[RE-wrenches] Testing AGMs

Wrenches, We have a client with a string of sealed L16s and he believes he may have a weak or failed cell. What’s the best way to test or check these batteries, since there is no electrolyte to draw out. We don’t install many AGMs, in fact, steer the client away from them, usually. Jeremy

[RE-wrenches] EMP and PV modules

I’ve done a quick search of the archives, but does anyone know of the the effects of an EMP PULSE on a module? We’ve got a potentially large project to look forward to, and one developer is very concerned Jeremy Rodriguez Solar installation / Design Expert All Solar, Inc. 1463 M St Penrose

Re: [RE-wrenches] Rapid Shutdown Off Grid

We’ve installed many Midnite BHs with the disconnecting combiners (and battery disco modules pre 2017 NEC.) Recently we set up a roof mounted array with the disconnecting HV combiner along with the SOB for the PV Side of the CC. Worked well. I’d be interested in the OB gear as well. Jeremy

[RE-wrenches] CC Temp Comp value

stage quickly, BTW. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. ___ List sponsored by Redwood Alliance List Address: RE-wrenches@lis

Re: [RE-wrenches] PIKA wind turbine.

We’ve installed 5 of them. Good machine, and they were worth the extensive lead times. Pika is not focused on their turbine any more, and I’ve been told they will not produce any more, unless they have a large project to fulfill. Jeremy Rodriguez Solar Installation / Design Expert All Solar

[RE-wrenches] SW 275BOB

I’m in need of two Solar World SW275. BOB modules. Please contact me off list if you have any. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] AC Coupling with Dual Radians

I have been reading Outbacks AC coupling note. It refers to using only a single Radian Inverter. Is it possible to duplicate the equipment if more PV is installed, and use two Radians, with their outputs paralleled to the critical loads panel? I see it recommends 6Kw of PV with an 8048 Radian Jer

[RE-wrenches] Extending Midnite BTS

Is it ok to extend the battery temp sensor wire for a classic controller? Length might be around 25 ft max. Original is 15ft. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

Re: [RE-wrenches] WEEB-ADR clips

You should check with your electrical supplier. We have sourced some weebs and I recall they were burndy Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Apr 9, 2019, at 6:06 PM,

Re: [RE-wrenches] Cutting rail

Pre cut the rails at ground level with your circular saw. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Jun 12, 2019, at 11:32 PM, frenergy mailto:frene...@psln.com>>

[RE-wrenches] Wind Gen Support

Hello, Has anyone been in touch with Xzeres Wind Power lately? Their phone number seems to lead to a empty cubical. I’ve got a client in So CO in need of help with his 10kw turbine/ SMA Windy Boy inverter set up. If anyone has experience with these, contact me off list. TIA, Jeremy Rodriguez

Re: [RE-wrenches] spaghetti mat

The hotter it is the better. I like it as it softens up and I think it’s Safe to 30 degrees. We have only used it on asphalt. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On

[RE-wrenches] Outback stocking distributor

Hello Can you recommend a distributor for a Radian inverter bypass kit? Our usual no longer sells.What? Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] SMA -41 and TS4

Hello Does anyone know if the SMA ROOFTOP COMMUNICATION KIT works with the new -41 inverters? Regards , Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] Seeking CS modules

Please contact me off list if you have 2 or 3 CS6P 200P mods. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. ___ List sponsored by Re

[RE-wrenches] PV Payback Analysis

Can anyone recommend a quick, easy to use and read. PV Grid Tie payback analysis. Thanks. Jeremy___ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re

Re: [RE-wrenches] Sunwize or industrial PV modules

Try Ameresco Solar Jeremy Rodriguez All Solar, Inc. 1463 M Penrose Colorado 81240 719-372-3808 office 719-372-3804 fax www.asolarelectric.com Jeremy and Amy Rodriguez Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Feb 24, 2015, at 11:44 AM, "Larry" wrote: &

[RE-wrenches] Charging Multiple Battery Banks

e the 24v bank, then once it is fully charged, divert the pv to the secondary controller at the 48v bank. Any comments or recommendations on this would be helpful. Jeremy Rodriguez All Solar Inc. Penrose, CO ___

