Thank you Philip! I also don't have the audio jack working. Should I ask it on the meta-xilinx list?
On Wed, Apr 1, 2015 at 4:50 PM, Philip Balister <phi...@balister.org> wrote: > On 03/31/2015 11:39 AM, Alireza Khodamoradi wrote: > > Philip, > > > > I got it working. For some reason if I use *Ubuntu's Archive Manager* on > my > > laptop to uncompress the .xz file, it doesn't work! > > > > I had to uncompress it by this command: *unxz -d > > sdimage-8G-zedboard.direct.xz* in order to get it work. > > > > Now I have a linux running on the zedboard with the gnu-radio. But I > can't > > get the VGA to work - I have to use UART to connect to the linux - I saw > it > > has *startx* , is there any way for me to get the VGA working? > > I'd ask on the meta-xilinx list. We use hte BSP from Xilinx, which I do > not think has support for the video display. For that you need a special > driver (and I believe you need some stuff in the fpga). The build we > have doesn't depend on anything loaded in the fpga. > > Philip > > > > > Thank you, > > Alireza > > > > On Fri, Mar 20, 2015 at 6:54 AM, Philip Balister <phi...@balister.org> > > wrote: > > > >> On 03/19/2015 10:48 AM, Alireza Khodamoradi wrote: > >>> Here are the files I have in the FAT partition (boot): > >>> > >>> 1- boot.bin > >>> 2- u-boot.img > >>> 3- uEnv.txt > >>> 4- uImage > >>> 5- zc702-zynq7.dtb > >>> > >>> * I used this image: *sdimage-8G-zc702.direct* > >> > >> So this all looks correct. When you put the card in the PC both the FAT > >> and roofs partitions are mounted OK? You did use an 8G card? > >> > >> I'm not sure what to say at this point. Everything looks OK. I am > >> traveling and away from borads for a few weeks. > >> > >> Philip > >> > >>> > >>> On Thu, Mar 19, 2015 at 6:41 AM, Philip Balister <phi...@balister.org> > >>> wrote: > >>> > >>>> On 03/18/2015 10:44 PM, Alireza Khodamoradi wrote: > >>>>> Philip, > >>>>> > >>>>> Thank you for letting me using your images. I tried both of them with > >>>> the *dd > >>>>> *command, it took me around 2000 seconds (30 mins) each and after > using > >>>>> them on the board I get the following message via the UART: > >>>>> > >>>>> *U-Boot SPL 2014.01 (Jan 09 2015 - 20:24:45)* > >>>>> *mmc boot* > >>>>> *reading fpga.bin* > >>>>> *spl: error reding image fpga.bin, err - -1* > >>>>> *reading system.dtb* > >>>>> *spl: error reading image system.dtb, err - -1* > >>>>> *reading u-boot.img* > >>>>> *spl: error reading image u-boot.img, err - -1* > >>>>> *### ERROR ### Please RESET the board ###* > >>>> > >>>> So the first stage boot loader is running, which is good. > >>>> > >>>> It looks for a couple of files which should be there, which is OK. > >>>> (fpga.bin and system.dtb) > >>>> > >>>> Then it tries to load u-boot.img which it doesn't find. This is bad. > >>>> > >>>> Can you put the card in a PC and send the list of file in the FAT > >>>> partition? > >>>> > >>>> Philip > >>>> > >>>> > >>>>> > >>>>> I got the above message for sdimage-8G-zc702.direct. I get no message > >> for > >>>>> the other image. > >>>>> > >>>>> What am I doing wrong? > >>>>> > >>>>> On Fri, Mar 13, 2015 at 11:22 AM, Philip Balister < > phi...@balister.org > >>> > >>>>> wrote: > >>>>> > >>>>>> On 03/13/2015 01:17 PM, Alireza Khodamoradi wrote: > >>>>>>> Hello everyone, > >>>>>>> > >>>>>>> I'm going through the instructions from here: > >>>>>>> > >>>>>>> http://gnuradio.org/redmine/projects/gnuradio/wiki/Zynq > >>>>>> > >>>>>> I should go over those carefully, but in the mentime I have some > >> images > >>>>>> built for the zedbaord here: > >>>>>> > >>>>>> > >>>> > >> > https://www.dropbox.com/sh/yfbpj63pcenqatr/AAAt0s3xFXs47I7q5pNopheHa?dl=0 > >>>>>> > >>>>>> Take the zedboard one, uncompress it and write it to an sd card. Be > >> sure > >>>>>> to unmount (not eject) the sd card and run: > >>>>>> > >>>>>> sudo dd if=sdimage-8G-zedboard.direct of=/dev/sdX > >>>>>> > >>>>>> where sdx is the device the sd card is on. > >>>>>> > >>>>>> Philip > >>>>>> > >>>>>>> > >>>>>>> to get a working image with gnu radio for my zedboard. > >>>>>>> > >>>>>>> Unfortunately I can't get the board to boot with this image. I was > >>>>>>> wondering if someone can help me. > >>>>>>> > >>>>>>> what I tried so far ( all failed - can't boot from the SDCard): > >>>>>>> > >>>>>>> - default settings in the instructions > >>>>>>> - renaming u-boot.bin to boot.bin > >>>>>>> - renaming u-boot.bin to BOOT.BIN > >>>>>>> - renaming uImage--zedboard-zynq7.dtb to devicetree.dtb > >>>>>>> - I tried command line as well as gparted gui. > >>>>>>> > >>>>>>> what I checked: > >>>>>>> > >>>>>>> - download a linux from XillyBus and boot the board with SDCard -> > >>>> works > >>>>>>> > >>>>>>> v/r > >>>>>>> Alireza > >>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> _______________________________________________ > >>>>>>> Discuss-gnuradio mailing list > >>>>>>> Discuss-gnuradio@gnu.org > >>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio > >>>>>>> > >>>>>> > >>>>> > >>>> > >>> > >> > > >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
