It seems that "the mistery" is solved - OpenBSD doesn't have support for ommc http://man.openbsd.org/OpenBSD-current/man4/armv7/ommmc.4 on sunxi https://www.openbsd.org/armv7.html
Once the miniroot is written to usb stick it is able to install on the same usb stick. In the case I am still wrong about this, don't be shy to write it here, someone might read it in future. Regards, Soko Tica On Sat, Oct 29, 2016 at 10:19 PM, soko.tica <soko.t...@gmail.com> wrote: > Hello, > > I have managed to successfully install -current on BananaPro (allegedly > the same board as BananaPi plus wi-fi), but the boot can't be completed > because > "boot device: lookup 'sd0a:/bsd' failed" > although it was initially found (as shown in the typescript bellow). > > I performed the install(s) from a SD card plugged into micro card slot to > another SD card plugged into usb card reader. I did edit partition sizes > suggested by autopartition. Upon completing the install I place the target > SD card into the micro card slot and try to boot. > > Please advise if I am missing something obvious. > > Output of the typescript > ======================== > U-Boot 2016.09 (Sep 20 2016 - 02:39:19 -0600) Allwinner Technology > > CPU: Allwinner A20 (SUN7I) > Model: LeMaker Banana Pro > I2C: ready > DRAM: 1 GiB > MMC: SUNXI SD/MMC: 0 > *** Warning - bad CRC, using default environment > > Setting up a 720x576i composite-pal console (overscan 32x20) > In: serial > Out: vga > Err: vga > SCSI: SATA link 0 timeout. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > Net: eth0: ethernet@01c50000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB OHCI 1.0 > USB2: USB EHCI 1.00 > USB3: USB OHCI 1.0 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 2 for devices... 1 USB Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > reading /sun7i-a20-bananapro.dtb > 31159 bytes read in 30 ms (1013.7 KiB/s) > Found EFI removable media binary efi/boot/bootarm.efi > reading efi/boot/bootarm.efi > 64684 bytes read in 41 ms (1.5 MiB/s) > ## Starting EFI application at 0x42000000 ... > CACHE: Misaligned operation at range [79f1d000, 79f2ccac] > Scanning disks on scsi... > Scanning disks on usb... > Scanning disks on mmc... > MMC Device 1 not found > MMC Device 2 not found > MMC Device 3 not found > Found 6 disks > >> OpenBSD/armv7 BOOTARM 0.5 > boot> > cannot open sd0a:/etc/random.seed: No such file or directory > booting sd0a:/bsd: 2138412+7972140+442552 [80+310912+150523]=0xa8724c > > OpenBSD/armv7 booting ... > arg0 0xc0d8724c arg1 0x0 arg2 0x48000000 > Allocating page tables > freestart = 0x40d88000, free_pages = 258274 (0x0003f0e2) > IRQ stack: p0x40db6000 v0xc0db6000 > ABT stack: p0x40db7000 v0xc0db7000 > UND stack: p0x40db8000 v0xc0db8000 > SVC stack: p0x40db9000 v0xc0db9000 > Creating L1 page table at 0x40d88000 > Mapping kernel > Constructing L2 page tables > undefined page pmap board type: 0 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2016 OpenBSD. All rights reserved. > https://www.OpenBSD.org > > OpenBSD 6.0-current (RAMDISK) #0: Tue Oct 25 02:52:36 MDT 2016 > dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK > real mem = 1072078848 (1022MB) > avail mem = 1037025280 (988MB) > mainbus0 at root: LeMaker Banana Pro > cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core) > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache > cortex0 at mainbus0 > agtimer0 at mainbus0: tick rate 24000 KHz > sxiccmu0 at mainbus0 > simplebus0 at mainbus0: "soc" > sxipio0 at simplebus0: 175 pins > sximmc0 at simplebus0 > sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma > sximmc1 at simplebus0 > sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma > ehci0 at simplebus0 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev > 2.00/1.00 addr 1 > sxiahci0 at simplebus0: AHCI 1.1 > scsibus0 at sxiahci0: 32 targets > ehci1 at simplebus0 > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev > 2.00/1.00 addr 1 > sxidog0 at simplebus0 > sxirtc0 at simplebus0 > com0 at simplebus0: ns16550, no working fifo > com0: console > com1 at simplebus0: ns16550, no working fifo > com2 at simplebus0: ns16550, no working fifo > dwge0 at simplebus0 > dwge0: Ethernet address: 02:17:04:40:c0:cc > rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 > ampintc0 at simplebus0 nirq 160 > gpio0 at sxipio0: 18 pins > gpio1 at sxipio0: 24 pins > gpio2 at sxipio0: 25 pins > gpio3 at sxipio0: 28 pins > gpio4 at sxipio0: 12 pins > gpio5 at sxipio0: 6 pins > gpio6 at sxipio0: 12 pins > gpio7 at sxipio0: 28 pins > gpio8 at sxipio0: 22 pins > sximmc0: timeout updating clock > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured > (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured > sximmc0: timeout updating clock > sximmc0: timeout updating clock > sximmc0: timeout updating clock > sximmc0: timeout updating clock > sximmc0: timeout updating clock > sdmmc0: can't enable card > sximmc0: timeout updating clock > boot device: lookup 'sd0a:/bsd' failed. > root on rd0a swap on rd0b dump on rd0b > WARNING: clock lost 17099 days > WARNING: CHECK AND RESET THE DATE! > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > =========================== > > Several times I also tried with interrupting the boot and > > => run findfdt > => load mmc 0:1 ${fdt_addr_r} ${fdtfile} > => load mmc 0:1 ${kernel_addr_r} efi/boot/bootarm.efi > => bootefi ${kernel_addr_r} ${fdt_addr_r} > > as per the instructions ftp://ftp.obsd.si/pub/OpenBSD/ > snapshots/armv7/INSTALL.armv7 > > But with the same result. > > Thanks in advance, > > Regards, > > Soko Tica >
