Hello,
For what it's worth, I have the same issue on a bananapi M1 (tested on
6.1 release and current).
It remains possible to install openBSD on an USB stick and boot from it
by changing boot_targets order.
======
U-Boot SPL 2017.03 (Apr 01 2017 - 16:15:11)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2017.03 (Apr 01 2017 - 16:15:11 -0600) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: LeMaker Banana Pi
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Setting up a 720x576i composite-pal console (overscan 32x20)
In: serial
Out: vga
Err: vga
SCSI: SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: eth0: ethernet@01c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
USB device 0: unknown device
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /sun7i-a20-bananapi.dtb
35071 bytes read in 30 ms (1.1 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
64684 bytes read in 41 ms (1.5 MiB/s)
## Starting EFI application at 42000000 ...
Scanning disks on scsi...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 6 disks
>> OpenBSD/armv7 BOOTARM 0.5
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2174740+7984008+439148 [80+305280+145318]=0xa8e908
OpenBSD/armv7 booting ...
arg0 0xc0d8e908 arg1 0x0 arg2 0x48000000
Allocating page tables
freestart = 0x40d8f000, free_pages = 258267 (0x0003f0db)
IRQ stack: p0x40dbd000 v0xc0dbd000
ABT stack: p0x40dbe000 v0xc0dbe000
UND stack: p0x40dbf000 v0xc0dbf000
SVC stack: p0x40dc0000 v0xc0dc0000
Creating L1 page table at 0x40d90000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 0
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.1-current (RAMDISK) #131: Thu May 25 12:58:19 MDT 2017
dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1072078848 (1022MB)
avail mem = 1036992512 (988MB)
mainbus0 at root: LeMaker Banana Pi
cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
cortex0 at mainbus0
sxiccmu0 at mainbus0
psci0 at mainbus0
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
sxipio0 at simplebus0: 175 pins
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
sxiahci0 at simplebus0: AHCI 1.1
scsibus0 at sxiahci0: 32 targets
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
sxidog0 at simplebus0
sxirtc0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
com1 at simplebus0: ns16550, no working fifo
com2 at simplebus0: ns16550, no working fifo
dwge0 at simplebus0
dwge0: address: 02:0c:04:02:72:70
rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
ampintc0 at simplebus0 nirq 160, ncpu 2
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio0: 32 pins
sximmc0: timeout updating clock
sximmc0: timeout updating clock
sximmc0: timeout updating clock
sximmc0: timeout updating clock
sximmc0: timeout updating clock
sximmc0: timeout updating clock
sdmmc0: can't enable card
sximmc0: timeout updating clock
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 6.1 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') mybanana
Available network interfaces are: dwge0.
Which network interface do you wish to configure? (or 'done') [dwge0] done
DNS domain name? (e.g. 'bar.com') [my.domain]
DNS nameservers? (IP address list or 'none') [none]
Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Setup a user? (enter a lower-case loginname, or 'no') [no]
Since no user was setup, root logins via sshd(8) might be useful.
WARNING: root is targeted by password guessing attacks, pubkeys are safer.
Allow root ssh login? (yes, no, prohibit-password) [no]
Available disks are: none.
Which disk is the root disk? ('?' for details)
Le 04/09/17 à 13:13, soko.tica a écrit :
> Hello,
>
> As an update, ~current of April 8, 2017, still doesn't recognize sd card of
> the referred BananaPro. I should probably mention that sd card is 16GB
> size, unlike up to 4GB cards for the mother device (possibly both BananaPi
> and Cubieboard). Install script and dmesg follow.
>
> ======
> Script started on Sun Apr 9 12:50:19 2017
> $ cu -l cuaU0 -s 115200
> Connected to /dev/cuaU0 (speed 115200)
>
> U-Boot SPL 2016.07 (Jul 26 2016 - 02:49:44)
> DRAM: 1024 MiB
> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
> Trying to boot from MMC1
>
>
> U-Boot 2016.07 (Jul 26 2016 - 02:49:44 -0600) Allwinner Technology
>
> CPU: Allwinner A20 (SUN7I)
> Model: LeMaker Banana Pro
> I2C: ready
> DRAM: 1 GiB
> MMC: SUNXI SD/MMC: 0
> *** Warning - bad CRC, using default environment
>
> Setting up a 720x576i composite-pal console (overscan 32x20)
> In: serial
> Out: vga
> Err: vga
> SCSI: SATA link 0 timeout.
> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: ncq stag pm led clo only pmp pio slum part ccc apst
> Net: eth0: ethernet@01c50000
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB OHCI 1.0
> USB2: USB EHCI 1.00
> USB3: USB OHCI 1.0
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning bus 2 for devices... 1 USB Device(s) found
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc 0:1...
> Found EFI removable media binary efi/boot/bootarm.efi
> reading efi/boot/bootarm.efi
> 64684 bytes read in 44 ms (1.4 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> ## Starting EFI application at 0x42000000 ...
> Scanning disks on scsi...
> Scanning disks on usb...
> Scanning disks on mmc...
> MMC Device 1 not found
> MMC Device 2 not found
> MMC Device 3 not found
> Found 6 disks
>>> OpenBSD/armv7 BOOTARM 0.5
> boot>
> cannot open sd0a:/etc/random.seed: No such file or directory
> booting sd0a:/bsd: 2153176+7983908+438864 [80+301584+143437]=0xa851c0
>
> OpenBSD/armv7 booting ...
> arg0 0xc0d851c0 arg1 0x0 arg2 0x48000000
> Allocating page tables
> freestart = 0x40d86000, free_pages = 258276 (0x0003f0e4)
> IRQ stack: p0x40db4000 v0xc0db4000
> ABT stack: p0x40db5000 v0xc0db5000
> UND stack: p0x40db6000 v0xc0db6000
> SVC stack: p0x40db7000 v0xc0db7000
> Creating L1 page table at 0x40d88000
> Mapping kernel
> Constructing L2 page tables
> undefined page pmap board type: 0
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2017 OpenBSD. All rights reserved.
> https://www.OpenBSD.org
>
> OpenBSD 6.1-current (RAMDISK) #84: Sat Apr 8 17:04:11 MDT 2017
> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> real mem = 1072078848 (1022MB)
> avail mem = 1037033472 (988MB)
> mainbus0 at root: LeMaker Banana Pro
> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> cortex0 at mainbus0
> psci0 at mainbus0
> agtimer0 at mainbus0: tick rate 24000 KHz
> sxiccmu0 at mainbus0
> simplebus0 at mainbus0: "soc"
> sxipio0 at simplebus0: 175 pins
> sximmc0 at simplebus0
> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sximmc1 at simplebus0
> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> ehci0 at simplebus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> 2.00/1.00 addr 1
> sxiahci0 at simplebus0: AHCI 1.1
> scsibus0 at sxiahci0: 32 targets
> ehci1 at simplebus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> 2.00/1.00 addr 1
> sxidog0 at simplebus0
> sxirtc0 at simplebus0
> com0 at simplebus0: ns16550, no working fifo
> com0: console
> com1 at simplebus0: ns16550, no working fifo
> com2 at simplebus0: ns16550, no working fifo
> dwge0 at simplebus0
> dwge0: Ethernet address: 02:17:04:40:c0:cc
> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> ampintc0 at simplebus0 nirq 160, ncpu 2
> gpio0 at sxipio0: 32 pins
> gpio1 at sxipio0: 32 pins
> gpio2 at sxipio0: 32 pins
> gpio3 at sxipio0: 32 pins
> gpio4 at sxipio0: 32 pins
> gpio5 at sxipio0: 32 pins
> gpio6 at sxipio0: 32 pins
> gpio7 at sxipio0: 32 pins
> gpio8 at sxipio0: 32 pins
> sximmc0: timeout updating clock
> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sdmmc0: can't enable card
> sximmc0: timeout updating clock
> boot device: lookup 'sd0a:/bsd' failed.
> root on rd0a swap on rd0b dump on rd0b
> WARNING: preposterous clock chip time
> WARNING: CHECK AND RESET THE DATE!
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/armv7 6.1 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
> # date
> Sat Apr 8 22:51:29 GMT 2017
> # install
> At any prompt except password prompts you can escape to a shell by
> typing '!'. Default answers are shown in []'s and are selected by
> pressing RETURN. You can exit this program at any time by pressing
> Control-C, but this can leave your system in an inconsistent state.
>
> Terminal type? [vt220]
> System hostname? (short form, e.g. 'foo') bananapro
>
> Available network interfaces are: dwge0.
> Which network interface do you wish to configure? (or 'done') [dwge0]
> IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
> DHCPDISCOVER on dwge0 - interval 1
> DHCPOFFER from 192.168.4.1 (45:c9:e3:9b:a3:54)
> DHCPREQUEST on dwge0 to 255.255.255.255
> DHCPACK from 192.168.4.1 (45:c9:e3:9b:a3:54)
> bound to 192.168.4.10 -- renewal in 43199 seconds.
