BananaPro succesfull install on ~current. SD card is recognized. What was
needed to boot after the succesfull install was to once again mount FAT
partition of the SD card and again remove sun7i-a20-cubieboard2.dtb and
copy sun7i-a20-bananapro.dtb to it - i.e. to repeat the same as was needed
to make the same SD card bootable for install.
$ dmesg
OpenBSD 6.2-current (GENERIC) #143: Sun Dec 17 17:26:09 MST 2017
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 1072078848 (1022MB)
avail mem = 1042214912 (993MB)
mainbus0 at root: LeMaker Banana Pro
cpu0 at mainbus0: ARM Cortex-A7 r0p4 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
cortex0 at mainbus0
psci0 at mainbus0
sxiccmu0 at mainbus0
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
sxipio0 at simplebus0: 175 pins
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
sximmc1 at simplebus0
sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
sxiahci0 at simplebus0: AHCI 1.1
scsibus0 at sxiahci0: 32 targets
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
sxidog0 at simplebus0
sxirtc0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
com1 at simplebus0: ns16550, no working fifo
com2 at simplebus0: ns16550, no working fifo
sxitwi0 at simplebus0
iic0 at sxitwi0
axppmic0 at iic0 addr 0x34: AXP209, VBUS
sxitwi1 at simplebus0
iic1 at sxitwi1
dwge0 at simplebus0
dwge0: address: 02:17:04:40:c0:cc
rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
ampintc0 at simplebus0 nirq 160, ncpu 2
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio0: 32 pins
simplefb0 at mainbus0: 656x536
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0 added (std, vt100 emulation)
scsibus1 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <SD/MMC, SL16G, 0030> SCSI2 0/direct removable
sd0: 14804MB, 512 bytes/sector, 30318592 sectors
(manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
(manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd0a (def19b298bca3750.a) swap on sd0b dump on sd0b
On Sat, May 27, 2017 at 12:14 PM, Guillaume Simon <
guillaume.si...@mailoo.org> wrote:
> Hello,
>
> For what it's worth, I have the same issue on a bananapi M1 (tested on
> 6.1 release and current).
> It remains possible to install openBSD on an USB stick and boot from it
> by changing boot_targets order.
>
> ======
>
>
> U-Boot SPL 2017.03 (Apr 01 2017 - 16:15:11)
> DRAM: 1024 MiB
> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> Trying to boot from MMC1
>
>
> U-Boot 2017.03 (Apr 01 2017 - 16:15:11 -0600) Allwinner Technology
>
> CPU: Allwinner A20 (SUN7I)
> Model: LeMaker Banana Pi
> I2C: ready
> DRAM: 1 GiB
> MMC: SUNXI SD/MMC: 0
> Setting up a 720x576i composite-pal console (overscan 32x20)
> In: serial
> Out: vga
> Err: vga
> SCSI: SATA link 0 timeout.
> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> Net: eth0: ethernet@01c50000
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB OHCI 1.0
> USB2: USB EHCI 1.00
> USB3: USB OHCI 1.0
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning bus 2 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot: 0
>
> USB device 0: unknown device
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> reading /sun7i-a20-bananapi.dtb
> 35071 bytes read in 30 ms (1.1 MiB/s)
> Found EFI removable media binary efi/boot/bootarm.efi
> reading efi/boot/bootarm.efi
> 64684 bytes read in 41 ms (1.5 MiB/s)
> ## Starting EFI application at 42000000 ...
> Scanning disks on scsi...
> Scanning disks on usb...
> Scanning disks on mmc...
> MMC Device 1 not found
> MMC Device 2 not found
> MMC Device 3 not found
> Found 6 disks
> >> OpenBSD/armv7 BOOTARM 0.5
> boot>
> cannot open sd0a:/etc/random.seed: No such file or directory
> booting sd0a:/bsd: 2174740+7984008+439148 [80+305280+145318]=0xa8e908
>
> OpenBSD/armv7 booting ...
> arg0 0xc0d8e908 arg1 0x0 arg2 0x48000000
> Allocating page tables
> freestart = 0x40d8f000, free_pages = 258267 (0x0003f0db)
> IRQ stack: p0x40dbd000 v0xc0dbd000
> ABT stack: p0x40dbe000 v0xc0dbe000
> UND stack: p0x40dbf000 v0xc0dbf000
> SVC stack: p0x40dc0000 v0xc0dc0000
> Creating L1 page table at 0x40d90000
> Mapping kernel
> Constructing L2 page tables
> undefined page pmap board type: 0
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2017 OpenBSD. All rights reserved.
> https://www.OpenBSD.org
>
> OpenBSD 6.1-current (RAMDISK) #131: Thu May 25 12:58:19 MDT 2017
> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> real mem = 1072078848 (1022MB)
> avail mem = 1036992512 (988MB)
> mainbus0 at root: LeMaker Banana Pi
> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> cortex0 at mainbus0
> sxiccmu0 at mainbus0
> psci0 at mainbus0
> agtimer0 at mainbus0: tick rate 24000 KHz
> simplebus0 at mainbus0: "soc"
> sxipio0 at simplebus0: 175 pins
> sximmc0 at simplebus0
> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> ehci0 at simplebus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> sxiahci0 at simplebus0: AHCI 1.1
> scsibus0 at sxiahci0: 32 targets
> ehci1 at simplebus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> sxidog0 at simplebus0
> sxirtc0 at simplebus0
> com0 at simplebus0: ns16550, no working fifo
> com0: console
> com1 at simplebus0: ns16550, no working fifo
> com2 at simplebus0: ns16550, no working fifo
> dwge0 at simplebus0
> dwge0: address: 02:0c:04:02:72:70
> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> ampintc0 at simplebus0 nirq 160, ncpu 2
> gpio0 at sxipio0: 32 pins
> gpio1 at sxipio0: 32 pins
> gpio2 at sxipio0: 32 pins
> gpio3 at sxipio0: 32 pins
> gpio4 at sxipio0: 32 pins
> gpio5 at sxipio0: 32 pins
> gpio6 at sxipio0: 32 pins
> gpio7 at sxipio0: 32 pins
> gpio8 at sxipio0: 32 pins
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sdmmc0: can't enable card
> sximmc0: timeout updating clock
> boot device: lookup 'sd0a:/bsd' failed.
> root on rd0a swap on rd0b dump on rd0b
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/armv7 6.1 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
> At any prompt except password prompts you can escape to a shell by
> typing '!'. Default answers are shown in []'s and are selected by
> pressing RETURN. You can exit this program at any time by pressing
> Control-C, but this can leave your system in an inconsistent state.
