did you paint it right onto the glass where it goes into the frame Joe?
Outside I'm guessing not inside?
Wade
Oh Boy 33-2
Lake of the Woods
On Mon, Sep 28, 2020 at 8:08 AM Joe Della Barba wrote:
> My 47 year old original hatches will sometimes leak around the screws. I
> have been sealing them
These are available on Amazon. Ca for a few $. Just get the right diameter
Wade
Oh Boy C&C 33 MKII
On Mon, Oct 5, 2020, 3:53 PM Dean McNeill, wrote:
> I’m in Halifax, Nova Scotia, Canada if that’s not too far?
>
> The address is:
>
> DeanMcNeill
> 1963 Cambridge Street
> Halifax, NS
> Canada
> B
Two years ago i bought a new Nordac 3Di 135 furling genoa from North. It
was not cheap but it is fantastic. . Ive never sailed with a sail that
needs less tweaking which is awesome for single handing. Groove is wide and
predictable. Sent the measurements and perfect fit first time. My old
sail w
Hello,
I have a 1986 C&C 33 MK II. As well as the electric bilge pump I have the
usual Manual bilge pump in the cockpit. In addition, there is another
manual bilge pump in the cabin mounted under the Port side settee along the
forward bulkhead. This cabin bulge pump hose runs to the cockpit bil
Rather new to sailing Mike. I'm guessing that #1 means it's a light air
sail? Is it a 135?
Wade
On Tue, May 1, 2018, 07:24 Hoyt, Mike via CnC-List,
wrote:
> I just thought I would post this here because it may benefit somebody on
> the list rather than just post locally on kijiji
>
>
>
> Persis
t reach the forward edge of the mast. A 90%
> headsail would fall short of the mast. A 150% headsail would extend 50% of
> the way aft of the mast in relation to the foretriangle.
>
> I occasionally list a sail on eBay. I list the luff, foot, leech and LP
> dimensions.
>
> Den
an extra electric bilge pump which has since been
> removed.
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
> On Mon, Apr 30, 2018, 11:58 PM Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Hello,
>>
>> I have a
extra electric bilge pump which has since been
> removed.
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
> On Mon, Apr 30, 2018, 11:58 PM Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Hello,
>>
>> I have a
I think that's the answer Brad, thanks. Wade
On Tue, May 1, 2018, 20:58 Bradley Lumgair via CnC-List, <
cnc-list@cnc-list.com> wrote:
> My 2 manual bilge pumps both exit out their own thru-hull at the stern.
> The hoses are 1-1/2 inch coil reinforced.
> Brad
> Pulse C&C 33 Mk II
> Lake Huron
>
>
Thanks to everyone who responded to my confusion about the bilge pumps in
my C&C 33 MKII. I think I have an idea where to go from here.
Wade
Oh Boy
C&C 33 MKII
Kenora Ontario
On Wed, May 2, 2018, 15:01 Bradley Lumgair via CnC-List, <
cnc-list@cnc-list.com> wrote:
> I would think you’d want to in
with all due respect, this post has nothing to do with CNC, boating or
anything else we are discussing on this list
On Sun, May 27, 2018 at 4:36 AM, Erik Hillenmeyer via CnC-List <
cnc-list@cnc-list.com> wrote:
>
>
> http://service.curediabeteswithoutdrugs.com
>
>
>
> Erik Hillenmeyer
>
>
>
> ___
may I ask what you mean by linearize the instruments?
Wade
33 Mk II Oh Boy
On Sat, Jun 16, 2018 at 10:01 AM, ALAN BERGEN via CnC-List <
cnc-list@cnc-list.com> wrote:
> On the ST50/60/60+ instruments, there has to be 8 volts between the red
> wire and the screen. Less than 8 volts won't do. Th
I had to replace these on a C&C 30 Mk II a few years ago. It was a 1986 but
I believe C&C had the same tank manufacturer forever. The company name was
embossed faintly on the screw on port caps which I then used to Google
search and source new ones (which were very inexpensive by the way). If my
me
Are you making these Stu?
Wade
33 Mk II
Oh boy
On Jun 29, 2018 11:56, "Stu via CnC-List" wrote:
Is this what you had in mind for sling decals. These are approx. – 1” x
2.25”. Marine grade vinyl available in red, blue or black.
