Terry wrote: > Leslie, > > I am not opposed to this change and if there is enough > intrest in this then great. > > I think that a better feature would be a "tool check" > Cutter is loading up(or whatever problem),you hit the > tool check button and the machine would move to a safe location > How would the tool know where the safe location is or how to get to the safe location?
If I'm thread milling on a mill, I can't just pull straight up? If I'm face grooving on a lathe I have to move in one direction, while if I'm cutting off, I have to move in another. Ken > and go into a pause mode.Fix the problem and hit the tool check > button again and machine would go to where it was when the button > was pushed(or maybe the line right before it. > It would be pretty close to what an M01 would do but > with a move away and back. > There is going to drawbacks for this but it might be useful. > > > > Later > > Terry > > > > On Mon Jun 22 4:02 , Leslie Newell <[email protected]> sent: > > >> Hi Terry, >> >> >>> Having a tool presetter or not,at some point in time you have to >>> inform the control how long the next the tool is. >>> >> Of course. >> >> >>> then you put the next tool in and >>> touch it off, write it in the tool table in the T2 line >>> >> You need to manually jog to touch off the tool. It doesn't matter if you >> need MDI or not, you still have to stop the program. Not sure why you >> bother with manually changing the tool table though. The touch off >> button in Axis does it for you, though it needs to be able to use MDI >> mode to do it. >> >> >>> then scroll down to T2M6 in the prog and right click and hit start from >>> here. >>> I think that is pretty easy. >>> >> Yes, but prone to errors, especially if you have a long program with a >> number of tool changes. It is a lot easier to simply press cycle start. >> >> >> >>> Replacing broken tools goes like this for me: >>> Groan loudly hit esc,jog out of the way,pick up >>> what is left of the tool and throw it at >>> the wall as hard as I can. >>> >> LOL. Being able to jog halfway through a job doesn't really help with >> this situation. Unless you have superhuman reflexes you will still have >> to back up the program to the point where the cutter failed. >> >> >> However, where it is really useful is if the cutter starts loading up >> with swarf. I regularly machine sheet plastic (acrylic engraving >> laminate). While plunging the cutter often gets a lot of swarf wrapped >> around it. After a couple of plunges you end up with enough tied around >> the cutter to start rubbing and burning the surface of the work. You >> then need to pause, lift the cutter and clear the swarf. This is a >> production job, not hobby use. I have experienced similar problems often >> enough on my lathe as well. >> >> >> >>> I view the developers time as super-valuable and would not >>> like to see them spend time on this when there are other more >>> important things on their plate. >>> >> My point is that being able to jog/use MDI during a manual tool change >> should be a relatively trivial task that makes life a easier for a lot >> of EMC users. The other day I was talking to an OEM who was trying to >> choose between EMC and Mach. He was pretty enthusiastic about EMC until >> I told him you can't jog during a tool change. As far as he was >> concerned that was a show stopper and he went for Mach. >> >> Being able to jog during pause is not nearly as easy and would involve >> quite a bit of work. >> >> Les >> > > > ---- Msg sent via CableONE.net MyMail - http://www.cableone.net > ------------------------------------------------------------------------------ > Are you an open source citizen? Join us for the Open Source Bridge conference! > Portland, OR, June 17-19. Two days of sessions, one day of unconference: $250. > Need another reason to go? 24-hour hacker lounge. Register today! > http://ad.doubleclick.net/clk;215844324;13503038;v?http://opensourcebridge.org > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users > -- Kenneth Lerman Mark Kenny Products Company, LLC 55 Main Street Newtown, CT 06470 888-ISO-SEVO 203-426-7166 ------------------------------------------------------------------------------ Are you an open source citizen? Join us for the Open Source Bridge conference! Portland, OR, June 17-19. Two days of sessions, one day of unconference: $250. Need another reason to go? 24-hour hacker lounge. Register today! http://ad.doubleclick.net/clk;215844324;13503038;v?http://opensourcebridge.org _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
