I can take pic of my 35/3. Joel Aronson
On Aug 5, 2012, at 9:17 AM, Bill Striegel <wstrie...@cableone.net> wrote: > Yes,the floor bolt is there. Any pics would be appreciated. > > Sent from my iPad > > On Aug 5, 2012, at 7:16 AM, Graham Collins <gcoll...@hfx.eastlink.ca> wrote: > >> HI Bill >> On my boat the hardware between keel and track looks to be generic shroud >> hardware, the only non standard bit is the bolt into the floor - I don't >> know how that is fastened in. Hopefully you still have that bit of hardware >> in place! >> >> If you go synthetic try Colligo marine. >> >> regards, >> Graham Collins >> Secret Plans >> C&C 35-3 >> >> Bill Striegel wrote: >>> Where might I get the bolt attachments to attach the rod/high tech >>> synthetic to? Shroud rigging? >>> Tks. >>> >>> Bill Striegel >>> 1982 C&C 34 >>> "Panacea" >>> Ocean Springs, MS >>> >>> Sent from my iPad >>> >>> On Aug 4, 2012, at 7:28 PM, "John and Maryann Read"<johnpr...@comcast.net> >>> wrote: >>> >>>> Bill >>>> >>>> On our 34, there is a stainless rod attaching the babystay track to the >>>> keel. It is much like your shrouds. It is located in the forward v berth >>>> area just forward of the bulkhead for the head. The upper end is attached >>>> to a bolt which is through the deck and track, the lower end is screwed >>>> through the floor into the forward edge of the keel. There is a turnbuckle >>>> for adjustment. Without this rod, the babystay tension would pull the >>>> track >>>> out of the deck. >>>> >>>> Hope this helps >>>> >>>> John and Maryann >>>> Legacy III >>>> 1982 C&C 34 >>>> Noank, CT >>>> -----Original Message----- >>>> From: cnc-list-boun...@cnc-list.com [mailto:cnc-list-boun...@cnc-list.com] >>>> On Behalf Of Bill Striegel >>>> Sent: Saturday, August 04, 2012 10:14 AM >>>> To: cnc-list@cnc-list.com >>>> Subject: Re: Stus-List C&C 34: baby stay deck hardware >>>> >>>> I also cannot find the interior rod to secure the track below in the v >>>> berth.any pics? Could lone use high tech rope? How was it attached. To the >>>> bolts and the one on the floor? Where can one purchase the screw on >>>> attachment points? >>>> >>>> Sent from my iPad >>>> >>>> On Aug 3, 2012, at 6:36 AM, Bill Striegel<wstrie...@cableone.net> wrote: >>>> >>>>> Is this correct? I need to remount it on the deck. Two block atop each >>>> other go forward.moveable car bumper to stern. Line arrangement: tie line >>>> to >>>> forward eye on car,then around top block,then around thimble on car,then >>>> around lower block forward,then line to deck V-cleat? The aft thimble on >>>> the car is not used. Correct? >>>>> Ps: anyone w picture? >>>>> >>>>> >>>>> Bill Striegel >>>>> Ocean Springs,MS >>>>> Sent from my iPad >>>>> _______________________________________________ >>>>> This List is provided by the C&C Photo Album >>>>> http://www.cncphotoalbum.com CnC-List@cnc-list.com >>>> _______________________________________________ >>>> This List is provided by the C&C Photo Album http://www.cncphotoalbum.com >>>> CnC-List@cnc-list.com >>>> >>>> >>>> _______________________________________________ >>>> This List is provided by the C&C Photo Album >>>> http://www.cncphotoalbum.com >>>> CnC-List@cnc-list.com >>> _______________________________________________ >>> This List is provided by the C&C Photo Album >>> http://www.cncphotoalbum.com >>> CnC-List@cnc-list.com >>> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com _______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
