Re: [OpenWrt-Devel] Gigaset SX763

Al 13/05/11 21:13, En/na Andrej Vlašić ha escrit: I'm not sure that's the correct thing to do: in the ar71xx architecture (using ath9k), they're writing some register that modify the pci id, maybe in your file there's also some fixup data? Thanx for the info about wlan, I found out that in ori

Re: [OpenWrt-Devel] Gigaset SX763

On 13.5.2011. 20:02, Luca Olivetti wrote: > Oh, I thought you wanted to dump the flash, not restore it, sorry, I've > no suggestion for that. > (Actually, if it's based on the danube, it should have a mode in which > you can send the code via serial, and this mode doesn't depend on the > flash, how

Re: [OpenWrt-Devel] Gigaset SX763

Al 11/05/11 00:48, En/na Luca Olivetti ha escrit: > That seems to be the case: the file starts with > > 0x13 0x00 0x8c 0x16 -> 168c:0013 > > which is a correct pci id for the ar5212 And for the ar2414 (the one the sx763 is using), see here: http://linuxwireless.org/en/users/Drivers/ath5k/devi

Re: [OpenWrt-Devel] Gigaset SX763

Al 11/05/11 00:38, En/na Luca Olivetti ha escrit: > Al 11/05/11 00:29, En/na Luca Olivetti ha escrit: >> Al 10/05/11 23:36, En/na Andrej Vlašić ha escrit: >> >>> Mac address could be read from nvram (both primary and secondary >>> bootloader are modified u-boot), but the eeprom_data is the problem.

Re: [OpenWrt-Devel] Gigaset SX763

Al 11/05/11 00:29, En/na Luca Olivetti ha escrit: > Al 10/05/11 23:36, En/na Andrej Vlašić ha escrit: > >> Mac address could be read from nvram (both primary and secondary >> bootloader are modified u-boot), but the eeprom_data is the problem. >> I dunno how to locate it inside my binary, is there

Re: [OpenWrt-Devel] Gigaset SX763

Al 10/05/11 23:36, En/na Andrej Vlašić ha escrit: > Mac address could be read from nvram (both primary and secondary > bootloader are modified u-boot), but the eeprom_data is the problem. > I dunno how to locate it inside my binary, is there any special hex > value which represents that? It shoul

Re: [OpenWrt-Devel] Gigaset SX763

On 8.5.2011. 0:41, Luca Olivetti wrote: > Al 07/05/11 23:23, En/na Andrej Vlašić ha escrit: >> Also this board doesn't have wlan eeprom, instead it is read by a wlan >> driver from a file inside fw. If someone has some answers on how to modify >> current ath5k driver, would like to know. > > The

Re: [OpenWrt-Devel] Gigaset SX763

Al 10/05/11 17:25, En/na Andrej Vlašić ha escrit: > Ok so I looked at that code, and below "// set clock gating" and there is: > // set power > writel(readl(DANUBE_PMU_PWDCR) & ~0x1, DANUBE_PMU_PWDCR); > writel(readl(DANUBE_PMU_PWDCR) & ~0x40, DANUBE_PMU_PWDCR); > writel(readl(DANU

Re: [OpenWrt-Devel] Gigaset SX763

2011/5/9 John Crispin > > > Another question about usb power. > > Is it possible that on my board USB clock gating is different than one > set > > in current dwc_otg_ifx.c. > > There it says: > > // set clock gating > > writel(readl(DANUBE_CGU_IFCCR) | 0x30, DANUBE_CGU_IFCCR); > > > > On

Re: [OpenWrt-Devel] Gigaset SX763

Al 10/05/11 00:51, En/na Luka Perkov ha escrit: > The board has standard EJTAG pinout. With urjtag I can dump only part of > flash: If the board uses the brn bootloader, maybe you can use my quick'n'dirty tool to dump the flash: http://code.google.com/p/brndumper/ Bye -- Luca

Re: [OpenWrt-Devel] Gigaset SX763

On Sat, May 07, 2011 at 11:23:36PM +0200, Andrej Vlašić wrote: > I'm trying to set up openwrt on this router, it is based on Lantiq Xway > Danube Soc ( PSB50702 E), and manufactured by Sagem(previously by Siemens). > Wiki page is here http://wiki.openwrt.org/toh/gigaset/sx76x > > I already managed

Re: [OpenWrt-Devel] Gigaset SX763

2011/5/9 John Crispin > > try adding printk("foo %d\n", pin); between the "// GPIOs" and the "if > (" and see what the bootlog says > ___ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/op

