Stus-List Re: Hand rail replacement- sources

Peter, on our 33-ll I took the old ones off and had a local boat builder, Bruckmann, make new ones that I varnished at home. I would think a good cabinetmaker could do it too. Get Outlook for iOS From: Peter W. via CnC-List Sent: Wednesday

Stus-List Re: Recommendations to rebuild hydraulic cylinders for backstay

I always bring mine home, think the extreme cold and dry weather when combined with the lack of use are bad for the seals. Get Outlook for iOS From: paul.hood via CnC-List Sent: Friday, November 17, 2023 6:48:48 PM To: David Risch via CnC-L

cnc-list@cnc-list.com

Or foredeck cows if you have bee, on the list long enough Get Outlook for iOS From: David Risch via CnC-List Sent: Thursday, September 14, 2023 6:10:39 PM To: Stus-List Cc: David Risch Subject: Stus-List Re: Winch Size for C&C34 Wow…much

Stus-List Re: 33-2 Spinnaker Track on Mast

Bottom of this page http://hollandmarine.com/hmp-flipbook-2022/flipbook/index.html?page=312 is what's on my 33-11 I believe.Still asleep for the winter so I can't check yet. Sout shore yachts may have as well. Paul From: andrew--- via CnC-List Sent: Saturday, A

Stus-List Re: C&C 35 Mk I Recommendations for Sailmaker

I ve used Sportech Sails in St Catherine’s for sails and canvas work for a while now. Been very happy with Jamie’s work Paul From: Glen Eddie via CnC-List Sent: Thursday, January 5, 2023 10:28:13 AM To: Stus-List Cc: Glen Eddie Subject: Stus-List C&C 35 Mk I Re

Stus-List Re: Hatch in head

Jim, We’re yours A&H or Bomar? Our 33-11 had bomar’s that I replaced with Lewmar years ago … fit the moulded openings better than the originals. Paul From: Jim Watts via CnC-List Sent: Saturday, December 10, 2022 7:50:58 PM To: Stus-List Cc: Jim Watts Subject

Stus-List Re: Vang repair

I've used RivNuts on our vang after having issued with helicoils not having enough material to get a good hold in. I did buy the tool which made it a simple installation. -Original Message- From: Jeff Nelson via CnC-List Sent: October 31, 2022 10:43 AM To: cnc-list@cnc-list.com Cc: Jef

Stus-List Re: 33-2 hatch screws?

On our 33-ll they go into the fibreglass lip around the hatches. We replaced the bomar hatches with Lewmar ocean series hatches that turned out to match the openings better. When we were doing this we found some cracks in the liner/ deck moles join which we filled with gflex. Paul ___

Stus-List Re: Mast head antenna cable

Charlie, better to terminate both ends with a pl259 connector and use a pl258 female to female connector to join them. Coax doesn’t splice well. Shakespeare have a gold plated solderless connector that I’ve had good success with, that provides a minimal loss. Paul _

Stus-List Re: Source for sheaves

Did the same with our mast head sheaves, new ones are ball bearing, and really helped reduce the friction in our halyards. Paul From: Bob Mann via CnC-List Sent: Tuesday, November 9, 2021 3:06:43 PM To: Stus-List Cc: Rod Stright ; Bob Mann Subject: Stus-List Re

Stus-List Re: Racer diesel filter assemblies

a.m., Paul Fountain via CnC-List wrote: We put a Racor 500 on Perception, located under the sink for easy access, replaces a spin on which was nothing but issues changing the filters and priming. We had a lot of ‘stuff’ in the diesel fuel when we bought Perception, and went thru a lot of filters in

Stus-List Re: Racer diesel filter assemblies

We put a Racor 500 on Perception, located under the sink for easy access, replaces a spin on which was nothing but issues changing the filters and priming. We had a lot of ‘stuff’ in the diesel fuel when we bought Perception, and went thru a lot of filters in the early days. Paul Fountain Perce

Stus-List Re: leeward layline

On one boat I was the union member, I finally put the helmsman on foredeck after one too many snap jibes ….. after that they were much more controlled, from the foredeck! Paul From: Graham Collins via CnC-List Sent: Wednesday, October 6, 2021 5:56:01 PM To: St

