Ok, this sounds like what I have, so probably that's not going to change
and just have to live with it.
All said and done, I've installed maybe 20 Outbacks out here, and very
very few issues over many years.
On 7/19/2024 12:59 PM, Chris Schaefer wrote:
Not sure if this helps but I had installed a full blown Outback twin
VFX 3648 with two MX60's with the old green cabinets back in 2005.
Last year I had to replace the two inverters with the new FXR as the
VFX is discontinued. In order to do this I had to dump the old oval
mate and move up to the Mate3s, as well as replace the old Hub 10.1
and use the newer 10.3. When all said and done, the Mate saw the old
MX60's but you were unable to make changes or access any
data/settings. One other note, the 2nd inverter goes on port 7 of the
Hub, not port 2 as we've been use to in the past.
Christopher
On Fri, Jul 19, 2024 at 12:30 PM jay via RE-wrenches
<re-wrenches@lists.re-wrenches.org> wrote:
HI Chris,
Can you give us more data?
Like is this a new problem, or it only started after X?
Since its not seeing the port ( NA) it could be the CC or the HUB,
or the cable.
the hub will show an active LED light if its connecting to
anything on that port.
You can try plugging into the CC directly to see if it reads it,
probably easier with another mate.
It just sucks to not have tech support or anyone on wrenches from
some OEMS
Jay
On Jul 19, 2024, at 10:13 AM, Christopher Warfel via RE-wrenches
<re-wrenches@lists.re-wrenches.org> wrote:
This is grid tied system with all firmware updates that the Mate
3s recognizes. I cannot figure this blank data menu out. I have
to program the battery ABS, FLOAT settings from the FM60 CC.
System is 12 years old so no Tech support available even if they
answer the phone....
Has anyone have advice for if this is normal, or if there seems
to be an issue? Used a spare Mate 3s with no difference. Thank
you, Chris
--
Christopher Warfel
ENTECH Engineering Inc.
PO Box 871, Block Island, RI 02807
401-477-5773
<EEIlogolong.jpg> <https://entech-engineering.com/Home/default.php>
<Mate3s Battery Setpoint
Menu.jpg><cwarfel.vcf>_______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work,
try the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
_______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work,
try the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
--
Chris Schaefer’s
/Tel 585-229-2083 or Cell 585-748-1870
//5115 S Hill Road ~ Canandaigua New York 14424
//www.solarandwindfx.com <http://www.solarandwindfx.com> ~ E-mail:
ch...@solarandwindfx.com/
/
/
Thomas Jefferson, the author of our great Constitution, once said,
"democracy" will cease to exist when you take away from those who are
willing to work and give to those who would not."
--
Christopher Warfel
ENTECH Engineering Inc.
PO Box 871, Block Island, RI 02807
401-477-5773
EE Logo <https://entech-engineering.com/Home/default.php>
BEGIN:VCARD
VERSION:4.0
N:Warfel;Christopher;;;
TEL;VALUE=TEXT:401-447-5773 (c)
NOTE:Use the cell phone number for all communications. Thank you.
URL:https://www.entech-engineering.com
END:VCARD
_______________________________________________
List sponsored by Redwood Alliance
Pay optional member dues here: http://re-wrenches.org
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
There are two list archives for searching. When one doesn't work, try the other:
https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
http://www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
http://www.members.re-wrenches.org
