The other question is which of the 3 available transducers what would be the one needed for my boat all FG. They have a thru hull plastic or bronze. they have a in-hull puck and a transom mounted one. I will not be using it for fishing just for anchoring.
On Fri, Dec 13, 2013 at 1:35 PM, Jim Watts <paradigmat...@gmail.com> wrote: > Here's a pic of it in operation. It worked very well. Thanks again, Bill. > > http://farm4.staticflickr.com/3720/11356246664_97ff1bb057_h.jpg > > It also worked to press the new bearing in. > > http://members.shaw.ca/parmesanshift/images/IMG_2428.jpg > > > On 13 December 2013 09:18, Robert Abbott <robertabb...@eastlink.ca> wrote: > >> Josh: >> >> I believe Dwight Venoit on this list made a tool to remove a cutlass >> bearing ......he will respond when he reads this....stay tuned! >> >> >> Rob Abbott >> AZURA >> C&C 32 - 84 >> Halifax, N.S. >> >> >> On 2013/12/13 11:57 AM, Joel Aronson wrote: >> >> Josh, >> >> I'm trying to avoid the step of "removing the shaft". Internet wisdom >> also says you can make your own tool, but I don't know if I can find >> something sized properly to push out the old one. If the yard has the tool >> I may pay them to do it. >> >> Joel >> >> On Friday, December 13, 2013, Josh Muckley wrote: >> >>> Internet wisdom says that if you don't mind removing the shaft, a hack >>> saw threaded up the cutlass will remove it and a length of all thread and >>> some washers will install it. Let us know what works. >>> >>> Good luck, >>> Josh >>> On Dec 13, 2013 9:54 AM, "Joel Aronson" <joel.aron...@gmail.com> wrote: >>> >>>> For 50 I would buy it. The one I saw was 400! Can you point me in the >>>> right direction? >>>> >>>> On Friday, December 13, 2013, Josh Muckley wrote: >>>> >>>>> Nope, but if you end up buying one... I remember seeing one where you >>>>> didn't have to remove the shaft. I think it ran about $50. >>>>> >>>>> Josh >>>>> On Dec 13, 2013 8:28 AM, "Joel Aronson" <joel.aron...@gmail.com> >>>>> wrote: >>>>> >>>>>> All, >>>>>> >>>>>> Does anyone in the Annapolis area have a cutlass bearing removal >>>>>> tool for a 1 inch shaft that I could borrow? >>>>>> >>>>>> Thanks! >>>>>> Joel >>>>>> 35/3 >>>>>> The Office >>>>>> Annapolis >>>>>> >>>>>> >>>>>> -- >>>>>> Joel >>>>>> 301 541 8551 >>>>>> >>>>>> _______________________________________________ >>>>>> This List is provided by the C&C Photo Album >>>>>> http://www.cncphotoalbum.com >>>>>> CnC-List@cnc-list.com >>>>>> >>>>>> >>>> >>>> -- >>>> Joel >>>> 301 541 8551 >>>> >>>> _______________________________________________ >>>> This List is provided by the C&C Photo Album >>>> http://www.cncphotoalbum.com >>>> CnC-List@cnc-list.com >>>> >>>> >> >> -- >> Joel >> 301 541 8551 >> >> >> _______________________________________________ >> This List is provided by the C&C Photo >> Albumhttp://www.cncphotoalbum.comcnc-l...@cnc-list.com >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> >> > > > -- > Jim Watts > Paradigm Shift > C&C 35 Mk III > Victoria, BC > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > -- “Sailors, with their built in sense of order, service and discipline, should really be running the world.” - Nicholas Monsarrat
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