Stus-List Re: Mast in and out

A friend got quoted about that for unstepping, storing for the winter and restepping in the spring in Hamilton. He has a 36’ Elite with a deck stepped mast. He had to strip the mast once unstepped, and prep it in the spring. Paul From: Jim Watts via CnC-List Se

Stus-List Re: Insurance

We are with Skippers plan (Aviva) and have been for years. They covered us for the first 2 years while we were living in the US, and no issues when we returned to Canada. I deal with Drew Robertson, let me know if you need more info. Paul From: Doug Robinson via

Stus-List Re: Bow Repair

Take the damaged ones to a local fabrication shop, they should be able to make you new ones. Paul From: Brian Morrison via CnC-List Sent: Saturday, September 25, 2021 8:44:50 AM To: Stus-List Cc: Brian Morrison Subject: Stus-List Bow Repair Hello All, I had a

Stus-List Re: Boat trucking recommendations

We had good success with Andrews moving a 27 to the states when we moved there, and a 33 back to Canada. Both ways we got a back haul rate, when they have a truck moving empty to fetch a boat or return from a delivery. The return to Canada also was 2 up as they had a slightly smaller boat to bri

Stus-List Re: UFO NOISE

Jim, I think this may be a hearing issue 😁 Paul From: Jim Watts via CnC-List Sent: Thursday, May 20, 2021 12:41:56 PM To: Stus-List Cc: Jim Watts Subject: Stus-List Re: UFO NOISE I have the same issue, I "fix" it by Velcro lashing an extended boathook up the p

Stus-List Re: 35mk2 3.5" masthead sheaves

Did the same on our 33-2 Paul From: Bob Mann via CnC-List Sent: Thursday, April 15, 2021 4:20:17 PM To: Stus-List Cc: Bob Mann Subject: Stus-List Re: 35mk2 3.5" masthead sheaves For my 35 mk I I got them replaced by Garhauer. Bob On 04/15/2021 4:11 PM Shawn Wr

Stus-List Re: Atomic 4 trouble shootings

And condenser ... Almost forgot Paul From: dwight veinot via CnC-List Sent: Sunday, April 11, 2021 7:05:41 PM To: Stus-List Cc: dwight veinot Subject: Stus-List Re: Atomic 4 trouble shootings Check the points and make sure the gap is set right On Sun, Apr 11,

Stus-List Re: Atomic 4 trouble shootings

>From my A4 days ( 20 years ago) Check your points and cap . . . Then coil . . >If you don’t an have electronic ignition. Paul From: Joel Delamirande via CnC-List Sent: Sunday, April 11, 2021 2:35:48 PM To: Stus-List Cc: Joel Delamirande Subject: Stus-List A

Stus-List Re: Rudder post bearing for 33ii

Is this the delrin ring around the top of the rudder post ? When ours gave up (split) I got one from SouthShore that was a good fit, had to get the pin also as the old one was bent before we bought Perception. Going to be time for another soon I am sure ... so interested in what you find. -

Stus-List Re: Mast Base Blocks

Same on our 33-2 Paul From: David Knecht via CnC-List Sent: Friday, March 19, 2021 9:17:44 AM To: CnC CnC discussion list Cc: David Knecht Subject: Stus-List Re: Mast Base Blocks I also have all Garhauer, but on shackles attached to the perforated /collar base

Stus-List Re: Precision Sails

Lots of sailmakers in the Toronto area – UK, Doyle, North are the big ones, and a number of small ones! And had a Haarstick genoa on our 27 great sail, cut at their Rochester loft. Assembles at their Hamilton Ontario affiliate (now Bay Sails) From: Della Barba, Joe via CnC-List Sent: March 16,

Stus-List Re: midship cleats on aluminum rail?

We have had the Johnson toe rail cleats on our 33-ll, work for 10+ years worked great for us. My sister has them on her 30 as well. Like that they fold when not needed. And lines are clear of the deck no tripping hazard going forward, especially with he grandkids on board, they don’t alway

Stus-List Re: C&C 34 re-power HP

WE put a 25 hp Beta in our 33-II when we did her – been great lots of power. Also went with a Flex-o-fold 2 blade prop, if I needed more push id upgrade the prop to a 3 blade flex-o-fold. From: Jeremy Ralph via CnC-List Sent: February 16, 2021 2:08 PM To: cnc-list@cnc-list.com Cc: Jeremy Ralph

Stus-List Re: masthead sheave thoughts?