Re: [OpenWrt-Devel] Gigaset SX763

I'm curious about this box, it looks very interesting as a replacement for my current ADSL modem/router which is one of the last non-Free computer I use daily. Is the ADSL modem working well under OpenWRT? And what about the FXO/FXS ports? Stefan

Re: [OpenWrt-Devel] Gigaset SX763

> Note that those 3 leds are controlled by the ebu driver, and I assigned them > to the gpio_led structure, i.e.: > > static struct gpio_led > arv7518pw_leds_gpio[] __initdata = { > { .name = "soc:green:power", .gpio = 2, .active_low = 1, }, > { .name = "soc:green:adsl", .gpio = 4

Re: [OpenWrt-Devel] Gigaset SX763

Al 09/05/11 17:14, En/na John Crispin ha escrit: >> >> The next question is, how can I control (some of) the leds from an >> userspace program? >> Opening the /sys/class/leds//trigger file and alternatively >> writing "none" or "default-on"? >> Or the same but with the "brightness" file? >> Writin

Re: [OpenWrt-Devel] Gigaset SX763

On 09/05/11 20:01, John Crispin wrote: > >> Another question about usb power. >> Is it possible that on my board USB clock gating is different than one set >> in current dwc_otg_ifx.c. >> There it says: >> // set clock gating >> writel(readl(DANUBE_CGU_IFCCR) | 0x30, DANUBE_CGU_IFCCR); >>

Re: [OpenWrt-Devel] Gigaset SX763

> Another question about usb power. > Is it possible that on my board USB clock gating is different than one set > in current dwc_otg_ifx.c. > There it says: > // set clock gating > writel(readl(DANUBE_CGU_IFCCR) | 0x30, DANUBE_CGU_IFCCR); > > On mine board it says: > > // set cl

Re: [OpenWrt-Devel] Gigaset SX763

2011/5/8 Andrej Vlašić > I tried 29 again now, and no power, also tried some others, nothing. > > If someone want's to see here is how power is set in original fw: > http://pastebin.com/00vJxdYa Another question about usb power. Is it possible that on my board USB c

Re: [OpenWrt-Devel] Gigaset SX763

On 09/05/11 16:59, Luca Olivetti wrote: > Al 09/05/2011 0:31, En/na Luca Olivetti ha escrit: > >> It turns out that the ebu, in the gpio_led structure, uses gpio starting >> from 32, so defining "fake" leds using gpios 32-40 I could map all >> missing >> leds. >> Since they're active low, I used l

Re: [OpenWrt-Devel] Gigaset SX763

Al 09/05/2011 0:31, En/na Luca Olivetti ha escrit: It turns out that the ebu, in the gpio_led structure, uses gpio starting from 32, so defining "fake" leds using gpios 32-40 I could map all missing leds. Since they're active low, I used lq_register_gpio_ebu(0xff), so they all turn off as soon a

Re: [OpenWrt-Devel] Gigaset SX763

Al 08/05/11 18:45, En/na John Crispin ha escrit: >> Thank you for the detailed explanation. >> I have an LVC373A (octal latch), so it's probably EBU, isn't it? >> How do I try it? >> >> Bye > > > try this lq_register_gpio_ebu(XYZ); > > as the latch comes up in a undefined state, the values are

Re: [OpenWrt-Devel] Gigaset SX763

2011/5/8 John Crispin > if it was 29 on ifxmips/ it will be 29 on lantiq/. only the stp and ebu > gpios were mapped to new offsets. the first 32 gpios stayed the same. I tried 29 again now, and no power, also tried some others, nothing. If someone want's to see here is how power is set in origin

Re: [OpenWrt-Devel] Gigaset SX763

Al 08/05/11 20:16, En/na Andrej Vlašić ha escrit: > About that usb gpio. I already tried 29 and some others to xway_register_dwc > but it stays the same Disconnected port , and no power on it. Are you sure? I mean, I get the "DISCONNECTED PORT" message too if there's nothing connected to the usb

Re: [OpenWrt-Devel] Gigaset SX763

Hi All, I have one of these hanging around and not used for much. Happy to assist with testing, if I could get some instructions as to how the image is to be compiled (basic make menuconfig settings). Also on the photo here I can see TX and Rx only. I cannot see GND marked out. Any hints? Thannks

Re: [OpenWrt-Devel] Gigaset SX763

On 08/05/11 20:16, Andrej Vlašić wrote: Also this board doesn't have wlan eeprom, instead it is read by a wlan >> driver from a file inside fw. If someone has some answers on how to modify >> current ath5k driver, would like to know. >> >>> in a file inside the FS or in a sector on the flash ?

