Hello, thank you very much for your prompt reply.
i copied the .mender file by using the "scp" command. Yes, i am running the command on the USRP. I am not sure if this is a problem but --initially when i created the .mender file, the host was running the UHD 3.14.0.0 and the USRP had 3.14.1.0. This is when the problem appeared first. Then i changed the uhd to 3.14.1.0 on the host to match exactly the UHD on the usrp, but the error still persists (or course i deleted the old file from the usrp). any ideas? best, P. On Wed, Jul 15, 2020 at 4:53 PM Marcus D. Leech via USRP-users < usrp-users@lists.ettus.com> wrote: > On 07/15/2020 08:12 AM, Pavlos Basaras via USRP-users wrote: > > Dear community, > > > > i am using the usrp n310 device. I am following the start up guide > > from > > > https://kb.ettus.com/USRP_N300/N310/N320/N321_Getting_Started_Guide#Setting_up_a_Serial_Console_Connection > > for the initial setup of the usrp. > > > > I completed the installation instructions for the host from > > > https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux > > < > https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_%28UHD_and_GNU_Radio%29_on_Linux > > > > everything seemed ok. > > > > I can connect to the device through both ssh and by the serial port. > > > > I am trying to use mender to update the filesystem at the usrp device. > > > > I executed the command: sudo uhd_images_downloader -t mender -t n3xx > --yes > > at the host to obtain usrp_n3xx_fs.mender, which i then copied to the > > usrp. > > > > At the usrp i am using the command: mender -rootfs > > /home/root/usrp_n3xx_fs.mender > > to start the update of the system but i have the following > > incompatibility issue : > > > > ERRO[0000] Installation failed: installer: failed to read and install > > update: installer: image (device types [ni-sulfur-rev6-mender > > ni-sulfur-rev5-mender ni-sulfur-rev4-mender ni-sulfur-rev3-mender > > ni-sulfur-rev6 ni-sulfur-rev5 ni-sulfur-rev4 ni-sulfur-rev3]) not > > compatible with device ni-sulfur-rev11-mender module=rootfs > > ERRO[0000] installer: failed to read and install update: installer: > > image (device types [ni-sulfur-rev6-mender ni-sulfur-rev5-mender > > ni-sulfur-rev4-mender ni-sulfur-rev3-mender ni-sulfur-rev6 > > ni-sulfur-rev5 ni-sulfur-rev4 ni-sulfur-rev3]) not compatible with > > device ni-sulfur-rev11-mender module=main > > > > > > How can i resolve this? > > > > > > Details on the UHD intalled on both the host and the usrp device" > > > > HOST computer uhd: [INFO] [UHD] linux; GNU C++ version 5.4.0 20160609; > > Boost_105800; UHD_3.14.1.HEAD-0-g0347a6d8 > > USRP uhd: [INFO] [UHD] linux; GNU C++ version 7.3.0; Boost_106600; > > UHD_3.14.1.1-0-g0347a6d8 > > > > > > all the best, > > Pavlos. > > > This seems a bit odd. > > Two things: > > (A) How did you copy the .mender file over to the usrp? > (B) (This seems really dumb, and I apologize in advance) are you sure > that you're running the mender command ON the USRP? > > > > _______________________________________________ > USRP-users mailing list > USRP-users@lists.ettus.com > http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com >
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
