going to report this after making sure it's not something related
to the network the board is attached.
Before r1.12 and r1.13, as the last commits refers to it, there were some
issues related to auto negotiation. It was pointed out to manually set media to
100baseTX, since the board was hooked in a Fast Ethernet switch. OK, so I had
this at hostname.fec0:
inet 192.168.1.3 255.255.255.0
media 100baseTX
mediaopt full-duplex
However, I noticed that after rebooting, the interface aparently was going up
but I couldn't ping it. Only after issuing a "ifconfig fec0" that the interface
was becoming functional.
After the last update, now with r1.12 and r1.13, the same hostname.fec0, there
is no network at all. Without the media/mediaopt the result is the same.
Thank you.
--
$ vmstat -zi
interrupt total rate
irq1023/spur 144 0
irq58/imxuart0 170 0
irq75/imxehci0 0 0
irq72/imxehci1 0 0
irq54/imxesdhc0 40 0
irq55/imxesdhc1 4 0
irq56/imxesdhc2 21427 11
irq60/imxuart1 0 0
irq29/tick 389215 199
Total 411000 211
$
OpenBSD 6.0-current (GENERIC) #0: Thu Aug 4 15:46:32 BRT 2016
dbolgher...@wbs.my.domain:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 536870912 (512MB)
avail mem = 518017024 (494MB)
mainbus0 at root: Wandboard i.MX6 Dual Lite Board rev B1
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 8 waymask: 0x0000000f
imx0 at mainbus0
imxccm0 at imx0: imx6 rev 1.1 CPU freq: 792 MHz
imxiomuxc0 at imx0
imxocotp0 at imx0
simplebus0 at mainbus0: "soc"
ampintc0 at simplebus0 nirq 160
simplebus1 at simplebus0: "aips-bus"
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
simplebus3 at simplebus1: "anatop"
imxgpc0 at simplebus1
simplebus4 at simplebus0: "aips-bus"
imxehci0 at simplebus4
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
imxehci1 at simplebus4
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
fec0 at simplebus4
fec0: address 00:1f:7b:b0:08:52
atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
imxesdhc0 at simplebus4
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus4
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxesdhc2 at simplebus4
imxesdhc2: 198 MHz base clock
sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
imxiic0 at simplebus4
iic0 at imxiic0
imxiic1 at simplebus4
iic1 at imxiic1
"fsl,sgtl5000" at iic1 addr 0xa not configured
imxuart1 at simplebus4
simplebus5 at mainbus0: "regulators"
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed
sd0: 1910MB, 512 bytes/sector, 3911680 sectors
scsibus1 at sdmmc2: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU08G, 0080> SCSI2 0/direct fixed
sd1: 7580MB, 512 bytes/sector, 15523840 sectors
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd1a (8202d1873078fd2f.a) swap on sd1b dump on sd1b
WARNING: CHECK AND RESET THE DATE!
--
db