Our 33-ll the top lifts off . . . Paul From: Adam Hayden via CnC-List Sent: Saturday, January 30, 2021 5:30:26 PM To: Stus-List Cc: Adam Hayden Subject: Stus-List Re: masthead sheave thoughts? This is a timely post. How do you access the sheaves at the top of

Stus-List Re: masthead sheave thoughts?

Dave, We had garhauer make new sheaves for Perception. The 2 aft ones were fine with their stock offerings, the 3 forward were a tad narrower, and I ended up sending them one of our old ones to replicate the sizing. The old ones had razor sharp edges from rubbing the mast head casting. Great up

Stus-List Re: C&C Rendezvous at Maritime Museum in Kingston?

Great idea, Kingston is a great location, 3 major airports in easy drive Toronto, Ottawa and Montreal, good waterfront hotels and marinas lots of C& C’ s still on the lake(Ontario). Paul From: Dennis C. via CnC-List Sent: Friday, January 8, 2021 8:19:55

Re: Stus-List Yanmar cutting out at sea?

common if engine was gas. Did your Yanmar replace a gas engine? John and Maryann Legacy III 1982 C&C 34 Noank, CT From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Paul Fountain via CnC-List Sent: Saturday, September 05, 2020 4:20 PM To: cnc-list@cnc-list.com Cc:

Re: Stus-List Yanmar cutting out at sea?

I’d also pull the fuel pick tube and see if there is a screen in the end of it, if there is one remove it - it’s likely picking up sediment and starving the engine, dropping ir when the engine stops. If it that or the filters I would either polish the fuel, and add a cleaner, or remove it and h

Re: Stus-List Sealing a plumbing leak on the head outlet

Use liquid disk soap to lure both the barb and inside of the hose, heat first as suggested. I find it easier to remove the barb from the head to get the hose on on the Jabsco toilets. Paul From: CnC-List on behalf of Ian Matthew via CnC-List Sent: Sunday, Augu

Re: Stus-List Water Collecting Along Toe Rail

We followed Dennis’ suggestion of the lamp wick, works great. Paul From: CnC-List on behalf of Dennis C. via CnC-List Sent: Saturday, August 15, 2020 12:27:43 PM To: CnClist Cc: Dennis C. Subject: Re: Stus-List Water Collecting Along Toe Rail This has been di

Re: Stus-List Stuck screw

I’ll second this - I’d try to lift the track, be sure there is room for some butyl tale around 5he bolt holes, using a counter sink if not and rebed them. Or try the sealer, multiple applications over a few days. Paul From: CnC-List on behalf of Tom Buscaglia v

Re: Stus-List C&C 33 MK II backstay

The 33-LLP was one o& 5he first C&C’s to use a frame carrying the loads, stays, keel, engine, and a skin for the hull - Rob Ball may correct me on this! So I would think it would take some engineering to create strong enough attachment points for your changes. I would be looking at lubricating

Re: Stus-List Sunglasses favorites

I won’t use polarized lenses, a hold over from my flying days, bot do keep a pair on board when south for reef spotting. Paul From: CnC-List on behalf of David Knecht via CnC-List Sent: Sunday, August 9, 2020 6:11:14 PM To: CnC CnC discussion list Cc: David K

Re: Stus-List Sunglasses favorites

Love my ray bans, especially after cataract surgery in both eyes with correcting lenses . Paul From: CnC-List on behalf of Dennis C. via CnC-List Sent: Sunday, August 9, 2020 5:03:30 PM To: CnClist Cc: Dennis C. Subject: Stus-List Sunglasses favorites Af

Re: Stus-List Listers Age Range

l it nice to see there other members in Ontario We can sailing or race but I’m not there yet We can meet if you want too Is it true that port credit has the best sailing school in the area On Thu, Jul 16, 2020 at 11:53 AM Paul Fountain via CnC-List mailto:cnc-list@cnc-list.com>> wrote: 68, be