Re: [RE-wrenches] Charging Multiple Battery Banks

controllers are auto sensing Jerry On Tue, Mar 24, 2015 at 12:11 PM, Jeremy Rodriguez wrote: Wrenches, I have a client that wants to charge a 24v battery bank and a 48v bank with the same array. Different charge controllers, with some type of relay is what I was thinking, and using the controller&#

Re: [RE-wrenches] Charging Multiple Battery Banks

well. 3 years old I've never had this come up in 16 years! Jeremy Rodriguez All Solar, Inc. 1463 M Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Mar 24, 2015, at 5:31 PM, "Ray Walters" wrote: > > What's the reasoning

Re: [RE-wrenches] Charging Multiple Battery Banks

pe of relay could be used? Does it need to be solid state ? I would feel better using some type of control, or as was mentioned, maybe talk him into just hooking everything up to the OB system at the house. The 24v side would be for occasional use only. Thanks for the input! Jeremy Rodriguez

[RE-wrenches] Ice on array

Hello I have a client who has experienced this twice now. After a snow storm, two of his arrays, when brushing snow from, will clear very easy. The third, which is of similar age as one that sheds well, gets ice underneath the snow and is not cleaned as easily. Any ideas? Jeremy Rodriguez

[RE-wrenches] Photowatt Modules

Does anyone know of any Photowatt PWX 12-24v mods? I need one. I know it's a long shot. Thanks. Jeremy Rodriguez All Solar, Inc. 1463 M Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___ List sponsored

[RE-wrenches] Photocom inverter

Does anyone have any contact info for a former Photocom rep? I've got a client with one that's acting up. Regards, Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typo

[RE-wrenches] SMA Sunny Island Sizing

Hello So far I've been unsuccessful in getting SMA to return a call Does anyone have a direct line to one of their design engineers? •Off grid SI/SB 3Phase Help..... Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M Penrose Colorado 81240 Sent by Jeremy

Re: [RE-wrenches] SMA Sunny Island Sizing

x27;t apply to working in the field, but..... Jeremy Rodriguez All Solar, Inc. 1463 M Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Jun 25, 2015, at 4:07 PM, Tump wrote: > > While they recently have down sized their staff I find this surprising

Re: [RE-wrenches] Rapid Shutdown Battery Systems

Here's a link from the CO State Electrical Inspector Supervisor. http://iaeimagazine.org/magazine/2015/01/22/rapid-shutdown-of-pv-systems/ Good article. Seems like off grid pole mount array and battery conductors WILL apply. Jeremy Rodriguez Solar Installation And Design Expert All

[RE-wrenches] Rapid shutdown causing AFCI TEST FAILURE

Greetings! I verified today after replacing an SB6000-12 for a K1 relay open code, that the rapid shutdown circuitry was causing intermittent arc fault test failures. It had done this from day 1 Contact me off list for more information. Jeremy Rodriguez Solar Installation And Design Expert

[RE-wrenches] SWRC50

Hello wrenches, Does anyone have a new or used SW Series remote control cable ? Jeremy Rodriguez All Solar Penrose CO allso...@live.com ___ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email

Re: [RE-wrenches] SWRC50

Definitely need the 50ft version. Thanks Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On Jan 22, 2016, at 11:23 AM, Howie Michaelson mailto:ho...@suncatchervt.com>>

[RE-wrenches] Increasing output Amps, Off Grid

building. 120 v only is fine. He has overloaded the dual 3648 set up once before. I recommended another pair of FX3648 inverters with autoformer. Comments and recommendations appreciated. Thanks in advance Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St P

Re: [RE-wrenches] Increasing output Amps, Off Grid

I spoke with Outback today and I've got some options for sure, from everyone. Thanks! Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Feb 2, 2016, at 8:59 A

Re: [RE-wrenches] Old Net Metering

I would put it in Float mode and let it offset the grid. I don't think it would actually sell unless you select that from the grid use menu. If it's the SW, that is. Study the owners manual Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penros

Re: [RE-wrenches] Specific AC Coupling question

Have installed a 5548 and 6048 XW with IG Plus 10.0 with fair results. On/Off when AC coupled during the test phase. I have not heard any complaints from the homeowner. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy&#

Re: [RE-wrenches] Off-grid generator update?