>
> Terminal type? [vt220]
> System hostname? (short form, e.g. 'foo') mybanana
>
> Available network interfaces are: dwge0.
> Which network interface do you wish to configure? (or 'done') [dwge0] done
> DNS domain name? (e.g. 'bar.com') [my.domain]
> DNS nameservers? (IP address list or 'none') [none]
>
> Password for root account? (will not echo)
> Password for root account? (again)
> Start sshd(8) by default? [yes]
> Setup a user? (enter a lower-case loginname, or 'no') [no]
> Since no user was setup, root logins via sshd(8) might be useful.
> WARNING: root is targeted by password guessing attacks, pubkeys are safer.
> Allow root ssh login? (yes, no, prohibit-password) [no]
>
> Available disks are: none.
> Which disk is the root disk? ('?' for details)
>
>
>
> Le 04/09/17 à 13:13, soko.tica a écrit :
> > Hello,
> >
> > As an update, ~current of April 8, 2017, still doesn't recognize sd card
> of
> > the referred BananaPro. I should probably mention that sd card is 16GB
> > size, unlike up to 4GB cards for the mother device (possibly both
> BananaPi
> > and Cubieboard). Install script and dmesg follow.
> >
> > ======
> > Script started on Sun Apr 9 12:50:19 2017
> > $ cu -l cuaU0 -s 115200
> > Connected to /dev/cuaU0 (speed 115200)
> >
> > U-Boot SPL 2016.07 (Jul 26 2016 - 02:49:44)
> > DRAM: 1024 MiB
> > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> > Trying to boot from MMC1
> >
> >
> > U-Boot 2016.07 (Jul 26 2016 - 02:49:44 -0600) Allwinner Technology
> >
> > CPU: Allwinner A20 (SUN7I)
> > Model: LeMaker Banana Pro
> > I2C: ready
> > DRAM: 1 GiB
> > MMC: SUNXI SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> >
> > Setting up a 720x576i composite-pal console (overscan 32x20)
> > In: serial
> > Out: vga
> > Err: vga
> > SCSI: SATA link 0 timeout.
> > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> > flags: ncq stag pm led clo only pmp pio slum part ccc apst
> > Net: eth0: ethernet@01c50000
> > starting USB...
> > USB0: USB EHCI 1.00
> > USB1: USB OHCI 1.0
> > USB2: USB EHCI 1.00
> > USB3: USB OHCI 1.0
> > scanning bus 0 for devices... 1 USB Device(s) found
> > scanning bus 2 for devices... 1 USB Device(s) found
> > Hit any key to stop autoboot: 0
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > Found EFI removable media binary efi/boot/bootarm.efi
> > reading efi/boot/bootarm.efi
> > 64684 bytes read in 44 ms (1.4 MiB/s)
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> > ## Starting EFI application at 0x42000000 ...
> > Scanning disks on scsi...
> > Scanning disks on usb...
> > Scanning disks on mmc...
> > MMC Device 1 not found
> > MMC Device 2 not found
> > MMC Device 3 not found
> > Found 6 disks
> >>> OpenBSD/armv7 BOOTARM 0.5
> > boot>
> > cannot open sd0a:/etc/random.seed: No such file or directory
> > booting sd0a:/bsd: 2153176+7983908+438864 [80+301584+143437]=0xa851c0
> >
> > OpenBSD/armv7 booting ...
> > arg0 0xc0d851c0 arg1 0x0 arg2 0x48000000
> > Allocating page tables
> > freestart = 0x40d86000, free_pages = 258276 (0x0003f0e4)
> > IRQ stack: p0x40db4000 v0xc0db4000
> > ABT stack: p0x40db5000 v0xc0db5000
> > UND stack: p0x40db6000 v0xc0db6000
> > SVC stack: p0x40db7000 v0xc0db7000
> > Creating L1 page table at 0x40d88000
> > Mapping kernel
> > Constructing L2 page tables
> > undefined page pmap board type: 0
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights reserved.
> > Copyright (c) 1995-2017 OpenBSD. All rights reserved.
> > https://www.OpenBSD.org
> >
> > OpenBSD 6.1-current (RAMDISK) #84: Sat Apr 8 17:04:11 MDT 2017
> > dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> > real mem = 1072078848 (1022MB)
> > avail mem = 1037033472 (988MB)
> > mainbus0 at root: LeMaker Banana Pro
> > cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> > cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> > cortex0 at mainbus0
> > psci0 at mainbus0
> > agtimer0 at mainbus0: tick rate 24000 KHz
> > sxiccmu0 at mainbus0
> > simplebus0 at mainbus0: "soc"
> > sxipio0 at simplebus0: 175 pins
> > sximmc0 at simplebus0
> > sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> > sximmc1 at simplebus0
> > sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> > ehci0 at simplebus0
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> > 2.00/1.00 addr 1
> > sxiahci0 at simplebus0: AHCI 1.1
> > scsibus0 at sxiahci0: 32 targets
> > ehci1 at simplebus0
> > usb1 at ehci1: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> > 2.00/1.00 addr 1
> > sxidog0 at simplebus0
> > sxirtc0 at simplebus0
> > com0 at simplebus0: ns16550, no working fifo
> > com0: console
> > com1 at simplebus0: ns16550, no working fifo
> > com2 at simplebus0: ns16550, no working fifo
> > dwge0 at simplebus0
> > dwge0: Ethernet address: 02:17:04:40:c0:cc
> > rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> > ampintc0 at simplebus0 nirq 160, ncpu 2
> > gpio0 at sxipio0: 32 pins
> > gpio1 at sxipio0: 32 pins
> > gpio2 at sxipio0: 32 pins
> > gpio3 at sxipio0: 32 pins
> > gpio4 at sxipio0: 32 pins
> > gpio5 at sxipio0: 32 pins
> > gpio6 at sxipio0: 32 pins
> > gpio7 at sxipio0: 32 pins
> > gpio8 at sxipio0: 32 pins
> > sximmc0: timeout updating clock
> > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
> > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sdmmc0: can't enable card
> > sximmc0: timeout updating clock
> > boot device: lookup 'sd0a:/bsd' failed.
> > root on rd0a swap on rd0b dump on rd0b
> > WARNING: preposterous clock chip time
> > WARNING: CHECK AND RESET THE DATE!
> > erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> >
> > Welcome to the OpenBSD/armv7 6.1 installation program.
> > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
> > # date
> > Sat Apr 8 22:51:29 GMT 2017
> > # install
> > At any prompt except password prompts you can escape to a shell by
> > typing '!'. Default answers are shown in []'s and are selected by
> > pressing RETURN. You can exit this program at any time by pressing
> > Control-C, but this can leave your system in an inconsistent state.