Haven’t figured out a shipped price yet. What would you pay for
Hi Josh,
Being relatively new to the sailboat business can I please ask what you
mean by "keeping the engine load as high as possible" with regard to Soot
accumulation?
Wade
Oh Boy C&C 33 MKII
On Sat, Jul 14, 2018, 16:24 Josh Muckley via CnC-List, <
cnc-list@cnc-list.com> wrote:
> I was pleasantl
ng the engine solely to charge the batteries.
>
> Bruce Whitmore
> 1994 C&C 37/40+ "Astralis"
> (847) 404-5092 (mobile)
> bwhitm...@sbcglobal.net
>
>
> ------
> *From:* Wade Glew via CnC-List
> *To:* cnc-list@cnc-list.com
>
t;C&C List"
>> Subject: Re: Stus-List Yanmar 3HM35F Exhaust riser/goose neck
>> Message-ID:
>>
>> Content-Type: text/plain; charset="utf-8"
>>
>> The Yanmar manual does have some guidance on page 44.
>>
>> https://drive.google.com/f
t Yanmar 3HM35F Exhaust riser/goose neck
>> Message-ID:
>>
>> Content-Type: text/plain; charset="utf-8"
>>
>> The Yanmar manual does have some guidance on page 44.
>>
>> https://drive.google.com/file/d/0B8pEh5lnvP1yenJtR1BxWjhqZGs/
>> view?usp=drivesdk
&g
I wish mine read 13 all the time!
Wade
Oh Boy 33
On Wed, Aug 29, 2018, 19:16 Edd Schillay via CnC-List, <
cnc-list@cnc-list.com> wrote:
> David,
>
> Not at all. If they were over 15V, then I’d worry. 13’s are perfect.
>
> All the best,
>
> Edd
>
> ---
> Edd M. Schi
Good Morning Chuck,
I would be interested in your instruments. Are you including the masthead
unit as well as thru hull transducers/flyweel?
Wade
Oh Boy 33
On Thu, Aug 30, 2018 at 7:55 AM Chuck Saur via CnC-List <
cnc-list@cnc-list.com> wrote:
> Happy Labor Day week! New boat (for me) and worki
is it correct to assume that the original fittings on my Kracor holding
tank will determine the size of vent hose I can use, or can I retrofit
larger hoses?
Would a second vent require a pro to create a fitting on my existing tank?
Wade
Oh Boy 33-2
On Sat, Sep 1, 2018 at 10:41 AM Howard and Ski
What make is the shaft seal and how difficult was the install Charlie?
Wade
Oh Boy C&C 33 MKII
On Sat, Oct 20, 2018, 06:36 Charlie Normand via CnC-List, <
cnc-list@cnc-list.com> wrote:
> Adrian
>
> Have had the shaft seal on Shadow Dancer for about 12 years now, never a
> problem, one of best up
would love to see a photo of your setup Andy
Wade
Oh Boy C&C 33 MK II
On Mon, Sep 23, 2019 at 3:05 PM Andrew Walther via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hi there,
>
> Not exactly what you're looking for but I laboured over the flexible /
> rigid panel installation and finally went wit
yeah this looks really good and out of the way altogether. Nice job Andy
Wade
On Mon, Sep 23, 2019 at 7:16 PM sv Rebecca Leah via CnC-List <
cnc-list@cnc-list.com> wrote:
> Andy,
> Your panel install looks great.
>
>
>
> Doug Mountjoy
> Sv Rebecca Leah
> C&C LF39
> 253-208-1412
> Port Orchard YC
Hi Everyone,
been following the folding prop thread with interest. I had a Michegan
Sailor 16 x 10 R fixed prop for 10 years. It was fine for all purposes
except sailing where it was like towing a drogue. I changed this year to a
FlexoFold 16 x 11 and my observations are these:
1. FlexoFold ha
Mine is a 2 blade Bruce
Wade
On Mon, Sep 23, 2019, 21:39 bwhitmore via CnC-List,
wrote:
> In each of the cases noted about Flex o Fold, are we talking about the 3
> blade or two blade models? The recommend a 3 blade for my 37/40 with a
> Yanmar 3JH2E.
