So do we have some agreement:


1.      Best material for windows Plexiglass of similar product
2.      Best application 3M VHB 5952 tape
3.      Best sealant Dow Corning 795 or Pecora 895  (same properties)
4.      Paint behind windows black or coloring the area behind the window 
(cavity) that is not taped to improve the appearance. ??? I believe I read 
somewhere black paint will work fine but will someone who has done it please 
confirm?
5.      Once windows are taped in place mask well and force sealant into edge 
of window.
6.      Smooth sealant with a plastic spoon or some other device to create a 
smooth finish
7.      Allow to cure a bit prior to removing masking tape so that the sealant 
peels off better.



Rod

2004 C&C 99

Halifax



From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of svpegasus38 
via CnC-List
Sent: December-14-17 3:41 PM
To: cnc-list@cnc-list.com
Cc: svpegasus38 <svpegasu...@gmail.com>
Subject: Re: Stus-List Window replacement



I figure 1 tube per side. All depends on gap and application technique.







Sent from my T-Mobile 4G LTE Device

Doug Mountjoy

POYC

Rebecca Leah

Lf39



-------- Original message --------

From: "Matthew L. Wolford via CnC-List" <cnc-list@cnc-list.com 
<mailto:cnc-list@cnc-list.com> >

Date: 12/14/17 11:03 (GMT-08:00)

To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>

Cc: "Matthew L. Wolford" <wolf...@erie.net <mailto:wolf...@erie.net> >

Subject: Re: Stus-List Window replacement



Last question:  will one tube of caulking do four windows?



From: Dennis C. via CnC-List <mailto:cnc-list@cnc-list.com>

Sent: Thursday, December 14, 2017 1:51 PM

To: CnClist <mailto:cnc-list@cnc-list.com>

Cc: Dennis C. <mailto:capt...@gmail.com>

Subject: Re: Stus-List Window replacement



This might be why 3M recommends the 5952:



*        Creates a permanent seal against water, moisture and more by offering 
better gap filling capabilities

That's in the 5952 description on the 3M site.  It does not appear in the 4941 
description.  Could be the 5952 is more closed cell foam than the 4941.



Dennis C.



On Thu, Dec 14, 2017 at 12:41 PM, Matthew L. Wolford via CnC-List 
<cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com> > wrote:

Incidentally, I noted in a previous e-mail that a 3M rep I talked to (by 
calling in) recommended 5952 over 4941.  I just inquired again – this time by 
e-mail.  3M responded that that it recommends the 59XX series for this 
application.  For what it’s worth.



  _____

_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray



---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________

Thanks everyone for supporting this list with your contributions.  Each and 
every one is greatly appreciated.  If you want to support the list - use PayPal 
to send contribution --   https://www.paypal.me/stumurray

Reply via email to