> >
> > Terminal type? [vt220]
> > System hostname? (short form, e.g. 'foo') bananapro
> >
> > Available network interfaces are: dwge0.
> > Which network interface do you wish to configure? (or 'done') [dwge0]
> > IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
> > DHCPDISCOVER on dwge0 - interval 1
> > DHCPOFFER from 192.168.4.1 (45:c9:e3:9b:a3:54)
> > DHCPREQUEST on dwge0 to 255.255.255.255
> > DHCPACK from 192.168.4.1 (45:c9:e3:9b:a3:54)
> > bound to 192.168.4.10 -- renewal in 43199 seconds.
> > IPv6 address for dwge0? (or 'rtsol' or 'none') [none]
> > Available network interfaces are: dwge0.
> > Which network interface do you wish to configure? (or 'done') [done]
> > Using DNS domainname home.lan
> > Using DNS nameservers at 192.168.4.1 192.168.5.1
> >
> > Password for root account? (will not echo)
> > Password for root account? (again)
> > Start sshd(8) by default? [yes]
> > Setup a user? (enter a lower-case loginname, or 'no') [no]
> > Since no user was setup, root logins via sshd(8) might be useful.
> > WARNING: root is targeted by password guessing attacks, pubkeys are
> safer.
> > Allow root ssh login? (yes, no, prohibit-password) [no]
> > What timezone are you in? ('?' for list) [Europe/Belgrade]
> >
> > Available disks are: none.
> > Which disk is the root disk? ('?' for details) ?
> > Available disks are: none.
> > Which disk is the root disk? ('?' for details) Available disks are: none.
> > Which disk is the root disk? ('?' for details) ^C
> >
> > # dmesg
> > OpenBSD 6.1-current (RAMDISK) #84: Sat Apr 8 17:04:11 MDT 2017
> > dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> > real mem = 1072078848 (1022MB)
> > avail mem = 1037033472 (988MB)
> > mainbus0 at root: LeMaker Banana Pro
> > cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> > cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> > cortex0 at mainbus0
> > psci0 at mainbus0
> > agtimer0 at mainbus0: tick rate 24000 KHz
> > sxiccmu0 at mainbus0
> > simplebus0 at mainbus0: "soc"
> > sxipio0 at simplebus0: 175 pins
> > sximmc0 at simplebus0
> > sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> > sximmc1 at simplebus0
> > sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> > ehci0 at simplebus0
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> > 2.00/1.00 addr 1
> > sxiahci0 at simplebus0: AHCI 1.1
> > scsibus0 at sxiahci0: 32 targets
> > ehci1 at simplebus0
> > usb1 at ehci1: USB revision 2.0
> > uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> > 2.00/1.00 addr 1
> > sxidog0 at simplebus0
> > sxirtc0 at simplebus0
> > com0 at simplebus0: ns16550, no working fifo
> > com0: console
> > com1 at simplebus0: ns16550, no working fifo
> > com2 at simplebus0: ns16550, no working fifo
> > dwge0 at simplebus0
> > dwge0: Ethernet address: 02:17:04:40:c0:cc
> > rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> > ampintc0 at simplebus0 nirq 160, ncpu 2
> > gpio0 at sxipio0: 32 pins
> > gpio1 at sxipio0: 32 pins
> > gpio2 at sxipio0: 32 pins
> > gpio3 at sxipio0: 32 pins
> > gpio4 at sxipio0: 32 pins
> > gpio5 at sxipio0: 32 pins
> > gpio6 at sxipio0: 32 pins
> > gpio7 at sxipio0: 32 pins
> > gpio8 at sxipio0: 32 pins
> > sximmc0: timeout updating clock
> > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
> > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sximmc0: timeout updating clock
> > sdmmc0: can't enable card
> > sximmc0: timeout updating clock
> > boot device: lookup 'sd0a:/bsd' failed.
> > root on rd0a swap on rd0b dump on rd0b
> > WARNING: preposterous clock chip time
> > WARNING: CHECK AND RESET THE DATE!
> > # halt -p
> > syncing disks... done
> >
> > Attempting to power down...
> > The operating system has halted.
> > Please press any key to reboot.
> >
> >
> > [EOT]
> > $ ^D
> >
> > Script done on Sun Apr 9 12:54:36 2017
> >
> >
> > On Sun, Oct 30, 2016 at 10:00 AM, soko.tica <soko.t...@gmail.com> wrote:
> >
> >> Thank you for your input.
> >>
> >> For the record, FreeBSD 11.0-RC3 worked on each of these SD cards.
> >>
> >> In the case that it might obe of interest for anyone, i paste here a new
> >> typescript, starting from downloading and veryfing the images, preparing
> >> miniroot and starting the installation, which cannot recognize the sd
> card
> >> on which it is running, showing no available disks. That is why I tried
> to
> >> install from one SD card to another, thinking it is supposed to be so
> until
> >> I saw that usb stick recognizes itself as the target disk.
> >>
> >>
> >> =====
> >> Script started on Sun Oct 30 10:31:43 2016
> >> $ fdisk sd1
> >> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
> >> Offset: 0 Signature: 0xAA55
> >> Starting Ending LBA Info:
> >> #: id C H S - C H S [ start:
> size
> >> ]
> >> ------------------------------------------------------------
> >> -------------------
> >> *0: 0C 0 32 33 - 0 97 33 [ 2048: 4096 ]
> >> Win95 FAT32L
> >> 1: 00 0 0 0 - 0 0 0 [ 0: 0 ]
> unused
> >> 2: 00 0 0 0 - 0 0 0 [ 0: 0 ]
> unused
> >> 3: A6 0 97 34 - 2 75 9 [ 6144: 30720 ]
> >> OpenBSD
> >> $ doas fdisk -e sd1
> >> Enter 'help' for information
> >> fdisk: 1> p m
> >> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
> >> Offset: 0 Signature: 0xAA55
> >> Starting Ending LBA Info:
> >> #: id C H S - C H S [ start:
> size
> >> ]
> >> ------------------------------------------------------------
> >> -------------------
> >> *0: 0C 0 32 33 - 0 97 33 [ 2048: 2M]
> Win95
> >> FAT32L
> >> 1: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> 2: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> 3: A6 0 97 34 - 2 75 9 [ 6144: 15M]
> >> OpenBSD
> >> fdisk: 1> e 0
> >> Starting Ending LBA Info:
> >> #: id C H S - C H S [ start:
> size
> >> ]
> >> ------------------------------------------------------------
> >> -------------------
> >> *0: 0C 0 32 33 - 0 97 33 [ 2048: 4096 ]
> >> Win95 FAT32L
> >> Partition id ('0' to disable) [01 - FF]: [C] (? for help) 0
> >> Partition 0 is disabled.