Check out Gillette generators. Made in Indiana 12.5 kW w Subaru Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On Apr 28, 2016, at 10:20 AM, Lena Wilensky mai

[RE-wrenches] Whisper Turbine Replacement

Hello Does anyone have a recommended replacement turbine for a Whisper 100 or whisper 200? Would be best to have something fit the existing tower, 2.5" sch40, if possible. Thanks in advance! Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Col

[RE-wrenches] Stolen modules, what to do?

. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org C

[RE-wrenches] STP200-18

If anyone he has four Suntech Tech 200–18ub-1 modules please contact me off list Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___

[RE-wrenches] Compressor motor/SW+5548

ed #8 from the Breaker to the pressure switch, about 9ft, with no benefit. The compressor will only start with the tank completely empty. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typo

Re: [RE-wrenches] Compressor motor/SW+5548

Bob Can you elaborate a little on this extension cord idea either here or off-line? Thank you Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On May 30, 2016, at 1:15 PM

[RE-wrenches] Rapid Shutdown equipment restart. BH, Combiner and battery disco.

is lost or not..,.. Seems like the battery disconnect module is most finicky. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___

[RE-wrenches] Hydrometer tube lost in a battery cell..

Wrenches, I will contact Surrette if necessary, but I have a client that lost his hydrometer tube in one of the cells of a 4 V battery, if I recall. industrial, dual container. Is there any risk of damage? Should the tube be removed, if possible? Plastic/ Rubber tube of course. Jeremy

Re: [RE-wrenches] Pass through/transition box for Enphase

How about these? https://idealind.com/us/en/products/wire-termination/set-screw-connectors/set-screw-connectors/set-screw-wire-connectors.aspx Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typo

[RE-wrenches] OB FW Lightning Protection w/ EPanel

the sides of the OB ACA vs. where they originally land. Any thoughts or experiences would be appreciated! Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

Re: [RE-wrenches] OB FW Lightning Protection w/ EPanel

This is for an existing system. They are wanting to install the outback product on FXs installed with E panels They currently have Midnite arrestors. I know! Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone.

Re: [RE-wrenches] OB FW Lightning Protection w/ EPanel

Do you if the wiring from the E panel will reach with the AC conduit box in place on the FX? Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On Aug 27, 2016, at 10:02 PM

[RE-wrenches] OB Hub4 cover

If anyone has a hub 4 wire cover, with no pieces cut out, please contact me off list. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] Module search

Anyone have any Poly CSIs in the 250-260w range? Looking for three. please contact me off list. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] Galvo 3.1 manual

Hello I'm reaching out to an SMA rep on the list to contact me off list. I have a client in need of a hard copy of the operators manual for his new Galvo 3.1 inverter. Missing in the box. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado

Re: [RE-wrenches] Galvo 3.1 manual

Opps. I mean Fronius ! Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Apr 11, 2017, at 7:37 PM, Jeremy Rodriguez wrote: > > Hello > I'm reaching ou

Re: [RE-wrenches] Fuse for 48 V DC

How about Midnite din mount 150vdc breakers. 1-63 amp range. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! On May 24, 2017, at 11:59 AM, Drake mailto:drake.ch

[RE-wrenches] Apollo Contact

Hello, I have a potential client needed some help with an Apollo charge controller. If anyone has a current phone number I'd appreciate it. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for

[RE-wrenches] Suntech modules

If Anyone has some Suntech STP-200-220/18 modules (3) Please contact me off list. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] Sanyo HIT210N dimensions

Hello Does anyone happen to have access to a HIT210N module they could measure? I'm in need of the mounting hole dims. See below. [page1image480] Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for

Re: [RE-wrenches] OFF-LINE REPLY - Re: Sanyo HIT210N dimensions

I have seen all the spec sheets. I need the horizontal, hole to hole dimensions. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Aug 21, 2017, at 8:01 PM, Exeltec

Re: [RE-wrenches] OFF-LINE REPLY - Re: Sanyo HIT210N dimensions

Me too ! but DPW wants the horizontal hole to hole spacing as if the module is in portrait mode. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! > On Aug 23, 2017, at

[RE-wrenches] SolarEdge tech help

Does anyone have a dealer only phone number to reach SolarEdge tech support? Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___

[RE-wrenches] Photowatt Contact

Does anyone have a contact at Photowatt (France)? Looking for possible warranty coverage. Jeremy Rodriguez Solar Installation And Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

Re: [RE-wrenches] AFCI problems with SMA RSB

Have you tried updating the inverter via an SD card. SMA tech support emailed me a link. We had a similar problem but don't think it had anything to do with the RSB, though this one used the remote switch, so I'm not sure if it's the same RSB you refer to. Jeremy R

[RE-wrenches] Pika Support by chance?