Re: Stus-List Listers Age Range

68, been sailing since 12, member of PCYC since 1972! Perception is our 2nd C&C owned her for 20 years now, had a 1977 C&C 27 MK 3 for 10 years before that. Somewhere there is a picture of my dad’s C&C 25,our C&C 27, and my sisters C&C 30 (she still has it) at PCYC! Paul Fountain Perception I

Re: Stus-List Listers Age Range

Dan, Where in Grenada? We love it there, usually for Christmas. This year we are still trying to sort out! Have friends at Coyaba and Johanna at Sunsation tours! Paul From: CnC-List on behalf of Daniel Cormier via CnC-List Sent: Wednesday, July 15, 2020 1:10:

Re: Stus-List VHF Radio with Outside Extension Mic

I also like my ICOM 506 with AIS receive and ram mike. I have a hand held, but like the higher power, and higher antenna the ICOM gives me. Paul From: CnC-List on behalf of ALAN BERGEN via CnC-List Sent: Monday, July 6, 2020 2:50:25 PM To: C&C Cc: ALAN BERGEN

Re: Stus-List Shift lever

https://edsonmarine.com/products/pedestals-cockpit-accessories/engine-controls-accessories/replacement-engine-control-handles/ Put these on our 85 33-ll. Paul From: CnC-List on behalf of John and Maryann Read via CnC-List Sent: Monday, July 6, 2020 7:21:27 AM T

Re: Stus-List Rudder and cutlass bearing

and cutlass bearing Do u have a phone number? On Fri, Jun 5, 2020 at 8:52 AM Paul Fountain via CnC-List mailto:cnc-list@cnc-list.com>> wrote: Talk to Roy Singh Roy’s Marine Service, he’s mostly at PCYC. He has a tool to press out the bearing without removing the shaft, and press the new

Re: Stus-List Rudder and cutlass bearing

Talk to Roy Singh Roy’s Marine Service, he’s mostly at PCYC. He has a tool to press out the bearing without removing the shaft, and press the new one in. Paul From: CnC-List on behalf of Joel Delamirande via CnC-List Sent: Thursday, June 4, 2020 11:54:07 AM To:

Re: Stus-List Loong Sails

Made in China, personally, I am trying to avoid made in China products when there are made in North America, Europe or Australia/New Zealand alternatives, even at an additional cost. Paul From: CnC-List on behalf of DANIEL WATTS via CnC-List Sent: Thursday, Ju

Re: Stus-List Coupler removal to install Dripless Shaft Seal

John, Done this twice, and it’s getting done now, the first time, used a socket aligned with the prop shaft and bought some Grade8 bolts long enough to go then the coupling halves, and kept evenly tightening them to press the shaft out ... every time the set screw hole got to the top we added p

Re: Stus-List Fuel Transfer Pump

Same for us, best part is with the portable tank on the cockpit floor you never over fill. I use a universal fuel line with a bulb to start . works great! Paul From: CnC-List on behalf of Charlie Nelson via CnC-List Sent: Saturday, May 16, 2020 5:23:01 PM T

Re: Stus-List 34-36R Deck Repair Project

I’ve had success with electrical tape Paul From: CnC-List on behalf of Ronald B. Frerker via CnC-List Sent: Thursday, May 7, 2020 1:28:26 AM To: cnc-list@cnc-list.com Cc: Ronald B. Frerker Subject: Re: Stus-List 34-36R Deck Repair Project What kind of ta

Re: Stus-List Need to replace forward hatch on 35 mkIII

tain via CnC-List mailto:cnc-list@cnc-list.com>> wrote: Our 77 C&C27-3 had an Aitkens&Hoyle hatch, much better than the Bomar hatches on our 85 33-ll, which have been replaced with Lewmar Ocean series hatches. The angle of the forward hatch made the low profile hatches impractica

Re: Stus-List Need to replace forward hatch on 35 mkIII

Our 77 C&C27-3 had an Aitkens&Hoyle hatch, much better than the Bomar hatches on our 85 33-ll, which have been replaced with Lewmar Ocean series hatches. The angle of the forward hatch made the low profile hatches impractical, and the raised Fiberglas either side made them unattractive. I’d rat

cnc-list@cnc-list.com

PCYC is on Lake Ontario, and fortunately have floating docks, so had minimal effect on us. It did get to with in a couple of inches of our main power feed having to be turned off – so this winter we will be relocating it to higher ground. The biggest impact was the limited number of places our m

