On Mon, Jul 25, 2016 at 04:26:26PM +0200, Mark Kettenis wrote: > > Can you show us the output of "ifconfig fec0" and "vmstat -zi"?
Sure. At the bottom of the message. > Also, are you plugged into a gigabit switch? If not, "ifconfig fec0 > media 100baseTX" might help. No, cheap Fast Ethernet switch. http://www.tp-link.com/en/products/details/TL-SF1008D.html Thank you. -- U-Boot SPL 2016.07 (Jul 20 2016 - 21:09:03) Trying to boot from MMC1 U-Boot 2016.07 (Jul 20 2016 - 21:09:03 -0600) CPU: Freescale i.MX6SOLO rev1.1 at 792 MHz Reset cause: WDOG Board: Wandboard rev B1 I2C: ready DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... reading /imx6dl-wandboard-revb1.dtb 29934 bytes read in 20 ms (1.4 MiB/s) Found EFI removable media binary efi/boot/bootarm.efi reading efi/boot/bootarm.efi 65276 bytes read in 33 ms (1.9 MiB/s) ## Starting EFI application at 0x12000000 ... Scanning disks on usb... Scanning disks on mmc... MMC Device 2 not found MMC Device 3 not found Found 6 disks >> OpenBSD/armv7 BOOTARM 0.1 boot> booting sd0a:/bsd: 3722056+101212+479648 [64+496480+232320]=0x4cfd90 OpenBSD/armv7 booting ... arg0 0x0 arg1 0x2e55b26c arg2 0x18000000 Allocating page tables freestart = 0x107d0000, free_pages = 129072 (0x0001f830) IRQ stack: p0x107fe000 v0xc07fe000 ABT stack: p0x107ff000 v0xc07ff000 UND stack: p0x10800000 v0xc0800000 SVC stack: p0x10801000 v0xc0801000 Creating L1 page table at 0x107d0000 Mapping kernel Constructing L2 page tables undefined page pmap [ using 729236 bytes of bsd ELF symbol table ] board type: 240497260 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2016 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 6.0 (GENERIC) #285: Mon Jul 25 12:12:03 AEST 2016 j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/GENERIC real mem = 536870912 (512MB) avail mem = 517976064 (493MB) mainbus0 at root: Wandboard i.MX6 Dual Lite Board rev B1 cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core) cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache cortex0 at mainbus0 ampintc0 at cortex0 nirq 160 amptimer0 at cortex0: tick rate 396000 KHz armliicc0 at cortex0: rtl 8 waymask: 0x0000000f imx0 at mainbus0 imxccm0 at imx0: imx6 rev 1.1 CPU freq: 792 MHz imxiomuxc0 at imx0 imxocotp0 at imx0 simplebus0 at mainbus0: "soc" simplebus1 at simplebus0: "aips-bus" simplebus2 at simplebus1: "spba-bus" imxuart0 at simplebus2: console imxgpio0 at simplebus1 imxgpio1 at simplebus1 imxgpio2 at simplebus1 imxgpio3 at simplebus1 imxgpio4 at simplebus1 imxgpio5 at simplebus1 imxgpio6 at simplebus1 imxdog0 at simplebus1 simplebus3 at simplebus1: "anatop" simplebus4 at simplebus0: "aips-bus" imxehci0 at simplebus4 usb0 at imxehci0: USB revision 2.0 uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1 imxehci1 at simplebus4 usb1 at imxehci1: USB revision 2.0 uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1 fec0 at simplebus4 fec0: address 00:1f:7b:b0:08:52 atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4 imxesdhc0 at simplebus4 imxesdhc0: 198 MHz base clock sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma imxesdhc1 at simplebus4 imxesdhc1: 198 MHz base clock sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma imxesdhc2 at simplebus4 imxesdhc2: 198 MHz base clock sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma imxiic0 at simplebus4 iic0 at imxiic0 imxiic1 at simplebus4 iic1 at imxiic1 "fsl,sgtl5000" at iic1 addr 0xa not configured imxuart1 at simplebus4 simplebus5 at mainbus0: "regulators" sdmmc1: can't enable card scsibus0 at sdmmc0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed sd0: 1910MB, 512 bytes/sector, 3911680 sectors scsibus1 at sdmmc2: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU08G, 0080> SCSI2 0/direct fixed sd1: 7580MB, 512 bytes/sector, 15523840 sectors vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets boot device: sd0 root on sd1a (8202d1873078fd2f.a) swap on sd1b dump on sd1b WARNING: CHECK AND RESET THE DATE! Automatic boot in progress: starting file system checks. /dev/sd1a (8202d1873078fd2f.a): file system is clean; not checking /dev/sd1j (8202d1873078fd2f.j): file system is clean; not checking /dev/sd1d (8202d1873078fd2f.d): file system is clean; not checking /dev/sd1f (8202d1873078fd2f.f): file system is clean; not checking /dev/sd1g (8202d1873078fd2f.g): file system is clean; not checking /dev/sd1h (8202d1873078fd2f.h): file system is clean; not checking /dev/sd1e (8202d1873078fd2f.e): file system is clean; not checking setting tty flags pf enabled starting network reordering libraries: done. openssl: generating isakmpd/iked RSA keys... done. ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519 starting early daemons: syslogd pflogd ntpd. starting RPC daemons:. savecore: no core dump checking quotas: done. clearing /tmp kern.securelevel: 0 -> 1 creating runtime link editor directory cache. preserving editor files. starting network daemons: sshd smtpd sndiod. Path to firmware: http://firmware.openbsd.org/firmware/6.0/ No devices found which need firmware files to be downloaded. starting local daemons: cron. Sun Jul 24 04:03:44 BRT 2016 OpenBSD/armv7 (wbs.my.domain) (console) login: root Password: OpenBSD 6.0 (GENERIC) #285: Mon Jul 25 12:12:03 AEST 2016 Welcome to OpenBSD: The proactively secure Unix-like operating system. Please use the sendbug(1) utility to report bugs in the system. Before reporting a bug, please try to reproduce it with the latest version of the code. With bug reports, please try to ensure that enough information to reproduce the problem is enclosed, and if a known fix for it exists, include that as well. You have mail. # ifconfig fec0 fec0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 lladdr 00:1f:7b:b0:08:52 index 1 priority 0 llprio 3 groups: egress media: Ethernet autoselect (none) status: no carrier inet 192.168.1.24 netmask 0xffffff00 broadcast 192.168.1.255 # vmstat -zi interrupt total rate irq1023/spur 43 0 irq58/imxuart0 43 0 irq75/imxehci0 0 0 irq72/imxehci1 0 0 irq150/fec0 3 0 irq54/imxesdhc0 40 0 irq55/imxesdhc1 4 0 irq56/imxesdhc2 22178 28 irq60/imxuart1 0 0 irq29/tick 156596 199 Total 178907 228 # -- db