If anyone has any info on how to get a hold of The former PIKA ENERGY support group, please contact me off list. Or if anyone knows where one could get one of their inverters rebuilt/repaired let me know. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose

Re: [RE-wrenches] Pika Support by chance?

This is for a PIKA wind turbine. We have since been in contact with that support group at Generac. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Sep 29, 2020, at 7:27 AM,

[RE-wrenches] DPW rack adjustment

Does anyone have any trick to adjusting the tilt angle of the TPM4 pole mounts? These are the racks with the aluminum beam (strongback) with slots for the bolts. We have tried anti seize, and cutting the heads of the bolts square in attempts to help with adjustment. Help! Jeremy Rodriguez

Re: [RE-wrenches] Metal roof/self taping screws

We’ve had good luck with thread cutting screws. Found some 3/8“ diameter that worked good with the LFeet and butyl tape. Need to pre drill the perlin. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for

Re: [RE-wrenches] Protecting New Roofing during Summe

Spaghetti walk pad. https://www.bestmaterials.com/detail.aspx?ID=18959 Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1463 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Mar 8, 2021, at 4:02 PM, Jeremy Coxon wrote: We inst

[RE-wrenches] Pressure pump and Magnum 4448 causing washer shutdown

pulling from a cistern and is a 115V unit. Not sure of the pressure tank size or pump hp rating. •ME 4448 PAE with one string of ~500 AH battery cap. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typo

[RE-wrenches] Drain Back Solar Thermal

Wrenches Anyone with experience in design of evac tube systems with atmospheric tanks, can you please contact me off list? I need some advice / schematics for heat dissipation strategies. Regards, Jeremy Rodriguez Solar Installation / Design All Solar, Inc. 1453 M St Penrose Colorado 81240

[RE-wrenches] High to normal SG

cell here. What else can be checked , battery wise? Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. ___ List sponsored by Redwood Alliance

Re: [RE-wrenches] High to normal SG

Deka 8L16 Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Jul 21, 2021, at 8:24 AM, Jay wrote:  And what color is the electrolyte? On Jul 21, 2021, at 8:02 AM, Jay wrote:

Re: [RE-wrenches] High to normal SG

Okay Is there a quick way to run on just one string? Or should I say determine which batteries would make a good string. I’d normally say, find the best batteries based on specific gravity and use them, but in this case all specific gravity‘s seem good. Jeremy Rodriguez Solar Installation

Re: [RE-wrenches] High to normal SG

Steve, Do you measure voltage of each battery with them disconnected or as is. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Jul 21, 2021, at 8:59 AM, Steve Higgins

Re: [RE-wrenches] High to normal SG

when I checked cells. 1.265- 1.275 No residue on the caps I did note that all the positive Posts have “grown” and cause the case to start cracking slightly around the post. I’ve seen this a lot with Deka. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado

Re: [RE-wrenches] Deka 8L16

clear when I checked cells. 1.265- 1.275 No residue on the caps I did note that all the positive Posts have “grown” and cause the case to start cracking slightly around the post. I’ve seen this a lot with Deka. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose

[RE-wrenches] DC Rating of Square D QO?

nce. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. ___ List sponsored by Redwood Alliance Pay optional member dues here: http://re-wren

[RE-wrenches] LiFePo4 and FNDC

. Happy holidays Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. ___ List sponsored by Redwood Alliance Pay optional member dues here: http

Re: [RE-wrenches] LiFePo4 and FNDC

Iron Edison RE Volt 10.2 Battery Amp Hours - 600 Charged Voltage - 56 VDC Charge return amps- 30A Time- 6 minutes Charge Factor- 99% Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand

[RE-wrenches] Midnite HV combiners

If anyone has any leftover stock of the midnite MNPV4HV-DISCO3R-DLX-PSB combiner, please contact me off list. Regards, Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shor

[RE-wrenches] PAE series surge capacity/ power factor ?

the mains panel. 4448 PAE with one string of 6CS21P Batteries. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado Sent by Jeremy's iPhone. Sorry for typos and shorthand! ___ List sponsored by Redwood All

Re: [RE-wrenches] PAE series surge capacity/ power factor ?