Re: Stus-List Another Fuel Mystery

Check your fuel feed line, I have had the inner liner collapse and starve the engine of fuel then once the engine shuts down and the suction released start and run fine for a bit. This was on a Atomic 4 boat. Had a similar thing on our dinghy last season. Paul F

Re: Stus-List C&C Regatta on Lake Ontario

I would guess if its Lake Ontario it would be the Greater Toronto Area, perhaps Rochester , it would be great if it could be at Niagara-On-The-Lake original home of one the original C&C plants (Hinterhoeller’s), however they have limited visitor space and are a busy club. If there is interest

Re: Stus-List Raymarine to octopus drive upgrade - UPDATE

Dave, Interested why you feel the current unit needs to be replaced. We put the ray system you have on Perception our 33-ll 3 years ago when we upgraded our electronics so far it’s performed as well as the Navico wheel pilot it replaced, and as Dennis has said they work well! With our short sea

Re: Stus-List Folding & Feathering Prop Recommendations

Bruce, We put a flex-o-fold 2 blade on our 33-ll after repowering her better reverse, and power in forward. l seldom try WOT, as I have plenty of speed at 2700 rpm. 9 or 10 years later no issues. Paul From: CnC-List on behalf of Bruce Whitmore via CnC-List Se

Re: Stus-List 33-2 portlight material

Dave, when we did Perception for the second time we used 3/8 cast polycarbonate. I had Rob at south shore make them for me as the previous replacement damaged the frames and had used 1/4" extruded poly, which had cracked, and he had the original templates. We had them installed and the frames r

Re: Stus-List 33-2 Interior upholstery yardage?

Dave, We had the company that has done our living room do ours, gave him all the cushions, and he told us how much he needed. Bought it at one of the discount fabric stores in Hamilton. Paul From: CnC-List on behalf of Dave S via CnC-List Sent: Wednesday,

Re: Stus-List 33 mkii Flare stowage box and bracket project.

No they are not illegal, I fact most boats have them. Paul From: CnC-List on behalf of Bill Coleman via CnC-List Sent: Monday, July 29, 2019 4:42:50 PM To: cnc-list@cnc-list.com Cc: Bill Coleman Subject: Re: Stus-List 33 mkii Flare stowage box and bracket proj

Re: Stus-List 1985 CNC 33-2 Pedestal Throttle handle

Replaced both on our 33-2 with Edson stainless many years ago still work great. -Original Message- From: CnC-List On Behalf Of Ray Macklin via CnC-List Sent: July 12, 2019 8:20 PM To: cnc-list@cnc-list.com Cc: Ray Macklin Subject: Stus-List 1985 CNC 33-2 Pedestal Throttle handle I brok

Re: Stus-List test

two -Original Message- From: CnC-List On Behalf Of Della Barba, Joe via CnC-List Sent: July 2, 2019 9:55 AM To: 'cnc-list@cnc-list.com' Cc: Della Barba, Joe Subject: Stus-List test one ___ Thanks everyone for supporting this list with yo

Re: Stus-List Rigid Boom Vang?

When I replaced the hatches on our 33-II I reversed the mid ship hatch …. Improves the ventilation when in our slip! From: CnC-List On Behalf Of Rick Brass via CnC-List Sent: June 27, 2019 9:08 AM To: cnc-list@cnc-list.com Cc: Rick Brass Subject: Re: Stus-List Rigid Boom Vang? Ditto the A&H h

Re: Stus-List Rigid Boom Vang?