>
> Looking forward to your thoughts,
>
> B
Hi Edd,
commendable task; here you go
Wade Glew - Oh Boy - C&C 33 MK II - 1986 - Sail no. 33011 -
wadeg...@gmail.com - Kenora Ontario, Canada.
and you don't have to feel bad for us up here; hockey season has started
and that's a great thing! Not to mention, when my hockey gear s
Hi Joe
Looking at the guage you've linked to, its obvious the "T" arms go in the
fuel line between the Racor and engine. Where does the threaded base of the
T go? What is a normal pressure? What pressure reading makes you decide to
change filters? Are the lined just clamped with small hose clamps
of vertical lift of diesel fuel would amount to 100
> inH2O, 3.5psia or 7 inHg.
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
>
>
> On Sun, May 24, 2020, 23:03 Wade Glew via CnC-List
> wrote:
>
>> Hi Joe
>> Looking at the guage you&#x
gt;
> *www.dellabarba.com <http://www.dellabarba.com>*
>
>
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Wade
> Glew via CnC-List
> *Sent:* Friday, May 29, 2020 9:52 AM
> *To:* cnc-list@cnc-list.com
> *Cc:* Wade Glew
> *Subject:* [EXTERNAL] Re:
Will Napa be able to tell me which Wix filter will fit my 2GMF Yanmar?
Wade
Oh Boy C&C 33 MKII
On Sat, Nov 3, 2018, 12:20 svrebeccaleah via CnC-List I second the vote for WIX available at your local NAPA store.
>
>
>
> Doug Mountjoy
> Sv Rebecca Leah
> LH39
> Port Orchard YC wa.
> ___
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
>
> On Sat, Nov 3, 2018, 1:27 PM Wade Glew via CnC-List
> wrote:
>
>> Will Napa be able to tell me which Wix filter will fit my 2GMF Yanmar?
>> Wade
>> Oh Boy C&C 33 MKII
>>
>
166 / Baldwin BF825
>
> sam
> C$C 26 Liquorice
> Ghost Lake Alberta
>
> On Nov 3, 2018, at 11:26 AM, Wade Glew via CnC-List
> wrote:
>
> Will Napa be able to tell me which Wix filter will fit my 2GMF Yanmar?
> Wade
> Oh Boy C&C 33 MKII
>
> On Sat, Nov 3,
May I please request some input and advice from list members re purchasing
a folding propeller?
I have a Yanmar 20GM20F with constant rating of 16 HP at 3400 RPM
Gear Ratio is 2, 62
current prop is Michegan sailor fixed blade 16 RH 10
On Contacting FlexoFold they have recommended: " a 2-blade 16
this looks good Josh though I fear the Alpine Butterfly knot would catch on
my baby stay the same way my continuous genoa sheet (secured to clew with
luggage tag knot) does now. I would love to remove the baby stay but I
can't find any information on rig stability if I were to do so. Any
opinions
Hi Rob,
are you speaking specifically of C&C 34's in this comment? My boat is a 33
MKII and I wonder if I might be able to do without my baby stay? I am 80%
cruiser, 20% racer on Lake of the Woods in Ontario so big seas are not
something I have to deal with. What would I sacrifice without the
is this a synthetic oil Josh?
Wade
Oh Boy C&C 33MKII
Lake of the Woods
On Wed, Nov 21, 2018 at 4:16 PM Josh Muckley via CnC-List <
cnc-list@cnc-list.com> wrote:
> I use Amsoil products for all my engines. The boat gets 15w40 heavy
> duty/marine diesel oil. It had a high TBN of 12. As the acid
the engine.
>
> Josh Muckley
> S/V Sea Hawk
> 1989 C&C 37+
> Solomons, MD
>
> On Thu, Nov 22, 2018, 6:11 PM Wade Glew via CnC-List <
> cnc-list@cnc-list.com wrote:
>
>> is this a synthetic oil Josh?
>>
>> Wade
>> Oh Boy C&C 33MKII
>
Is hdrochloric acid bad for the gel coat?
Wade
Oh Boy C&C 33 MKII
Lake of the Woods
On Mon, Dec 17, 2018, 12:10 dwight veinot via CnC-List <
cnc-list@cnc-list.com wrote:
> In salt water it comes from iron and manganese ions ever present same as
> you see at the watervlines in some toiler bowls th
How old is this Standard Horizon system John
Wade
Oh Boy C&C 33 MKII
Lake of the Woods
On Mon, Jan 7, 2019, 21:09 John and Maryann Read via CnC-List <
cnc-list@cnc-list.com wrote:
> Santa was very nice to me this year (many thanks Fred for all your help)
> so am selling our old system. Details a
Wow. Thanks Ken, Makes me wonder how I would perform in a circumstance
like this, and pray that I will never need to.
