Look at how much build time you lost, Virg On Wed, 29 Mar 2006 11:24:17 +1000 "Chris Johnston" <chr...@ozdocs.net.au> writes: > I was talking to a guy in Queensland last night and he noticed > the same > difference, pondered over the problem for a while, and he eventually > gave up > and just used the same width top and bottom, he tells me there are a > few > grey areas in the plans and this is one of them, soo.... I guess I > will do > the same. > > > > > Chris Johnston > > > > Sydney Australia. > ----- Original Message ----- > From: "VIRGIL N SALISBURY" <virg...@juno.com> > To: <kr...@mylist.net> > Sent: Tuesday, March 28, 2006 12:31 PM > Subject: Re: KR> ruder post > > > > use the width top and bottom the same. Virg > > > > On Tue, 28 Mar 2006 11:57:03 +1000 "Chris Johnston" > > <chr...@ozdocs.net.au> writes: > >> I checked the KR2S plans again, and measured with dividers, > ( > >> from the > >> plan view ), the difference in width between the upper and lower > >> longerons > >> at the front of the rudder post, and the top is wider than the > >> bottom by > >> about 30 percent. Yet in the assembly manual there is a > >> "perspective" view > >> which seems to show no difference in width, the KR2 plans, > again > >> from the > >> plan view show no difference in width???? Confusing! > >> > >> > >> > >> > >> Chris Johnston > >> > >> > >> > >> RICHMOND AUSTRALIA > >> ----- Original Message ----- > >> From: "VIRGIL N SALISBURY" <virg...@juno.com> > >> To: <kr...@mylist.net> > >> Sent: Monday, March 27, 2006 2:23 PM > >> Subject: Re: KR> ruder post > >> > >> > >> > the rudder post on the K R 1 was tilted back 7 Degrees. > >> Taper > >> > front to back > >> > of the post was to meet the aft Fus when sprung in. From > above > >> the Fus, > >> > the only > >> > taper was from the top of the Fus to the tip. Check the top > view > >> of the > >> > plans again, Virg > >> > > >> > On Mon, 27 Mar 2006 13:06:50 +1000 "Chris Johnston" > >> > <chr...@ozdocs.net.au> writes: > >> >> I need some advice on the kr2s rudder post, it looks as > >> though > >> >> from the plans the the section of the rudder post buried in > the > >> aft > >> >> fuselage must be tapered, as the top longerons are wider than > >> the > >> >> bottom longerons, but this section must also be bevelled, how > far > >> up > >> >> do you run the bevel? it looks as though on the kr2, that > there > >> is > >> >> no taper on the lower part of the rudder post? I have > searched > >> the > >> >> archives and not found anything useful and have found no > >> >> construction photos either of anything usefull, but I may > have > >> just > >> >> been looking in all the wrong places. > >> >> > >> >> > >> >> > >> >> > >> >> > >> >> Chris > >> Johnston > >> >> > >> >> > >> >> > >> >> > >> >> > Richmond > >> >> Australia > >> >> _______________________________________ > >> >> Search the KRnet Archives at > >> >> http://www.maddyhome.com/krsrch/index.jsp > >> >> to UNsubscribe from KRnet, send a message to > >> krnet-le...@mylist.net > >> >> please see other KRnet info at http://www.krnet.org/info.html > >> >> > >> >> > >> > > >> > > >> > Virgil N. Salisbury - AMSOIL > >> > www.lubedealer.com/salisbury > >> > Miami ,Fl > >> > > >> > _______________________________________ > >> > Search the KRnet Archives at > >> http://www.maddyhome.com/krsrch/index.jsp > >> > to UNsubscribe from KRnet, send a message to > >> krnet-le...@mylist.net > >> > please see other KRnet info at http://www.krnet.org/info.html > >> > > >> > >> > >> _______________________________________ > >> Search the KRnet Archives at > >> http://www.maddyhome.com/krsrch/index.jsp > >> to UNsubscribe from KRnet, send a message to > krnet-le...@mylist.net > >> please see other KRnet info at http://www.krnet.org/info.html > >> > >> > > > > > > Virgil N. Salisbury - AMSOIL > > www.lubedealer.com/salisbury > > Miami ,Fl > > > > _______________________________________ > > Search the KRnet Archives at > http://www.maddyhome.com/krsrch/index.jsp > > to UNsubscribe from KRnet, send a message to > krnet-le...@mylist.net > > please see other KRnet info at http://www.krnet.org/info.html > > > > > _______________________________________ > Search the KRnet Archives at > http://www.maddyhome.com/krsrch/index.jsp > to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net > please see other KRnet info at http://www.krnet.org/info.html > >
Virgil N. Salisbury - AMSOIL www.lubedealer.com/salisbury Miami ,Fl