Re: [OpenWrt-Devel] Gigaset SX763

> >> Also this board doesn't have wlan eeprom, instead it is read by a wlan > driver from a file inside fw. If someone has some answers on how to modify > current ath5k driver, would like to know. > > > in a file inside the FS or in a sector on the flash ? > Inside a file, which has wlan mac addre

Re: [OpenWrt-Devel] Gigaset SX763

On 08/05/11 18:29, Luca Olivetti wrote: > Al 08/05/11 11:13, En/na John Crispin ha escrit: > >> EBU - external bus unit >> similar to STP but parallel. the xway has 4 x 16 bit ioport ranges that >> can be mapped to a special memory location. data written to that >> location is that physically writ

Re: [OpenWrt-Devel] Gigaset SX763

Al 08/05/11 11:13, En/na John Crispin ha escrit: > EBU - external bus unit > similar to STP but parallel. the xway has 4 x 16 bit ioport ranges that > can be mapped to a special memory location. data written to that > location is that physically written to the D0-15 lines on the memory > bus. in a

Re: [OpenWrt-Devel] Gigaset SX763

On 08/05/11 15:03, Luka Perkov wrote: > On Sun, May 08, 2011 at 12:37:51PM +0200, John Crispin wrote: >> on this pic -> http://wiki.openwrt.org/_media/toh/gigaset/dsc00453.jpg >> >> on the very top, right of where it says "PORTA SX76x" there is a small >> chip. can you tell us what is printed on it

Re: [OpenWrt-Devel] Gigaset SX763

On Sun, May 08, 2011 at 12:37:51PM +0200, John Crispin wrote: > on this pic -> http://wiki.openwrt.org/_media/toh/gigaset/dsc00453.jpg > > on the very top, right of where it says "PORTA SX76x" there is a small > chip. can you tell us what is printed on it ? HC595AG (inside of circle - ON) PAQ832

Re: [OpenWrt-Devel] Gigaset SX763

on this pic -> http://wiki.openwrt.org/_media/toh/gigaset/dsc00453.jpg on the very top, right of where it says "PORTA SX76x" there is a small chip. can you tell us what is printed on it ? ___ openwrt-devel mailing list openwrt-devel@lists.openwrt.org htt

Re: [OpenWrt-Devel] Gigaset SX763

On Sun, May 08, 2011 at 10:33:30AM +0200, John Crispin wrote: >>> I also looked up at those arcadyan board configs, and some of them have >>> _EBU addess and _USB pin defined. >>> I know that on this router usb power is on gpio 29( gpl source says that ) >> >> So you'll have to de

Re: [OpenWrt-Devel] Gigaset SX763

On 08/05/11 10:48, Luca Olivetti wrote: > Al 08/05/11 10:33, En/na John Crispin ha escrit: > >> >> if it was 29 on ifxmips/ it will be 29 on lantiq/. only the stp and ebu >> gpios were mapped to new offsets. the first 32 gpios stayed the same. > > Not related to the original question, but where I

Re: [OpenWrt-Devel] Gigaset SX763

Al 08/05/11 10:33, En/na John Crispin ha escrit: > > if it was 29 on ifxmips/ it will be 29 on lantiq/. only the stp and ebu > gpios were mapped to new offsets. the first 32 gpios stayed the same. Not related to the original question, but where I could find some documentation on stp/ebu, what th

Re: [OpenWrt-Devel] Gigaset SX763

Hi, >> I also looked up at those arcadyan board configs, and some of them have >> _EBU addess and _USB pin defined. >> I know that on this router usb power is on gpio 29( gpl source says that ) > > So you'll have to define it for your board in the call to xway_register_dwc > (ma

Re: [OpenWrt-Devel] Gigaset SX763

Al 07/05/11 23:23, En/na Andrej Vlašić ha escrit: > I also looked up at those arcadyan board configs, and some of them have > _EBU addess and _USB pin defined. > I know that on this router usb power is on gpio 29( gpl source says that ) So you'll have to define it for your board

[OpenWrt-Devel] Gigaset SX763

Hello! I'm trying to set up openwrt on this router, it is based on Lantiq Xway Danube Soc ( PSB50702 E), and manufactured by Sagem(previously by Siemens). Wiki page is here http://wiki.openwrt.org/toh/gigaset/sx76x I already managed to boot openwrt on it, but I cannot get USB working, because the