Wade
Oh Boy 33 MKII
Lake of the Woods
On Sun, Jan 27, 2019 at 6:05 AM Ken Heaton via CnC-List <
cnc-list@cnc-list.com> wrote:
> Good morning. Grab a coffee (or two), sit back,
What in the world does this have to do with a CNC sailboat list?
Wade
Oh Boy C&C 33
On Mon, Jan 28, 2019, 14:39 Allan Rheaume via CnC-List <
cnc-list@cnc-list.com wrote:
> http://credible.super-40.com
>
>
>
>
>
> Allan Rheaume
>
>
> ___
>
> Thanks every
Wouldn't the use of Spartite make it difficult at a later date to make any
fine adjustments of the the mast rake to change the center of
effort/weather helm?
Wade Glew
Oh Boy 33-2
Lake of the Woods
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_ca
I have not seen this on any of the four C&C 33 MKII in my harbour Brad.
These boats are all 1986/87 hulls
Wade
Oh Boy C&C 33 MKII
Lake of the Woods
On Tue, Feb 26, 2019, 10:36 Bradley Lumgair via CnC-List, <
cnc-list@cnc-list.com> wrote:
> Our 33-2 has a crack on either side of the cut-out seat a
Hi Listers,
some time ago there were some comments on the use of soft shackles to join
genoa sheets to the genoa clew. This idea sounds really interesting to me
but having browsed Amazon, I realize I don't know what working strength of
soft shackle I need to buy. My C&C is a 33 MK II with I dim
1989 C&C 37+
> Solomons, MD
>
>
>
>
> On Mon, Mar 4, 2019, 12:29 AM Wade Glew via CnC-List <
> cnc-list@cnc-list.com wrote:
>
>> Hi Listers,
>>
>> some time ago there were some comments on the use of soft shackles to
>> join genoa sheets to the gen
Sunny and hot here in Winnipeg!
Wade Glew
Oh Boy C&C 33 MKII
On Thu, Mar 14, 2019, 13:52 Randy Stafford via CnC-List, <
cnc-list@cnc-list.com> wrote:
> Yesterday in eastern Colorado we had a bomb cyclone, over land, at about
> 38 degrees north latitude. All-time records wer
My 33 Mk II is an 86 with single backstay
Wade
Oh Boy C&C 33 MKII
Lake of the Woods
On Sun, Apr 21, 2019, 21:31 Bradley Lumgair via CnC-List, <
cnc-list@cnc-list.com> wrote:
> Catching back up on the list.
> Do the '86 and '87 C&C 33s have a split backstay? Caught a reference to it
> in an old ar
a 1 gallon plastic ice cream bucket also works very well for winch
overhaul. Cut a smaller hole then an X in the bottom and push it over the
winch before you start. Another ice cream bucket is perfect for solvent to
clean the winch bearings, pauls etc so they can't get away in the process.
Placi
Hi Mike
I got a large knurled nut (external diameter equals the hub) from Edson.
It will still come loose with some vibration over a day but I can tighten
it way harder (and easier!) than with the previous smaller plastic hex
nut. Also easier to remove by hand. It's a pretty good look too! I al
Hey Dave, doesn't the dorade vent through the anchor locker make your
v-berth smell like wet / muddy anchor rode?
Wade
Oh Boy C&C 33 MKII
On Sun, Jul 28, 2019, 06:55 Dave S via CnC-List,
wrote:
> FYI and for the record.
>
>
>
> https://cncwindstar.blogspot.com/2019/07/33-2-ventilation-strategies
Hello listers, I would appreciate any advice you might have on my
electrical issue du jour.
Mine is a C&C 33 MK II and I have a Link 20 battery monitoring system.
Bank 1 (house) is 4 Trojan T-105 (225 AH) 6V deep cycles about 5 years
old. Bank 2 is a 12V starter battery dated 2005. I look afte
PM, Dennis C. via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
> Clean all the ground connections.
>
> Dennis C.
>
> On Tue, Aug 13, 2019 at 12:26 PM Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Hello listers, I would appreciate any advice you
gt;
> Joe
>
> Coquina
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Dave
> S via CnC-List
> *Sent:* Tuesday, August 13, 2019 3:38 PM
> *To:* Wade Glew
> *Cc:* Dave S ; cnc-list@cnc-list.com
> *Subject:* [EXTERNAL] Re: Stus-List Electrical
y affected by bad ground continuity.