So the issue ended up being , as far as we can tell at this point , a loose neutral connection at the first load distribution panel feeding all loads after the inverter. Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's i

Re: [RE-wrenches] Rapid Shutdown for Off-grid systems

What about the PV circuits that leave the combiner and are ran on or in a building to the CC Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Feb 1, 2022, at 4:07 PM, Brian Me

Re: [RE-wrenches] Rapid Shutdown for Off-grid systems

Just a rated disco at the ground mount? Labeled as the rapid shutdown switch? That’s too simple! In Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Feb 1, 2022, at 6:49 PM,

[RE-wrenches] SMA SBxx-US-41 inverters and Tigo TS4A-O operation

interface board. Can someone clarify if the CCA + Gateway are needed, or can I use the GIB to get the gateway communication established. Thanks in advance ! Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typo

Re: [RE-wrenches] SMA inverters and Tigo TS4A-O operation

Michael If we can find new old stock of a roof top comm kit, would it work with the Inverter? Jeremy Rodriguez Solar Installation / Design Expert All Solar, Inc. 1453 M St Penrose Colorado 81240 Sent by Jeremy's iPhone. Sorry for typos and shorthand. On Mar 18, 2022, at 12:11 PM,

[RE-wrenches] 3 Phase Grid Tie with Battery Backup

Anyone know of a system for Battery Backup that can also be grid tied for 3 phase? Our local Utilitly Co. wants system voltage to match service voltage. Thanks in advance! Jeremy___ List sponsored by Home Power magazine List Address: RE-wrenches@list

Re: [RE-wrenches] 3 Phase Grid Tie with Battery Backup

Jeff, That was my first choice, but I was told by Outback that they do not offer a 120/208 inverter(s). I have not set up a three phase system yet, so bare with me please. I was going to contact SMA next. Jeremy - Original Message - From: "Jeff Oldham" To: ; Sent: Monday, Febr

Re: [RE-wrenches] 3 Phase Grid Tie with Battery Backup

(motors will reverse and you may fry the OB transfer relay) Next time you call outback ask a tech if you can slave the GVFX to make 3 phase, --- On Mon, 2/15/10, All Solar Inc. Jeremy Rodriguez wrote: From: All Solar Inc. Jeremy Rodriguez Subject: Re: [RE-wrenches] 3 Phase Grid Tie wi

Re: [RE-wrenches] 3 Phase Grid Tie with Battery Backup

Positive Energy, Inc. 3201 Calle Marie Santa Fe, New Mexico 87507 505 424-1112 www.positiveenergysolar.com All Solar Inc. Jeremy Rodriguez wrote: Thanks Darryl, Allen, would you have to use 3 Sunny Islands? one for each phase? The Utility wants a single inverter.

[RE-wrenches] 3 Phase Answers

Thanks to all for the help. Its going to have to be an IG Plus. 208V Delta: 120V WYE config. Wait til June for it... Jeremy ___ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settin

[RE-wrenches] Fw: 3 Phase Grid Tie with Battery Backup

- Original Message - From: "All Solar Inc. Jeremy Rodriguez" To: Sent: Tuesday, February 16, 2010 10:12 AM Subject: Re: [RE-wrenches] 3 Phase Grid Tie with Battery Backup Darryl, I would say the utility is still learning. 10kw of PV to put into the grid or as large as

Re: [RE-wrenches] Kohler 10ERG and RES Models

We now use Gillette Generators. Prime power warranty, 12kw, Honda Engine, 2 wire start, enclosed, Nice units. No issues so far. Jeremy All Solar Inc. Jeremy and Amy Rodriguez 1463 M St Penrose, CO 81240 www.asolarelectric.com Phone 719-372-3808 Fax 719-372-3804 Email allso...@scswifi.net Email