Garhauer From: CnC-List On Behalf Of Edd Schillay via CnC-List Sent: June 25, 2019 11:30 AM To: cnc-list@cnc-list.com Cc: Edd Schillay Subject: Stus-List Rigid Boom Vang? Listers, My rigid boom vang has seen better days and I’m looking to do a replacement. Can anyone recommend a good option

Re: Stus-List Fuel filter maintenance stories

Or an oil extractor? From: CnC-List On Behalf Of ALAN BERGEN via CnC-List Sent: May 29, 2019 6:13 PM To: C&C Cc: ALAN BERGEN Subject: Re: Stus-List Fuel filter maintenance stories Will a Shop Vac work? On Wed, May 29, 2019 at 8:59 AM Charlie Nelson via CnC-List mailto:cnc-list@cnc-list.com>

Re: Stus-List Prop strut

Try Buck Algonquin: https://catalog.hydrasearchrecreational.com/category/struts-1 From: CnC-List On Behalf Of Gerald Fennessey via CnC-List Sent: May 28, 2019 9:27 AM To: cnc-list@cnc-list.com Cc: Gerald Fennessey Subject: Stus-List Prop strut Hi I have a 1985 C&C 35 MK 3 with a very bent pr

Re: Stus-List Source for replacement lifelines in Toronto? Now general lifeline information

World Sailings Offshore special regs require Stainless steel on all mono hull sailboats except for ‘Short races, close to shore in relatively warm or protected waters normally held in daylight.’Covered in Offshore Special Regulations. Our club uses these regs for all long distance races on L

Re: Stus-List Source for replacement lifelines in Toronto?

Klacko in Oakville - send them your old ones and have them make new ones. When we did ours we eliminated the covering (which is now the offshore rule), which eliminated the rusting. -Original Message- From: CnC-List On Behalf Of Dave via CnC-List Sent: May 12, 2019 8:10 PM To: C&c Stus

Re: Stus-List Source for bronze

Try South Shore – I have sourced the derlin ring that the rudder of our 33-II slides on there. From: CnC-List On Behalf Of Matthew L. Wolford via CnC-List Sent: April 20, 2019 10:11 AM To: cnc-list@cnc-list.com Cc: Matthew L. Wolford Subject: Stus-List Source for bronze Listers: I am in

Re: Stus-List 33-2 Transom cracks

Our 33-11 also has these cracks, and has since we’ve owned her, 19 years. They do appear to be cosmetic and the gel coat has worn away there though I’ve never figured out what did that. I may try to fill them this year and see what happens. From: CnC-List On Behalf Of Wade Glew via CnC-List

Re: Stus-List Dirty fuel?

Don, Had this issue on our 33, culprit was bottom crud getting stirred up and plugging the screen on the fuel pickup. We polished the fuel a couple of times and the issue would still occur occasionally - solution was to remove the screen on the fuel pickup, I actually replaced the pickup tube.

Re: Stus-List Shrink-Wrapping Painted Boats

Randy here in Southern Ontario, gel coated boats usually shrink wrap to the waterline, but painted or awl gripped boats to the shear line. -Original Message- From: CnC-List On Behalf Of Randy Stafford via CnC-List Sent: Saturday, November 3, 2018 3:52 PM To: cnc-list Cc: Randy Staffo

Re: Stus-List Filling diesel tank

I've used a siphon hose, no holding or tipping, and if you set it up so the 5 gallon is on the cockpit floor it will not over fill! From: CnC-List On Behalf Of David Knecht via CnC-List Sent: Thursday, October 25, 2018 10:17 AM To: CnC CnC discussion list Cc: David Knecht Subject: Stus-List

Re: Stus-List Rob - C&C long time question

We’ve had Perception C&C 33-II for 18 years now more to come! Had a C&C 27-III for 10 years before that. Only looked at C&C’s when we were moving up ….. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jack Fitzgerald via CnC-List Sent: Thursday, September 27, 2018 8:51 AM To:

Re: Stus-List Rob - C&C long time question

We’ve had Perception C&C 33-II for 18 years now more to come! From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jack Fitzgerald via CnC-List Sent: Thursday, September 27, 2018 8:51 AM To: C&CList Cc: Jack Fitzgerald Subject: Re: Stus-List Rob - C&C long time question Hello Al,

Re: Stus-List Structural glass work

Think it’s because the link is to amazon.ca not amazon.com. Paul From: 30031472000n behalf of Sent: Tuesday, July 24, 2018 11:07 AM To: cnc-list@cnc-list.com Cc: bushma...@aol.com Subject: Re: Stus-List Structural glass work OK this is weird: I tried to order t

