On 2021-12-03 07:47, iw1...@gmail.com wrote:
This is what I obtain from the two commands. In the image loader
command, if I do not specify the image it takes automatically the XG,
which is the same I used to program the FPGA with Vivado (2x10G).
|abusso@ttclabsdr:~$ uhd_usrp_probe|
|linux; GNU C++ version 7.3.0; Boost_106501; UHD_003.010.003.000-0-unknown|
|-- X300 initialization sequence...|
|-- Determining maximum frame size... 8000 bytes.|
|-- Setup basic communication...|
|-- Loading values from EEPROM...|
|-- Setup RF frontend clocking...|
|-- Radio 1x clock:200|
|-- [DMA FIFO] Running BIST for FIFO 0... pass (Throughput: 1302.6MB/s)|
|-- [DMA FIFO] Running BIST for FIFO 1... pass (Throughput: 1304.5MB/s)|
|-- [RFNoC Radio] Performing register loopback test... pass|
|-- [RFNoC Radio] Performing register loopback test... pass|
|-- [RFNoC Radio] Performing register loopback test... pass|
|-- [RFNoC Radio] Performing register loopback test... pass|
|-- Performing timer loopback test... pass|
|-- Performing timer loopback test... pass|
|_____________________________________________________|
|/|
|| Device: X-Series Device|
|| _____________________________________________________|
|| /|
|| | Mboard: X310|
|| | revision: 11|
|| | revision_compat: 7|
|| | product: 30818|
|| | mac-addr0: 00:80:2f:30:8e:01|
|| | mac-addr1: 00:80:2f:30:8e:02|
|| | gateway: 192.168.10.1|
|| | ip-addr0: 192.168.10.2|
|| | subnet0: 255.255.255.0|
|| | ip-addr1: 192.168.20.2|
|| | subnet1: 255.255.255.0|
|| | ip-addr2: 192.168.30.2|
|| | subnet2: 255.255.255.0|
|| | ip-addr3: 192.168.40.2|
|| | subnet3: 255.255.255.0|
|| | serial: 31D7872|
|| | name: TTC_X310|
|| | FW Version: 5.1|
|| | FPGA Version: 33.0|
|| | RFNoC capable: Yes|
|| ||
|| | Time sources: internal, external, gpsdo|
|| | Clock sources: internal, external, gpsdo|
|| | Sensors: ref_locked|
|| | _____________________________________________________|
|| | /|
|| | | RX Dboard: A|
|| | | ID: UBX-160 v2 (0x007e)|
|| | | Serial: 31D5853|
|| | | _____________________________________________________|
|| | | /|
|| | | | RX Frontend: 0|
|| | | | Name: UBX RX|
|| | | | Antennas: TX/RX, RX2, CAL|
|| | | | Sensors: lo_locked|
|| | | | Freq range: 10.000 to 6000.000 MHz|
|| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB|
|| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz|
|| | | | Connection Type: IQ|
|| | | | Uses LO offset: No|
|| | | _____________________________________________________|
|| | | /|
|| | | | RX Codec: A|
|| | | | Name: ads62p48|
|| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB|
|| | _____________________________________________________|
|| | /|
|| | | RX Dboard: B|
|| | | ID: UBX-160 v2 (0x007e)|
|| | | Serial: 31D5807|
|| | | _____________________________________________________|
|| | | /|
|| | | | RX Frontend: 0|
|| | | | Name: UBX RX|
|| | | | Antennas: TX/RX, RX2, CAL|
|| | | | Sensors: lo_locked|
|| | | | Freq range: 10.000 to 6000.000 MHz|
|| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB|
|| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz|
|| | | | Connection Type: IQ|
|| | | | Uses LO offset: No|
|| | | _____________________________________________________|
|| | | /|
|| | | | RX Codec: B|
|| | | | Name: ads62p48|
|| | | | Gain range digital: 0.0 to 6.0 step 0.5 dB|
|| | _____________________________________________________|
|| | /|
|| | | TX Dboard: A|
|| | | ID: UBX-160 v2 (0x007d)|
|| | | Serial: 31D5853|
|| | | _____________________________________________________|
|| | | /|
|| | | | TX Frontend: 0|
|| | | | Name: UBX TX|
|| | | | Antennas: TX/RX, CAL|
|| | | | Sensors: lo_locked|
|| | | | Freq range: 10.000 to 6000.000 MHz|
|| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB|
|| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz|
|| | | | Connection Type: QI|
|| | | | Uses LO offset: No|
|| | | _____________________________________________________|
|| | | /|
|| | | | TX Codec: A|
|| | | | Name: ad9146|
|| | | | Gain Elements: None|
|| | _____________________________________________________|
|| | /|
|| | | TX Dboard: B|
|| | | ID: UBX-160 v2 (0x007d)|
|| | | Serial: 31D5807|
|| | | _____________________________________________________|
|| | | /|
|| | | | TX Frontend: 0|
|| | | | Name: UBX TX|
|| | | | Antennas: TX/RX, CAL|
|| | | | Sensors: lo_locked|
|| | | | Freq range: 10.000 to 6000.000 MHz|
|| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB|
|| | | | Bandwidth range: 160000000.0 to 160000000.0 step 0.0 Hz|
|| | | | Connection Type: QI|
|| | | | Uses LO offset: No|
|| | | _____________________________________________________|
|| | | /|
|| | | | TX Codec: B|
|| | | | Name: ad9146|
|| | | | Gain Elements: None|
|| | _____________________________________________________|
|| | /|
|| | | RFNoC blocks on this device:|
|| | ||
|| | | * DmaFIFO_0|
|| | | * Radio_0|
|| | | * Radio_1|
|| | | * DDC_0|
|| | | * DDC_1|
|| | | * DUC_0|
|| | | * DUC_1|
|abusso@ttclabsdr:~$ uhd_image_loader --args "type=x300,addr=192.168.30.2"|
|linux; GNU C++ version 7.3.0; Boost_106501; UHD_003.010.003.000-0-unknown|
|Unit: USRP X310 (31D7872, 192.168.30.2)|
|FPGA Image: /usr/share/uhd/images/usrp_x310_fpga_XG.bit|
|failed.|
|Error: RuntimeError: Device reported an error during initialization.|
|abusso@ttclabsdr:~$|
_______________________________________________
USRP-users mailing list --usrp-users@lists.ettus.com
To unsubscribe send an email tousrp-users-le...@lists.ettus.com
What happens if you download fresh images (uhd_images_downloader), and
try this again?
When the device is running, if you ping it, do you get any errors
(packet drops)?
_______________________________________________
USRP-users mailing list -- usrp-users@lists.ettus.com
To unsubscribe send an email to usrp-users-le...@lists.ettus.com