Re: [RE-wrenches] AFCI compatibility with modified waveforminverters

Will not work with Xantrex TR series, formerly DR. After the inverter was on for about 5 minutes, the AFCI breakers began tripping. Jeremy - Original Message - From: "Darryl Thayer" To: "RE-wrenches" Sent: Sunday, March 28, 2010 10:53 PM Subject: Re: [RE-wrenches] AFCI compatibility

Re: [RE-wrenches] Kohler Generator Issues

Jeff, check out Gillette Generators. Prime power warranty. and 'ok with inverter' Jeremy - Original Message - From: "Jeff Yago" To: "RE-wrenches" Sent: Monday, March 29, 2010 8:53 AM Subject: Re: [RE-wrenches] Kohler Generator Issues Although we have specified and included Kohler R

[RE-wrenches] 120V KWH meter wiring

Wrenches Can someone please advise on the proper way to wire a meter to read 120V inverter output. This is actually for production (RECs) Thanks in advance Jeremy Rodriguez Sent via BlackBerry. Sorry for typos and shorthand! ___ List sponsored by Home

[RE-wrenches] Sealed Battery Issues

Wrenches Can someone advise how to best check for a bad cell and or battery in a bank of sealed AGMs I have not installed many of these and have a client that I did for about a year ago. One looks like it may have leaked out some fluid from the top as it has some white residue there Jeremy

[RE-wrenches] Lithium Batteries

I have a request for Lithium batteries (ion?). Not sure how to respond. The application is an off grid, part time mountain home Any thoughts? Thank you Jeremy Ridriguez All Solar Colorado Sent via BlackBerry. Sorry for typos and shorthand! ___ List spon

Re: [RE-wrenches] Low power production at a winery: DC voltage drop upon SB6000 start-up

Look for burnt or hot spots near the top of the modules under the Jbox area. We have replaced a lot of modules of that age Ameresco solar is supposedly making the replacement modules Jeremy All Solar Sent via BlackBerry. Sorry for typos and shorthand! -Original Message- From: "SunHarvest"

Re: [RE-wrenches] Monopole for Whisper Turbines

Ya! The guy from Arizona that designed the Up Tower Jbox. I will try to dig up some info on him too. Thanks! Jeremy All Solar Sent via BlackBerry. Sorry for typos and shorthand! -Original Message- From: Tom Duffy Sender: re-wrenches-boun...@lists.re-wrenches.orgDate: Mon, 23 Jul 2012 2

Re: [RE-wrenches] Alternative to CT-104 Crimps

Ilsco ULT-4 Jeremy All Solar Colorado Sent via BlackBerry. Sorry for typos and shorthand! -Original Message- From: Jason Szumlanski Sender: re-wrenches-boun...@lists.re-wrenches.orgDate: Thu, 2 Aug 2012 09:39:26 To: RE-wrenches Reply-To: RE-wrenches Subject: [RE-wrenches] Alternative t

[RE-wrenches] Are they still in Business? AAA solar

Anyone know if AAA (semco) is still operating? Tried to order an Air Collector system and all the numbers are down or disconnected Jeremy Rodriguez All Solar Sent via BlackBerry. Sorry for typos and shorthand! ___ List sponsored by Home Power magazine

Re: [RE-wrenches] Thermal storage water stabilizer

e had some tanks in the field for years. Jeremy Rodriguez All Solar Sent via BlackBerry. Sorry for typos and shorthand! -Original Message- From: Will White Sender: re-wrenches-boun...@lists.re-wrenches.orgDate: Mon, 13 Aug 2012 12:29:22 To: RE-wrenches Reply-To: RE-wrenches Subject: Re

[RE-wrenches] Trace ICM cable

Hello, Anyone have a source for a Xantrex PS series inverter control panel cable? It's the 25 pin cable. Looks like an old printer cable. Also any luck with splicing (repairing) them as it's been cut. Contact me off list if u have one. allso...@scswifi.net Jeremy R All Solar Sent via BlackBerry

  1   2   >