> >> fdisk:*1> e 3
> >> Starting Ending LBA Info:
> >> #: id C H S - C H S [ start:
> size
> >> ]
> >> ------------------------------------------------------------
> >> -------------------
> >> 3: A6 0 97 34 - 2 75 9 [ 6144: 30720 ]
> >> OpenBSD
> >> Partition id ('0' to disable) [01 - FF]: [A6] (? for help) 0
> >> Partition 3 is disabled.
> >> fdisk:*1> p m
> >> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
> >> Offset: 0 Signature: 0xAA55
> >> Starting Ending LBA Info:
> >> #: id C H S - C H S [ start:
> size
> >> ]
> >> ------------------------------------------------------------
> >> -------------------
> >> 0: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> 1: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> 2: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> 3: 00 0 0 0 - 0 0 0 [ 0: 0M]
> unused
> >> fdisk:*1> w
> >> Writing MBR at offset 0.
> >> fdisk: 1> q
> >> $ disklabel sd1
> >> # /dev/rsd1c:
> >> type: SCSI
> >> disk: SCSI disk
> >> label: Storage Device
> >> duid: 0000000000000000
> >> flags:
> >> bytes/sector: 512
> >> sectors/track: 63
> >> tracks/cylinder: 255
> >> sectors/cylinder: 16065
> >> cylinders: 1887
> >> total sectors: 30318592
> >> boundstart: 0
> >> boundend: 30318592
> >> drivedata: 0
> >>
> >> 16 partitions:
> >> # size offset fstype [fsize bsize cpg]
> >> c: 30318592 0 unused
> >> $ pwd
> >> /home/doasuser
> >> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/SHA256.sig
> >> Trying 91.185.196.203...
> >> Connected to ftp.obsd.si.
> >> 220 nina.kerberos.si FTP server ready.
> >> 331 Guest login ok, send your email address as password.
> >> 230 Guest login ok, access restrictions apply.
> >> Remote system type is UNIX.
> >> Using binary mode to transfer files.
> >> 200 Type set to I.
> >> 250 CWD command successful.
> >> Retrieving pub/OpenBSD/snapshots/armv7/SHA256.sig
> >> local: SHA256.sig remote: SHA256.sig
> >> 150 Opening BINARY mode data connection for 'SHA256.sig' (1978 bytes).
> >> 100% |**************************************************| 1978
> >> 00:00 ETA
> >> 226 Transfer complete.
> >> 1978 bytes received in 0.20 seconds (9.45 KB/s)
> >> 221 Goodbye.
> >> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/SHA256.sig
> >> Trying 91.185.196.203...
> >> Connected to ftp.obsd.si.
> >> 220 nina.kerberos.si FTP server ready.
> >> 331 Guest login ok, send your email address as password.
> >> 230 Guest login ok, access restrictions apply.
> >> Remote system type is UNIX.
> >> Using binary mode to transfer files.
> >> 200 Type set to I.
> >> 250 CWD command successful.
> >> Retrieving pub/OpenBSD/snapshots/armv7/SHA256
> >> local: SHA256 remote: SHA256
> >> 150 Opening BINARY mode data connection for 'SHA256' (1815 bytes).
> >> 100% |**************************************************| 1815
> >> 00:00 ETA
> >> 226 Transfer complete.
> >> 1815 bytes received in 0.21 seconds (8.32 KB/s)
> >> 221 Goodbye.
> >> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/miniroot-
> cubie-60.fs
> >> Trying 91.185.196.203...
> >> Connected to ftp.obsd.si.
> >> 220 nina.kerberos.si FTP server ready.
> >> 331 Guest login ok, send your email address as password.
> >> 230 Guest login ok, access restrictions apply.
> >> Remote system type is UNIX.
> >> Using binary mode to transfer files.
> >> 200 Type set to I.
> >> 250 CWD command successful.
> >> Retrieving pub/OpenBSD/snapshots/armv7/miniroot-cubie-60.fs
> >> local: miniroot-cubie-60.fs remote: miniroot-cubie-60.fs
> >> 150 Opening BINARY mode data connection for 'miniroot-cubie-60.fs'
> >> (18874368 bytes).
> >> 100% |**************************************************| 18432 KB
> >> 00:18 ETA
> >> 226 Transfer complete.
> >> 18874368 bytes received in 18.17 seconds (1014.66 KB/s)
> >> 221 Goodbye.