Re: Stus-List how to search the archives and marine insurance

Jeff, Check with Andrew Robertson at Skippers Plan, if they require an out of the water survey – or if they will accept one done afloat. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jeff Bechtel via CnC-List Sent: Tuesday, June 19, 2018 10:00 AM To: cnc-list@cnc-list.com

Re: Stus-List Toe Rail Tie off

We have a pair of foldable cleats on our 33-ll and the have worked well for us, and we need them for our slip. To me the hull deck join is one of the stronger sections of the board, and most of the load is almost parallel to the hull. We’ve had no issues in 10+ years of use, and my sister has th

Re: Stus-List Anyone Have A Stack Pack?

We have one from Sportech in St Catherines, and love it. Its one of the first they did. Jamie has done a number of improvements over the years since then and we have added some - pictures once the boat is put together, she splashed yesterday! Paul Fountain Perception II 1985 C&C 33-II k/cb Port

Re: Stus-List Gooseneck toggle

Check with Rob at SOUTHSHORE yachts in Virgil ( Niagara on the lake) he may have one or know where to find. Paul From: CnC-List on behalf of Derek McLeod via CnC-List Sent: Friday, May 4, 2018 1:38:55 PM To: CnClist Cc: Derek McLeod Subject: Stus-List Gooseneck

Re: Stus-List Raymarine Wind

Somewhere on raymarines site are the voltages to check the wind transducer. Also check the connections especially the ground. Paul From: CnC-List on behalf of ALAN BERGEN via CnC-List Sent: Wednesday, April 25, 2018 6:16:08 PM To: C&C Cc: ALAN BERGEN Subject: S

Re: Stus-List Dodger and Bimini Configuration Question

Steve, Here are some pictures of my sisters 30 with a dodger and Bimini. They also have a connector panel. http://www.sportechsails.com/index.php?p=Gallery&l=C&gallery=cc-30-mki-dodger-bimini From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Steven A. Demore via CnC-List Sent:

Re: Stus-List Traveler fit

I’ll also recommend Garhauer, put one on our 33-2 and very happy with it. Very easy to move even under load. Paul From: CnC-List on behalf of Schiller via CnC-List Sent: Saturday, April 14, 2018 2:29:40 PM To: cnc-list@cnc-list.com Cc: Schiller; Jean-Guy Nadeau

Re: Stus-List IPad Upgrade

Or get a bad elf gps for lightening connector Paul From: CnC-List on behalf of Sam Salter via CnC-List Sent: Tuesday, April 10, 2018 1:51:07 PM To: cnc-list@cnc-list.com Cc: Sam Salter Subject: Re: Stus-List IPad Upgrade Thanks Joel - time to open my walle

Re: Stus-List Questions about 33-2 centerboard

I have a 33-2 KCB, and the big difference is the area under the mast is solid due to the different keel. I was fortunate and had Rob MacLachlan do my pendant when it needed, a bit finicky, but a less than an hour in the slings. We had to feed the new one as the old broke when a friend opened th

Re: Stus-List Geared folding props

Flex-o-fold, no issues opening in forward, a quick shot of power opens fine in reverse, less prop walk than the fixed 2 blades it replaced. Paul From: CnC-List on behalf of Dennis C. via CnC-List Sent: Monday, February 19, 2018 5:52:11 PM To: CnClist Cc: Dennis

Re: Stus-List Raymarine i50 & i60 installation tips?

We use one of these on the wind cable to facilitate the removal of the mast instead of the white box. https://www.defender.com/product.jsp?id=680929 Paul From: CnC-List on behalf of Frederick G Street via CnC-List Sent: Sunday, February 18, 2018 12:43:54 PM To

Re: Stus-List Masthead sheaves for 33-2?