>>
>> — Fred
>>
>> Fred Street -- Minneapolis
>> S/V Oceanis (1979 C&C Landfall 38) -- Bayfield, WI
>>
>> On Aug 13, 2019, at 12:39 PM, Dennis C. via CnC-List <
>> cnc-list@cnc-list.com> wrote:
>&g
.
>
> Dennis C.
> Touche' 35-1 #83
> Mandeville, LA
>
> On Tue, Aug 13, 2019 at 4:53 PM Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> Doesn't there have to be a grounding wire from the bus bar to the engine
>> anyways? Then all gro
one thing; but enough
>>> current to crank is another, and definitely something that will be
>>> adversely affected by bad ground continuity.
>>>
>>> — Fred
>>>
>>> Fred Street -- Minneapolis
>>> S/V Oceanis (1979 C&C Landfall 38) --
ltage is only part of the story. You're
> really looking for current. A corroded connection may show adequate
> voltage but may be incapable of passing enough current to start your engine.
>
> Dennis C.
> Touche' 35-1 #83
> Mandeville, LA
>
> On Tue, Aug 13, 2019
Can I ask Barry, is the barber hauler sheet on the Genoa Lew led to the
snap shackle from outside the lifelines or inside?
Wade
Oh Boy C&C 33 MKII
On Tue, Aug 20, 2019, 15:30 Barry Lenoble via CnC-List, <
cnc-list@cnc-list.com> wrote:
> Hey,
>
> Generally, the whisker pole is used if you are sai
good pic John; thanks. Is there a reason the twing line can't be attached
outside the lifeline?
Wade
Oh Boy, C&C 33 MK II
On Wed, Aug 21, 2019 at 11:09 AM Jim Watts via CnC-List <
cnc-list@cnc-list.com> wrote:
> I use a simple twing setup...easy to attach, easy to trim, cheap. Up to
> the point
>
> Jim Watts
> Paradigm Shift
> C&C 35 Mk III
> Victoria, BC
>
>
> On Wed, 21 Aug 2019 at 15:43, Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
>
>> good pic John; thanks. Is there a reason the twing line can't be
>> attached outside the
gt; Good luck with the troubleshooting.
> Can’t recall if I responded with this but some 33-2 electrical info and
> photos here
>
> http://cncwindstar.blogspot.com/p/blog-page.html?m=1
>
> Dave
>
> Sent from my iPhone
>
> On Aug 14, 2019, at 8:46 AM, Wade Glew wrote:
&g
I got this kit (included frames, mounting hardware and new plexi windows)
from Dan Boisvert @ fixleakyboats.com for my 33-2 in 2009. Since removal
of the old windows and installing the new ones was a skill I hoped to never
use again, and because I wanted someone to complain to besides myself if
t
Can I ask if I can use Shell Rotella Synthetic diesel oil in my 1986 Yanmar
2GM?
Wade
Oh Boy 33 MK II
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - u
, 2019, at 1:47 PM, Wade Glew via CnC-List <
> cnc-list@cnc-list.com> wrote:
> >
> > Can I ask if I can use Shell Rotella Synthetic diesel oil in my 1986
> Yanmar 2GM?
> >
> > Wade
> > Oh Boy 33 MK II
> >
7;t have to use Amsoil to use the analysis
> service. As I recall I haven't changed the oil in almost 3 years.
>
> Here is a copy of my last report.
> https://drive.google.com/file/d/1MaBnvf4Fc9auz-p_Yw-yp5uh-Z7R4N__/view?usp=drivesdk
>
> Josh Muckley
> S/V Sea Hawk
Yes, it's an entire binder with looseleaf pages from starting and breaking
in your engine to wiring diagrams, construction details, stuffing box
maintenance, tank (water, fuel, holding) sizes, line lengths/sizes and I
can't even remember what else. Are you looking for something in particular?
Wade
trying to remember Joe but I thought you said it was liquid electrical tape
you used on that hatch seal ?