> >> $ sha256 -c SHA256
> >> sha256: cannot open BOOTARM.EFI: No such file or directory
> >> (SHA256) BOOTARM.EFI: MISSING
> >> sha256: cannot open BUILDINFO: No such file or directory
> >> (SHA256) BUILDINFO: MISSING
> >> sha256: cannot open INSTALL.armv7: No such file or directory
> >> (SHA256) INSTALL.armv7: MISSING
> >> sha256: cannot open base60.tgz: No such file or directory
> >> (SHA256) base60.tgz: MISSING
> >> sha256: cannot open bsd: No such file or directory
> >> (SHA256) bsd: MISSING
> >> sha256: cannot open bsd.rd: No such file or directory
> >> (SHA256) bsd.rd: MISSING
> >> sha256: cannot open comp60.tgz: No such file or directory
> >> (SHA256) comp60.tgz: MISSING
> >> sha256: cannot open game60.tgz: No such file or directory
> >> (SHA256) game60.tgz: MISSING
> >> sha256: cannot open man60.tgz: No such file or directory
> >> (SHA256) man60.tgz: MISSING
> >> sha256: cannot open miniroot-am335x-60.fs: No such file or directory
> >> (SHA256) miniroot-am335x-60.fs: MISSING
> >> sha256: cannot open miniroot-beagle-60.fs: No such file or directory
> >> (SHA256) miniroot-beagle-60.fs: MISSING
> >> (SHA256) miniroot-cubie-60.fs: OK
> >> sha256: cannot open miniroot-cubox-60.fs: No such file or directory
> >> (SHA256) miniroot-cubox-60.fs: MISSING
> >> sha256: cannot open miniroot-nitrogen-60.fs: No such file or directory
> >> (SHA256) miniroot-nitrogen-60.fs: MISSING
> >> sha256: cannot open miniroot-panda-60.fs: No such file or directory
> >> (SHA256) miniroot-panda-60.fs: MISSING
> >> sha256: cannot open miniroot-wandboard-60.fs: No such file or directory
> >> (SHA256) miniroot-wandboard-60.fs: MISSING
> >> sha256: cannot open xbase60.tgz: No such file or directory
> >> (SHA256) xbase60.tgz: MISSING
> >> sha256: cannot open xfont60.tgz: No such file or directory
> >> (SHA256) xfont60.tgz: MISSING
> >> sha256: cannot open xserv60.tgz: No such file or directory
> >> (SHA256) xserv60.tgz: MISSING
> >> sha256: cannot open xshare60.tgz: No such file or directory
> >> (SHA256) xshare60.tgz: MISSING
> >> $ sha256 -c SHA256 | grep 'OK'
> >> sha256: cannot open BOOTARM.EFI: No such file or directory
> >> sha256: cannot open BUILDINFO: No such file or directory
> >> sha256: cannot open INSTALL.armv7: No such file or directory
> >> sha256: cannot open base60.tgz: No such file or directory
> >> sha256: cannot open bsd: No such file or directory
> >> sha256: cannot open bsd.rd: No such file or directory
> >> sha256: cannot open comp60.tgz: No such file or directory
> >> sha256: cannot open game60.tgz: No such file or directory
> >> sha256: cannot open man60.tgz: No such file or directory
> >> sha256: cannot open miniroot-am335x-60.fs: No such file or directory
> >> sha256: cannot open miniroot-beagle-60.fs: No such file or directory
> >> sha256: cannot open miniroot-cubox-60.fs: No such file or directory
> >> sha256: cannot open miniroot-nitrogen-60.fs: No such file or directory
> >> sha256: cannot open miniroot-panda-60.fs: No such file or directory
> >> sha256: cannot open miniroot-wandboard-60.fs: No such file or directory
> >> sha256: cannot open xbase60.tgz: No such file or directory
> >> sha256: cannot open xfont60.tgz: No such file or directory
> >> sha256: cannot open xserv60.tgz: No such file or directory
> >> sha256: cannot open xshare60.tgz: No such file or directory
> >> (SHA256) miniroot-cubie-60.fs: OK
> >> gnify/openbsd-60-base.pub.-xbSHA256.sig.siSH <
> >> Signature Verified
> >> miniroot-cubie-60.fs: OK
> >> BOOTARM.EFI: FAIL
> >> miniroot-beagle-60.fs: FAIL
> >> bsd: FAIL
> >> bsd.rd: FAIL
> >> miniroot-cubox-60.fs: FAIL
> >> game60.tgz: FAIL
> >> comp60.tgz: FAIL
> >> miniroot-nitrogen-60.fs: FAIL
> >> xserv60.tgz: FAIL
> >> miniroot-am335x-60.fs: FAIL
> >> xshare60.tgz: FAIL
> >> xbase60.tgz: FAIL
> >> base60.tgz: FAIL
> >> miniroot-panda-60.fs: FAIL
> >> xfont60.tgz: FAIL
> >> man60.tgz: FAIL
> >> BUILDINFO: FAIL
> >> miniroot-wandboard-60.fs: FAIL
> >> INSTALL.armv7: FAIL
> >> $ signify -C -p /etc/signify/openbsd-60-base.pub -x SHA256.sig | grep
> 'OK'
> >> miniroot-cubie-60.fs: OK
> >> BOOTARM.EFI: FAIL
> >> miniroot-beagle-60.fs: FAIL
> >> bsd: FAIL
> >> bsd.rd: FAIL
> >> miniroot-cubox-60.fs: FAIL
> >> game60.tgz: FAIL
> >> comp60.tgz: FAIL
> >> miniroot-nitrogen-60.fs: FAIL
> >> xserv60.tgz: FAIL
> >> miniroot-am335x-60.fs: FAIL
> >> xshare60.tgz: FAIL
> >> xbase60.tgz: FAIL
> >> base60.tgz: FAIL
> >> miniroot-panda-60.fs: FAIL
> >> xfont60.tgz: FAIL
> >> man60.tgz: FAIL
> >> BUILDINFO: FAIL
> >> miniroot-wandboard-60.fs: FAIL
> >> INSTALL.armv7: FAIL
> >> oasovnconfigfvnd0nminiroot-cubie-60.fs <
> >> $ doas dd if=/usr/local/share/u-boot/AananaPr
> >> A10-OLinuXino-Lime/ A20-OLinuXino-Lime/ A20-OLinuXino_MICRO/
> >> A10s-OLinuXino-M/ A20-OLinuXino-Lime2/
> >> ot/Bananapro/u-boot-sunxi-with-spl.binaof=/dev/rvnd0c-bs=1024 seek=8
> >> <
> >> 476+1 records in
> >> 476+1 records out
> >> 488235 bytes transferred in 0.034 secs (14271287 bytes/sec)
> >> $ disklabel vnd0
> >> disklabel: ioctl DIOCGDINFO: Operation not permitted
> >> $ doas disklabel vnd0
> >> # /dev/rvnd0c:
> >> type: vnd
> >> disk: vnd device
> >> label: fictitious
> >> duid: b7b29d6a08b186c2
> >> flags:
> >> bytes/sector: 512
> >> sectors/track: 256
> >> tracks/cylinder: 16
> >> sectors/cylinder: 4096
> >> cylinders: 9
> >> total sectors: 36864
> >> boundstart: 6144
> >> boundend: 36864
> >> drivedata: 0
> >>
> >> 16 partitions:
> >> # size offset fstype [fsize bsize cpg]
> >> a: 30720 6144 4.2BSD 2048 16384 240
> >> c: 36864 0 unused
> >> i: 4096 2048 MSDOS
> >> $ doas mount /dev/vnd0i /mnt/usb
> >> $ ls -lh /mnt/usb
> >> total 80
> >> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
> >> -rw-r--r-- 1 root wheel 33.4K Oct 30 01:32 sun7i-a20-cubieboard2.dtb
> >> $rmo/mnt/usb/sun7i-a20-cubieboard2.dtb <
> >> $ lsa-lhm/mnt/usbb/sun7i-a20-cubieboard2.dtb
> >> total 8
> >> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