I had garhauer do sheaves for our 33-2, slightly narrower than their stock ones. I sent one of the existing ones to them Get Outlook for iOS From: CnC-List on behalf of Dave S via CnC-List Sent: Saturday, February 17, 2018 11:09:08 AM To:

Re: Stus-List C&C 37+ window replacement

Mark, you want cast and 3/8". The first time mine were done the 'expert' used 1/4 which I did not know until I had both crack after just 3 years. He did not polish or bevel the edges either and did a lot of damage to the opening. When we re did them I got the windows made at SOUTHSHORE as Ro

Re: Stus-List Toronto Boat Show

See you there Chuck - at the Port Credit Yacht Club booth 10-1 Saturday. -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Chuck Gilchrest via CnC-List Sent: Thursday, January 11, 2018 8:10 AM To: cnc-list@cnc-list.com Cc: Chuck Gilchrest Subject: Stu

Re: Stus-List 33-2 owners who have purchased a mantus or rocna anchor. What size did you get?

We have a 22 lb delta with 25’ of chain on our 33-LLP, used it both in North Carolina and now on Lake Ontario with no issues. While in NC, a friend borrowed it to use as his primary anchor during a hurricane (we had hauled out for it) and it held well for him. Get Outlook for iOS

Re: Stus-List Dow Corning Sealant 795

www.dowcorning.com/applications/DistributorFinder/Default.aspx?prod_id=01595717&prod_ids=PROD&state=ON&country=CAN&language=E From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rod Stright via CnC-List Sent: Friday, December 1, 2017 7:18 AM To: cnc-list@cnc-list.com Cc: Rod Strigh

Re: Stus-List C&C 33 MKII

Yes they did and yes I can scan it - may be a couple of days though. -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Stu via CnC-List Sent: Monday, November 20, 2017 2:22 PM To: cnc-list@cnc-list.com Cc: Stu Subject: Stus-List C&C 33 MKII Hi ev

Re: Stus-List AIS improvement + general rewiring

Joe, I bought a Bad Elf for my iPad mini original, worked fine (does with my mini 4 as well, but it also has a built in GPS receiver) with the navionics app and mapsme. The Navionics app works on both my iPhone and iPad – both are ties to the same apple account, so just 1 subscription so far, a

Re: Stus-List New Striping g...

I'll second that - did the stripes and stars on Perception with one - just did a 2 year old hailing port on a friends boat and had more glue to clean up after but also easier than a heat gun and scraping. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Rick Taillieu via CnC-L

Re: Stus-List Charter from Grenada

Tom, Grenada is on the southern end of the hurricane belt, and other than some surge and rain Irma and Maria left it and most of the Grenadines untouched. There is a huge effort amongst the residents and sailors to get aid to Dominica and other affected islands Get Outlook for iOS

Re: Stus-List Charter from Grenada

Have not chartered , but been to Grenada a number of times and love it there. If you are going check out Chris Doyle’s guides and there is a Grenada Cruisers group on Facebook. Get Outlook for iOS From: CnC-List on behalf of David Knecht

Re: Stus-List Painting the headliner

This is what I used on Perception : http://www.homedepot.com/p/4-ft-x-8-ft-White-090-FRP-Wall-Board-MFTF12IXA480009600/100389836 From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Matthew L. Wolford via CnC-List Sent: Tuesday, October 3, 2017 9:09 AM To: cnc-list@cnc-list.com Cc

Re: Stus-List A4 Cutting Out

If the fuel hose is original replace it to - the inner wall can collapse and starve the engine ... -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Randy Stafford via CnC-List Sent: Thursday, September 21, 2017 6:40 PM To: cnc-list@cnc-list.com Cc: R

Re: Stus-List A4 Cutting Out

Check the internal walls of your fuel line is not collapsing - had this on a friends C&C 29 a few years back - -Original Message- From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Randal Stafford via CnC-List Sent: Monday, September 18, 2017 10:30 AM To: cnc-list@cnc-li

Re: Stus-List Depth Sounder

Stus-List Depth Sounder Paul, No. The transducer is at the bottom of Lake Michigan. It went when the mast broke. You can still get new transducers and cables. I think it is $469 for the transducer and cable. Neil Schiller 1983 C&C 35, Mark III, #028 "Grace" White Lake, Michigan

Re: Stus-List Depth Sounder

Neil, Did you keep the wind transducer? I have a friend who needs one from an ST60 (with cable if possible) … From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of schiller via CnC-List Sent: Thursday, September 14, 2017 7:33 AM To: cnc-list@cnc-list.com Cc: schiller Subject: Re:

  1   2   3   >