Wade
Oh Boy, 33-2
On Sun, Aug 22, 2021 at 10:54 AM Joe Della Barba via CnC-List <
cnc-list@cnc-list.com> wrote:
> I got by with Capt. Tolley’s for many years, but recently my fo
Hi all,
On my 33-MK 2, I want to move the coach top winches about 12-18 inches from
their current location. The site I'm moving them to is a designated
location by design and the coach top is round and flat in the new location
to allow a winch placement. My question is, can I just fill the old
ckened epoxy. I go for about the consistency of ketchup. Without the
>> counter sink. It will crack over time.
>>
>> Doug
>>
>>
>>
>> Sent from my T-Mobile 4G LTE Device
>>
>>
>> Original message
>> From: Wade Glew vi
Sounds awful Dennis. Hang in there.
Wade
Oh Boy C&C 33 MKII
On Tue, Aug 31, 2021, 16:00 Dennis C. via CnC-List,
wrote:
> Update. Dock neighbor says Touche' is fine. The water is now 4-6 inches
> over the pier. The highest was 4.5 feet over the pier. Fortunately, there
> is no wave action
nice summary Riley; thanks
Wade
Oh Boy 33-2
On Wed, Sep 15, 2021 at 10:39 AM Riley Anderson via CnC-List <
cnc-list@cnc-list.com> wrote:
> Hi Joe and any others interested in this topic.
>
> I install lithium batteries as my side job and after installing lithium on
> our 38-ii and other large bo
very interesting stuff; thanks Chuck
Wade
Oh Boy 33-2
On Thu, Sep 16, 2021 at 3:23 PM CHARLES SCHEAFFER via CnC-List <
cnc-list@cnc-list.com> wrote:
> "Balsa core" gets some bad press and I was interested in how it came into
> boating, especially C&Cs.
>
> After some research, I learned:
> Makin
That's a lot of boat for 28k. Wish I lived in NS!
Wade
Oh Boy C&C 33 MKII
On Fri, Oct 8, 2021, 19:56 Adam Hayden via CnC-List,
wrote:
> Hey listers
>
> After some careful consideration we have decided to list State of Bliss
> for sale. We are going to follow Edd's plan and move to the dark sid
Are you saying the order is in and done Stu?
Wade
Oh boy 33-2
On Fri, Jan 14, 2022, 12:50 stu--- via CnC-List,
wrote:
> I think the PayPal problem has been resolved. Try Again.
>
> Stu
> Thanks to all of the subscribers that contributed to the list to help with
> the costs involved. If you want
I did not see a link to the order form or payment platform. Is it too late
to order 10x14 with Oh Boy name?
Wade
Oh Boy 33-2
On Fri, Jan 14, 2022, 12:50 stu--- via CnC-List,
wrote:
> I think the PayPal problem has been resolved. Try Again.
>
> Stu
> Thanks to all of the subscribers that contribu
There is nothing wrong with using food grade mineral oil, available in Wal
Mart pharmacy isle for under $5.
Wade
Oh boy 33-2
On Sun, Feb 20, 2022, 20:13 Robert Abbott via CnC-List, <
cnc-list@cnc-list.com> wrote:
>
> Charlie
>
> Beeswax can sometimes be found at some big box stores, hardware sto
Does anyone put Sea Foam in their Diesel fuel?
Wade Glew
Oh Boy, 33 MK II
Lake of the Woods
What "control panel" are you referring to? Ignition, oil/fuel gauges etc?
Wade
Oh boy 33 mk II
Lake of the Woods
On Thu, Jul 7, 2022, 08:48 Jeff Nelson via CnC-List,
wrote:
> It's not for the starter...It is for power to the control panel. It just
> happens to be behind the starter on top of
Has anyone figured out how to mount a flexible solar panel on the bimini
top without the panel edges/corners chafing the sunbrella?
Wade
Oh Boy, C&C 33 mk II
Lake of the Woods
ini using rare-earth-magnet. Seen over
> 40 knots without any issues.
> https://suntechsolar.ca/product/rare-earth-magnet-mounting-kit/
>
> *Kevin Wright*
> Landfall 43
> Raven
> Midland ON
>
>>
>>
>> On Tue, Jul 26, 2022, 8:22 PM Wade Glew via CnC-List &
Leather is costly. I rewrapped the top half of my wheel with bike handle
bar wrap. Creates a nice soft and warm feel. Weathers well and costs $20.