> >> $ doas cp /usr/local/share/dtb/arm
> >> arm/ arm64/
> >> tb/arm/sun7i-a20-bananapro.dtbd/mnt/usbusn20-bananapr
> <
> >> $ lsa-lhp/mnt/usbcal/share/dtb/arm/sun7i-a20-bananapro.dtb /mnt/usb
> >> total 80
> >> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
> >> -rw-r--r-- 1 root wheel 33.6K Oct 30 10:37 sun7i-a20-bananapro.dtb
> >> $ doas umount /mnt/usb
> >> $ doas vnconfig -u vnd0
> >> $ ls -lh
> >> total 36948
> >> -rw-r--r-- 1 doasuser doasuser 1.8K Oct 30 05:21 SHA256
> >> -rw-r--r-- 1 doasuser doasuser 1.9K Oct 30 05:21 SHA256.sig
> >> -rw-r--r-- 1 doasuser doasuser 18.0M Oct 30 10:37
> miniroot-cubie-60.fs
> >> -rw-r--r-- 1 doasuser doasuser 20.8K Oct 30 10:39 typescript
> >> $ doas if=miniroot-cubie-60.fs of=/dev/rsd1c bs=1024
> >> doas: if=miniroot-cubie-60.fs: command not found
> >> $ doas ddiif=miniroot-cubie-60.fsoof=/dev/rsd1cbbs=1024
> >> 18432+0 records in
> >> 18432+0 records out
> >> 18874368 bytes transferred in 15.508 secs (1217046 bytes/sec)
> >> $ cu -l cuaU0 -s 115200
> >> cu: open("/dev/cuaU0"): Permission denied
> >> $ whoami
> >> doasuser
> >> $ doas cu -l cuaU0 -s 115200
> >> Connected to /dev/cuaU0 (speed 115200)
> >>
> >> U-Boot SPL 2016.09 (Sep 20 2016 - 02:39:19)
> >> DRAM: 1024 MiB
> >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> >> Trying to boot from MMC1
> >>
> >>
> >>
> >> U-Boot 2016.09 (Sep 20 2016 - 02:39:19 -0600) Allwinner Technology
> >>
> >> CPU: Allwinner A20 (SUN7I)
> >> Model: LeMaker Banana Pro
> >> I2C: ready
> >> DRAM: 1 GiB
> >> MMC: SUNXI SD/MMC: 0
> >> *** Warning - bad CRC, using default environment
> >>
> >> Setting up a 720x576i composite-pal console (overscan 32x20)
> >> In: serial
> >> Out: vga
> >> Err: vga
> >> SCSI: SATA link 0 timeout.
> >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> >> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> >> Net: eth0: ethernet@01c50000
> >> starting USB...
> >> USB0: USB EHCI 1.00
> >> USB1: USB OHCI 1.0
> >> USB2: USB EHCI 1.00
> >> USB3: USB OHCI 1.0
> >> scanning bus 0 for devices... 1 USB Device(s) found
> >> scanning bus 2 for devices... 1 USB Device(s) found
> >> Hit any key to stop autoboot: 0
> >> switch to partitions #0, OK
> >> mmc0 is current device
> >> Scanning mmc 0:1...
> >> reading /sun7i-a20-bananapro.dtb
> >> 34451 bytes read in 29 ms (1.1 MiB/s)
> >> Found EFI removable media binary efi/boot/bootarm.efi
> >> reading efi/boot/bootarm.efi
> >> 64684 bytes read in 40 ms (1.5 MiB/s)
> >> ## Starting EFI application at 0x42000000 ...
> >> CACHE: Misaligned operation at range [79f1d000, 79f2ccac]
> >> Scanning disks on scsi...
> >> Scanning disks on usb...
> >> Scanning disks on mmc...
> >> MMC Device 1 not found
> >> MMC Device 2 not found
> >> MMC Device 3 not found
> >> Found 6 disks
> >>>> OpenBSD/armv7 BOOTARM 0.5
> >> boot>
> >> cannot open sd0a:/etc/random.seed: No such file or directory
> >> booting sd0a:/bsd: 2138360+7972148+442776 [80+310912+150523]=0xa87334
> >>
> >> OpenBSD/armv7 booting ...
> >> arg0 0xc0d87334 arg1 0x0 arg2 0x48000000
> >> Allocating page tables
> >> freestart = 0x40d88000, free_pages = 258274 (0x0003f0e2)
> >> IRQ stack: p0x40db6000 v0xc0db6000
> >> ABT stack: p0x40db7000 v0xc0db7000
> >> UND stack: p0x40db8000 v0xc0db8000
> >> SVC stack: p0x40db9000 v0xc0db9000
> >> Creating L1 page table at 0x40d88000
> >> Mapping kernel
> >> Constructing L2 page tables
> >> undefined page pmap board type: 0
> >> Copyright (c) 1982, 1986, 1989, 1991, 1993
> >> The Regents of the University of California. All rights reserved.
> >> Copyright (c) 1995-2016 OpenBSD. All rights reserved.
> >> https://www.OpenBSD.org
> >>
> >> OpenBSD 6.0-current (RAMDISK) #0: Sat Oct 29 17:32:38 MDT 2016
> >> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> >> real mem = 1072078848 (1022MB)
> >> avail mem = 1037021184 (988MB)
> >>
> >> mainbus0 at root: LeMaker Banana Pro
> >> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> >> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> >> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> >> cortex0 at mainbus0
> >> agtimer0 at mainbus0: tick rate 24000 KHz
> >> sxiccmu0 at mainbus0
> >> simplebus0 at mainbus0: "soc"
> >> sxipio0 at simplebus0: 175 pins
> >> sximmc0 at simplebus0
> >> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> >> sximmc1 at simplebus0
> >> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> >> ehci0 at simplebus0
> >> usb0 at ehci0: USB revision 2.0
> >> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> >> 2.00/1.00 addr 1
> >> sxiahci0 at simplebus0: AHCI 1.1
> >> scsibus0 at sxiahci0: 32 targets
> >> ehci1 at simplebus0
> >> usb1 at ehci1: USB revision 2.0
> >> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> >> 2.00/1.00 addr 1
> >> sxidog0 at simplebus0
> >> sxirtc0 at simplebus0
> >> com0 at simplebus0: ns16550, no working fifo
> >> com0: console
> >> com1 at simplebus0: ns16550, no working fifo
> >> com2 at simplebus0: ns16550, no working fifo
> >> dwge0 at simplebus0
> >> dwge0: Ethernet address: 02:17:04:40:c0:cc
> >> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> >> ampintc0 at simplebus0 nirq 160
> >> gpio0 at sxipio0: 18 pins
> >> gpio1 at sxipio0: 24 pins
> >> gpio2 at sxipio0: 25 pins
> >> gpio3 at sxipio0: 28 pins
> >> gpio4 at sxipio0: 12 pins
> >> gpio5 at sxipio0: 6 pins
> >> gpio6 at sxipio0: 12 pins
> >> gpio7 at sxipio0: 28 pins
> >> gpio8 at sxipio0: 22 pins
> >> sximmc0: timeout updating clock
> >> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
> >> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
> >> sximmc0: timeout updating clock
> >> sximmc0: timeout updating clock
> >> sximmc0: timeout updating clock
> >> sximmc0: timeout updating clock
> >> sximmc0: timeout updating clock
> >> sdmmc0: can't enable card
> >> sximmc0: timeout updating clock
> >> boot device: lookup 'sd0a:/bsd' failed.
