Appreciate it if you do. Sent from my iPad
On Aug 5, 2012, at 8:22 AM, Joel Aronson <joel.aron...@gmail.com> wrote: > I can take pic of my 35/3. > > Joel Aronson > > > On Aug 5, 2012, at 9:17 AM, Bill Striegel <wstrie...@cableone.net> wrote: > >> Yes,the floor bolt is there. Any pics would be appreciated. >> >> Sent from my iPad >> >> On Aug 5, 2012, at 7:16 AM, Graham Collins <gcoll...@hfx.eastlink.ca> wrote: >> >>> HI Bill >>> On my boat the hardware between keel and track looks to be generic shroud >>> hardware, the only non standard bit is the bolt into the floor - I don't >>> know how that is fastened in. Hopefully you still have that bit of >>> hardware in place! >>> >>> If you go synthetic try Colligo marine. >>> >>> regards, >>> Graham Collins >>> Secret Plans >>> C&C 35-3 >>> >>> Bill Striegel wrote: >>>> Where might I get the bolt attachments to attach the rod/high tech >>>> synthetic to? Shroud rigging? >>>> Tks. >>>> >>>> Bill Striegel >>>> 1982 C&C 34 >>>> "Panacea" >>>> Ocean Springs, MS >>>> >>>> Sent from my iPad >>>> >>>> On Aug 4, 2012, at 7:28 PM, "John and Maryann Read"<johnpr...@comcast.net> >>>> wrote: >>>> >>>>> Bill >>>>> >>>>> On our 34, there is a stainless rod attaching the babystay track to the >>>>> keel. It is much like your shrouds. It is located in the forward v berth >>>>> area just forward of the bulkhead for the head. The upper end is attached >>>>> to a bolt which is through the deck and track, the lower end is screwed >>>>> through the floor into the forward edge of the keel. There is a >>>>> turnbuckle >>>>> for adjustment. Without this rod, the babystay tension would pull the >>>>> track >>>>> out of the deck. >>>>> >>>>> Hope this helps >>>>> >>>>> John and Maryann >>>>> Legacy III >>>>> 1982 C&C 34 >>>>> Noank, CT >>>>> -----Original Message----- >>>>> From: cnc-list-boun...@cnc-list.com [mailto:cnc-list-boun...@cnc-list.com] >>>>> On Behalf Of Bill Striegel >>>>> Sent: Saturday, August 04, 2012 10:14 AM >>>>> To: cnc-list@cnc-list.com >>>>> Subject: Re: Stus-List C&C 34: baby stay deck hardware >>>>> >>>>> I also cannot find the interior rod to secure the track below in the v >>>>> berth.any pics? Could lone use high tech rope? How was it attached. To the >>>>> bolts and the one on the floor? Where can one purchase the screw on >>>>> attachment points? >>>>> >>>>> Sent from my iPad >>>>> >>>>> On Aug 3, 2012, at 6:36 AM, Bill Striegel<wstrie...@cableone.net> wrote: >>>>> >>>>>> Is this correct? I need to remount it on the deck. Two block atop each >>>>> other go forward.moveable car bumper to stern. Line arrangement: tie line >>>>> to >>>>> forward eye on car,then around top block,then around thimble on car,then >>>>> around lower block forward,then line to deck V-cleat? The aft thimble on >>>>> the car is not used. Correct? >>>>>> Ps: anyone w picture? >>>>>> >>>>>> >>>>>> Bill Striegel >>>>>> Ocean Springs,MS >>>>>> Sent from my iPad >>>>>> _______________________________________________ >>>>>> This List is provided by the C&C Photo Album >>>>>> http://www.cncphotoalbum.com CnC-List@cnc-list.com >>>>> _______________________________________________ >>>>> This List is provided by the C&C Photo Album http://www.cncphotoalbum.com >>>>> CnC-List@cnc-list.com >>>>> >>>>> >>>>> _______________________________________________ >>>>> This List is provided by the C&C Photo Album >>>>> http://www.cncphotoalbum.com >>>>> CnC-List@cnc-list.com >>>> _______________________________________________ >>>> This List is provided by the C&C Photo Album >>>> http://www.cncphotoalbum.com >>>> CnC-List@cnc-list.com >>>> >>> >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
