Here are the files I have in the FAT partition (boot): 1- boot.bin 2- u-boot.img 3- uEnv.txt 4- uImage 5- zc702-zynq7.dtb
* I used this image: *sdimage-8G-zc702.direct* On Thu, Mar 19, 2015 at 6:41 AM, Philip Balister <phi...@balister.org> wrote: > On 03/18/2015 10:44 PM, Alireza Khodamoradi wrote: > > Philip, > > > > Thank you for letting me using your images. I tried both of them with > the *dd > > *command, it took me around 2000 seconds (30 mins) each and after using > > them on the board I get the following message via the UART: > > > > *U-Boot SPL 2014.01 (Jan 09 2015 - 20:24:45)* > > *mmc boot* > > *reading fpga.bin* > > *spl: error reding image fpga.bin, err - -1* > > *reading system.dtb* > > *spl: error reading image system.dtb, err - -1* > > *reading u-boot.img* > > *spl: error reading image u-boot.img, err - -1* > > *### ERROR ### Please RESET the board ###* > > So the first stage boot loader is running, which is good. > > It looks for a couple of files which should be there, which is OK. > (fpga.bin and system.dtb) > > Then it tries to load u-boot.img which it doesn't find. This is bad. > > Can you put the card in a PC and send the list of file in the FAT > partition? > > Philip > > > > > > I got the above message for sdimage-8G-zc702.direct. I get no message for > > the other image. > > > > What am I doing wrong? > > > > On Fri, Mar 13, 2015 at 11:22 AM, Philip Balister <phi...@balister.org> > > wrote: > > > >> On 03/13/2015 01:17 PM, Alireza Khodamoradi wrote: > >>> Hello everyone, > >>> > >>> I'm going through the instructions from here: > >>> > >>> http://gnuradio.org/redmine/projects/gnuradio/wiki/Zynq > >> > >> I should go over those carefully, but in the mentime I have some images > >> built for the zedbaord here: > >> > >> > https://www.dropbox.com/sh/yfbpj63pcenqatr/AAAt0s3xFXs47I7q5pNopheHa?dl=0 > >> > >> Take the zedboard one, uncompress it and write it to an sd card. Be sure > >> to unmount (not eject) the sd card and run: > >> > >> sudo dd if=sdimage-8G-zedboard.direct of=/dev/sdX > >> > >> where sdx is the device the sd card is on. > >> > >> Philip > >> > >>> > >>> to get a working image with gnu radio for my zedboard. > >>> > >>> Unfortunately I can't get the board to boot with this image. I was > >>> wondering if someone can help me. > >>> > >>> what I tried so far ( all failed - can't boot from the SDCard): > >>> > >>> - default settings in the instructions > >>> - renaming u-boot.bin to boot.bin > >>> - renaming u-boot.bin to BOOT.BIN > >>> - renaming uImage--zedboard-zynq7.dtb to devicetree.dtb > >>> - I tried command line as well as gparted gui. > >>> > >>> what I checked: > >>> > >>> - download a linux from XillyBus and boot the board with SDCard -> > works > >>> > >>> v/r > >>> Alireza > >>> > >>> > >>> > >>> _______________________________________________ > >>> Discuss-gnuradio mailing list > >>> Discuss-gnuradio@gnu.org > >>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio > >>> > >> > > >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