> >> root on rd0a swap on rd0b dump on rd0b
> >> WARNING: clock lost 17103 days
> >> WARNING: CHECK AND RESET THE DATE!
> >> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> >>
> >> Welcome to the OpenBSD/armv7 6.0 installation program.
> >> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
> >> At any prompt except password prompts you can escape to a shell by
> >> typing '!'. Default answers are shown in []'s and are selected by
> >> pressing RETURN. You can exit this program at any time by pressing
> >> Control-C, but this can leave your system in an inconsistent state.
> >>
> >> Terminal type? [vt220]
> >> System hostname? (short form, e.g. 'foo') banana
> >>
> >> Available network interfaces are: dwge0.
> >> Which network interface do you wish to configure? (or 'done') [dwge0]
> >> IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
> >> DHCPDISCOVER on dwge0 - interval 1
> >> DHCPOFFER from 192.168.1.1 (a4:79:47:e5:05:32)
> >> DHCPREQUEST on dwge0 to 255.255.255.255
> >> DHCPACK from 192.168.1.1 (a4:79:47:e5:05:32)
> >> bound to 192.168.1.2 -- renewal in 43200 seconds.
> >> IPv6 address for dwge0? (or 'rtsol' or 'none') [none]
> >> Available network interfaces are: dwge0.
> >> Which network interface do you wish to configure? (or 'done') [done]
> >> Using DNS domainname my.domain
> >> Using DNS nameservers at 192.168.1.1 192.168.1.1
> >>
> >> Password for root account? (will not echo)
> >> Password for root account? (again)
> >> Start sshd(8) by default? [yes]
> >> Setup a user? (enter a lower-case loginname, or 'no') [no]
> >> Since no user was setup, root logins via sshd(8) might be useful.
> >> WARNING: root is targeted by password guessing attacks, pubkeys are
> safer.
> >> Allow root ssh login? (yes, no, prohibit-password) [no]
> >> What timezone are you in? ('?' for list) [Europe/Belgrade]
> >>
> >> Available disks are: none.
> >> Which disk is the root disk? ('?' for details) ?
> >> Available disks are: none.
> >> Which disk is the root disk? ('?' for details) ^C
> >>
> >> # halt
> >> syncing disks... done
> >> The operating system has halted.
> >> Please press any key to reboot.
> >>
> >> Killed
> >> $ exit
> >>
> >> Script done on Sun Oct 30 10:46:35 2016
> >>
> >> ===
> >>
> >> On Sun, Oct 30, 2016 at 8:21 AM, Jonathan Gray <j...@jsg.id.au> wrote:
> >>
> >>> ommmc is for omap not sunxi. sximmc is the sunxi equivalent.
> >>>
> >>> sximmc0: timeout updating clock
> >>> sximmc0: timeout updating clock
> >>> sximmc0: timeout updating clock
> >>> sximmc0: timeout updating clock
> >>> sximmc0: timeout updating clock
> >>> sximmc0: timeout updating clock
> >>> sdmmc0: can't enable card
> >>> sximmc0: timeout updating clock
> >>>
> >>> If the cause of that were found and fixed, sd0 would attach.
> >>> sximmc works on other a20 based systems, it isn't clear what
> >>> makes this one different besides having multiple sximmc devices.
> >>>
> >>> On Sun, Oct 30, 2016 at 08:09:24AM +0100, soko.tica wrote:
> >>>> It seems that "the mistery" is solved - OpenBSD doesn't have support
> for
> >>>> ommc http://man.openbsd.org/OpenBSD-current/man4/armv7/ommmc.4 on
> sunxi
> >>>> https://www.openbsd.org/armv7.html
> >>>>
> >>>> Once the miniroot is written to usb stick it is able to install on the
> >>> same
> >>>> usb stick.
> >>>>
> >>>> In the case I am still wrong about this, don't be shy to write it
> here,
> >>>> someone might read it in future.
> >>>>
> >>>> Regards,
> >>>>
> >>>> Soko Tica
> >>>>
> >>>> On Sat, Oct 29, 2016 at 10:19 PM, soko.tica <soko.t...@gmail.com>
> >>> wrote:
> >>>>> Hello,
> >>>>>
> >>>>> I have managed to successfully install -current on BananaPro
> >>> (allegedly
> >>>>> the same board as BananaPi plus wi-fi), but the boot can't be
> >>> completed
> >>>>> because
> >>>>> "boot device: lookup 'sd0a:/bsd' failed"
> >>>>> although it was initially found (as shown in the typescript bellow).
> >>>>>
> >>>>> I performed the install(s) from a SD card plugged into micro card
> >>> slot to
> >>>>> another SD card plugged into usb card reader. I did edit partition
> >>> sizes
> >>>>> suggested by autopartition. Upon completing the install I place the
> >>> target
> >>>>> SD card into the micro card slot and try to boot.
> >>>>>
> >>>>> Please advise if I am missing something obvious.
> >>>>>
> >>>>> Output of the typescript
> >>>>> ========================
> >>>>> U-Boot 2016.09 (Sep 20 2016 - 02:39:19 -0600) Allwinner Technology
> >>>>>
> >>>>> CPU: Allwinner A20 (SUN7I)
> >>>>> Model: LeMaker Banana Pro
> >>>>> I2C: ready
> >>>>> DRAM: 1 GiB
> >>>>> MMC: SUNXI SD/MMC: 0
> >>>>> *** Warning - bad CRC, using default environment
> >>>>>
> >>>>> Setting up a 720x576i composite-pal console (overscan 32x20)
> >>>>> In: serial
> >>>>> Out: vga
> >>>>> Err: vga
> >>>>> SCSI: SATA link 0 timeout.
> >>>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> >>>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> >>>>> Net: eth0: ethernet@01c50000
> >>>>> starting USB...
> >>>>> USB0: USB EHCI 1.00
> >>>>> USB1: USB OHCI 1.0
> >>>>> USB2: USB EHCI 1.00
> >>>>> USB3: USB OHCI 1.0
> >>>>> scanning bus 0 for devices... 1 USB Device(s) found
> >>>>> scanning bus 2 for devices... 1 USB Device(s) found
> >>>>> Hit any key to stop autoboot: 0
> >>>>> switch to partitions #0, OK
> >>>>> mmc0 is current device
> >>>>> Scanning mmc 0:1...