Infinite colour choices. Easy to apply/remove. I picked one that looks like
cork. It seems to last about 2-3 years
Wade
Oh Boy 33-2
On Sun., Nov. 27, 2
that is a beautiful boat Dave. If you can't get your asking price for a
boat that loved, there is no justice in the world
Wade
Oh Boy 33-2
Lake of the Woods
On Sun, Jul 23, 2023 at 7:22 PM Dave S via CnC-List
wrote:
> Good evening all,
> As I am now the owner of two boats, I am reluctantly offe
Dear Listers,
As many of you know, the 33 MK II has a single rod backstay which
terminates approximately in the centre of the reverse transom. I don't
have a hydraulic backstay tensioner. Instead there is a small (perhaps 6")
diameter wheel in the backstay which can be turned by hand (rather
la
me there is a better
way ...
Wade Glew
Oh Boy C&C 33 MK II
On Sun, Sep 6, 2020 at 9:45 PM Len Mitchell via CnC-List <
cnc-list@cnc-list.com> wrote:
> Nate, I installed a drain last year. I used magnets too and drilled from
> outside. I also used a door drill kit and a dru
not that I disagree with you in any way Andrew but, regardless of regatta
or class of boat or year of competition, the 7th race between Alinghi and
New Zealand in 2007 is an all time highlight reel that will be played
forever.and never surpassed so matter what boats we choose to race.
merry christ
Merry Christamas to you too Stu and Gladys,
I don't contribute much to this group but I seriously enjoy the sharing of
knowledge, the humour, and the reminder that life is not technology; it's
the people we know and the friendships we cultivate. Thank you very much
for supporting that in our C&C
Besides, arent you sailing in fresh water?
Wade
Oh Boy C&C 33 MKII
Lake of the Woods
On Tue, Jan 19, 2021, 14:48 Michael Crombie via CnC-List, <
cnc-list@cnc-list.com> wrote:
> But in my case the water is actually seeping in through the bilge wall not
> running down into the bilge
>
> On Tue, Jan
my 135 roller furler is a 3DI (Nordac) and I think it's brilliant. Great
shape, great fit first time (which I would like to attribute to my
measuring 5 times).
It's 3 years old and looks like new. I'm careful not to abuse my sails
though I do sail single handed a lot so it sometimes takes a bea
Mine is dry. So far.
Wade Glew
Oh Boy C&C 33 MKII
Lake of the Woods
On Wed, Mar 3, 2021, 18:31 Sam Salter via CnC-List,
wrote:
> Flexofold folding 2 blade prop.
> Do you lube it or leave it dry?
> I’ve been leaving it dry but I’m open to suggestions/experience 🤷🏼♂️
>
This is a terrific documentation of your project Mike. I hope I never have
to use it! I hate being in that hole and I would have to cut out one of my
Propane lockers to do it. Kids are now old enough to know they don't have
to go down there just because I tell them to anymore 🙁
Wade
Oh Boy C&C 33
In ordering size, any info re fit? I'm 5'9", 155 lb and thinking Medium.
Make sense?
Wade
Oh Boy
33 mk 2
On Thu, Feb 29, 2024, 05:19 Motion Designs Limited via CnC-List <
cnc-list@cnc-list.com> wrote:
> The classic C&C Rugby shirts have arrived.
>
> Limited Stock available, not sure if I’ll do a
Sorry, didn't see size chart. Got it
W
On Thu, Feb 29, 2024, 05:19 Motion Designs Limited via CnC-List <
cnc-list@cnc-list.com> wrote:
> The classic C&C Rugby shirts have arrived.
>
> Limited Stock available, not sure if I’ll do another run so get yours
> while they are available.
>
> To all thos
Hi everyone, I wonder if anyone might be able to direct me to a resource
with instructions to fill drilled holes in my coachtop?
I moved a winch and a sheet stopper to new locations. The holes that were
left are in an area that is non-skid. I filled the holes almost to the top
with thickened Wes
Hi Chuck
I would really appreciate a copy of your article re window replacement with
VHB and Dow
Wade
Landfall 39
Your contributions help pay the fees associated with this list and help to keep
it active. Please help by making a small contribution using PayPal at:
https://www.paypal.com/paypalm
Looks great! Nice job!
Wade
39 Landfall
LOTW
On Thu, Jul 10, 2025, 10:12 Dennis C. via CnC-List
wrote:
> When I had my marine repair business (paid hobby, basically), I did a teak
> hatch deck replacement job on a Grand Banks trawler. I worked with the
> Plasdeck folks. Nice to work with. I
96 matches
Mail list logo