> >>>>> reading /sun7i-a20-bananapro.dtb
> >>>>> 31159 bytes read in 30 ms (1013.7 KiB/s)
> >>>>> Found EFI removable media binary efi/boot/bootarm.efi
> >>>>> reading efi/boot/bootarm.efi
> >>>>> 64684 bytes read in 41 ms (1.5 MiB/s)
> >>>>> ## Starting EFI application at 0x42000000 ...
> >>>>> CACHE: Misaligned operation at range [79f1d000, 79f2ccac]
> >>>>> Scanning disks on scsi...
> >>>>> Scanning disks on usb...
> >>>>> Scanning disks on mmc...
> >>>>> MMC Device 1 not found
> >>>>> MMC Device 2 not found
> >>>>> MMC Device 3 not found
> >>>>> Found 6 disks
> >>>>>>> OpenBSD/armv7 BOOTARM 0.5
> >>>>> boot>
> >>>>> cannot open sd0a:/etc/random.seed: No such file or directory
> >>>>> booting sd0a:/bsd: 2138412+7972140+442552 [80+310912+150523]=0xa8724c
> >>>>>
> >>>>> OpenBSD/armv7 booting ...
> >>>>> arg0 0xc0d8724c arg1 0x0 arg2 0x48000000
> >>>>> Allocating page tables
> >>>>> freestart = 0x40d88000, free_pages = 258274 (0x0003f0e2)
> >>>>> IRQ stack: p0x40db6000 v0xc0db6000
> >>>>> ABT stack: p0x40db7000 v0xc0db7000
> >>>>> UND stack: p0x40db8000 v0xc0db8000
> >>>>> SVC stack: p0x40db9000 v0xc0db9000
> >>>>> Creating L1 page table at 0x40d88000
> >>>>> Mapping kernel
> >>>>> Constructing L2 page tables
> >>>>> undefined page pmap board type: 0
> >>>>> Copyright (c) 1982, 1986, 1989, 1991, 1993
> >>>>> The Regents of the University of California. All rights
> reserved.
> >>>>> Copyright (c) 1995-2016 OpenBSD. All rights reserved.
> >>>>> https://www.OpenBSD.org
> >>>>>
> >>>>> OpenBSD 6.0-current (RAMDISK) #0: Tue Oct 25 02:52:36 MDT 2016
> >>>>> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/
> compile/RAMDISK
> >>>>> real mem = 1072078848 (1022MB)
> >>>>> avail mem = 1037025280 (988MB)
> >>>>> mainbus0 at root: LeMaker Banana Pro
> >>>>> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> >>>>> cpu0: DC enabled IC enabled WB disabled EABT branch prediction
> enabled
> >>>>> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> >>>>> cortex0 at mainbus0
> >>>>> agtimer0 at mainbus0: tick rate 24000 KHz
> >>>>> sxiccmu0 at mainbus0
> >>>>> simplebus0 at mainbus0: "soc"
> >>>>> sxipio0 at simplebus0: 175 pins
> >>>>> sximmc0 at simplebus0
> >>>>> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> >>>>> sximmc1 at simplebus0
> >>>>> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> >>>>> ehci0 at simplebus0
> >>>>> usb0 at ehci0: USB revision 2.0
> >>>>> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub"
> >>> rev
> >>>>> 2.00/1.00 addr 1
> >>>>> sxiahci0 at simplebus0: AHCI 1.1
> >>>>> scsibus0 at sxiahci0: 32 targets
> >>>>> ehci1 at simplebus0
> >>>>> usb1 at ehci1: USB revision 2.0
> >>>>> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub"
> >>> rev
> >>>>> 2.00/1.00 addr 1
> >>>>> sxidog0 at simplebus0
> >>>>> sxirtc0 at simplebus0
> >>>>> com0 at simplebus0: ns16550, no working fifo
> >>>>> com0: console
> >>>>> com1 at simplebus0: ns16550, no working fifo
> >>>>> com2 at simplebus0: ns16550, no working fifo
> >>>>> dwge0 at simplebus0
> >>>>> dwge0: Ethernet address: 02:17:04:40:c0:cc
> >>>>> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> >>>>> ampintc0 at simplebus0 nirq 160
> >>>>> gpio0 at sxipio0: 18 pins
> >>>>> gpio1 at sxipio0: 24 pins
> >>>>> gpio2 at sxipio0: 25 pins
> >>>>> gpio3 at sxipio0: 28 pins
> >>>>> gpio4 at sxipio0: 12 pins
> >>>>> gpio5 at sxipio0: 6 pins
> >>>>> gpio6 at sxipio0: 12 pins
> >>>>> gpio7 at sxipio0: 28 pins
> >>>>> gpio8 at sxipio0: 22 pins
> >>>>> sximmc0: timeout updating clock
> >>>>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not
> >>> configured
> >>>>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not
> >>> configured
> >>>>> sximmc0: timeout updating clock
> >>>>> sximmc0: timeout updating clock
> >>>>> sximmc0: timeout updating clock
> >>>>> sximmc0: timeout updating clock
> >>>>> sximmc0: timeout updating clock
> >>>>> sdmmc0: can't enable card
> >>>>> sximmc0: timeout updating clock
> >>>>> boot device: lookup 'sd0a:/bsd' failed.
> >>>>> root on rd0a swap on rd0b dump on rd0b
> >>>>> WARNING: clock lost 17099 days
> >>>>> WARNING: CHECK AND RESET THE DATE!
> >>>>> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> >>>>>
> >>>>> ===========================
> >>>>>
> >>>>> Several times I also tried with interrupting the boot and
> >>>>>
> >>>>> => run findfdt
> >>>>> => load mmc 0:1 ${fdt_addr_r} ${fdtfile}
> >>>>> => load mmc 0:1 ${kernel_addr_r} efi/boot/bootarm.efi
> >>>>> => bootefi ${kernel_addr_r} ${fdt_addr_r}
> >>>>>
> >>>>> as per the instructions ftp://ftp.obsd.si/pub/OpenBSD/
> >>>>> snapshots/armv7/INSTALL.armv7
> >>>>>
> >>>>> But with the same result.
> >>>>>
> >>>>> Thanks in advance,
> >>>>>
> >>>>> Regards,
> >>>>>
> >>>>> Soko Tica
> >>>>>
> >>
> >
>
>
>