> IPv6 address for dwge0? (or 'rtsol' or 'none') [none]
> Available network interfaces are: dwge0.
> Which network interface do you wish to configure? (or 'done') [done]
> Using DNS domainname home.lan
> Using DNS nameservers at 192.168.4.1 192.168.5.1
>
> Password for root account? (will not echo)
> Password for root account? (again)
> Start sshd(8) by default? [yes]
> Setup a user? (enter a lower-case loginname, or 'no') [no]
> Since no user was setup, root logins via sshd(8) might be useful.
> WARNING: root is targeted by password guessing attacks, pubkeys are safer.
> Allow root ssh login? (yes, no, prohibit-password) [no]
> What timezone are you in? ('?' for list) [Europe/Belgrade]
>
> Available disks are: none.
> Which disk is the root disk? ('?' for details) ?
> Available disks are: none.
> Which disk is the root disk? ('?' for details) Available disks are: none.
> Which disk is the root disk? ('?' for details) ^C
>
> # dmesg
> OpenBSD 6.1-current (RAMDISK) #84: Sat Apr 8 17:04:11 MDT 2017
> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
> real mem = 1072078848 (1022MB)
> avail mem = 1037033472 (988MB)
> mainbus0 at root: LeMaker Banana Pro
> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
> cortex0 at mainbus0
> psci0 at mainbus0
> agtimer0 at mainbus0: tick rate 24000 KHz
> sxiccmu0 at mainbus0
> simplebus0 at mainbus0: "soc"
> sxipio0 at simplebus0: 175 pins
> sximmc0 at simplebus0
> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sximmc1 at simplebus0
> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
> ehci0 at simplebus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> 2.00/1.00 addr 1
> sxiahci0 at simplebus0: AHCI 1.1
> scsibus0 at sxiahci0: 32 targets
> ehci1 at simplebus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
> 2.00/1.00 addr 1
> sxidog0 at simplebus0
> sxirtc0 at simplebus0
> com0 at simplebus0: ns16550, no working fifo
> com0: console
> com1 at simplebus0: ns16550, no working fifo
> com2 at simplebus0: ns16550, no working fifo
> dwge0 at simplebus0
> dwge0: Ethernet address: 02:17:04:40:c0:cc
> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
> ampintc0 at simplebus0 nirq 160, ncpu 2
> gpio0 at sxipio0: 32 pins
> gpio1 at sxipio0: 32 pins
> gpio2 at sxipio0: 32 pins
> gpio3 at sxipio0: 32 pins
> gpio4 at sxipio0: 32 pins
> gpio5 at sxipio0: 32 pins
> gpio6 at sxipio0: 32 pins
> gpio7 at sxipio0: 32 pins
> gpio8 at sxipio0: 32 pins
> sximmc0: timeout updating clock
> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sximmc0: timeout updating clock
> sdmmc0: can't enable card
> sximmc0: timeout updating clock
> boot device: lookup 'sd0a:/bsd' failed.
> root on rd0a swap on rd0b dump on rd0b
> WARNING: preposterous clock chip time
> WARNING: CHECK AND RESET THE DATE!
> # halt -p
> syncing disks... done
>
> Attempting to power down...
> The operating system has halted.
> Please press any key to reboot.
>
>
> [EOT]
> $ ^D
>
> Script done on Sun Apr 9 12:54:36 2017
>
>
> On Sun, Oct 30, 2016 at 10:00 AM, soko.tica <soko.t...@gmail.com> wrote:
>
>> Thank you for your input.
>>
>> For the record, FreeBSD 11.0-RC3 worked on each of these SD cards.
>>
>> In the case that it might obe of interest for anyone, i paste here a new
>> typescript, starting from downloading and veryfing the images, preparing
>> miniroot and starting the installation, which cannot recognize the sd card
>> on which it is running, showing no available disks. That is why I tried to
>> install from one SD card to another, thinking it is supposed to be so until
>> I saw that usb stick recognizes itself as the target disk.
>>
>>
>> =====
>> Script started on Sun Oct 30 10:31:43 2016
>> $ fdisk sd1
>> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
>> Offset: 0 Signature: 0xAA55
>> Starting Ending LBA Info:
>> #: id C H S - C H S [ start: size
>> ]
>> ------------------------------------------------------------
>> -------------------
>> *0: 0C 0 32 33 - 0 97 33 [ 2048: 4096 ]
>> Win95 FAT32L
>> 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
>> 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused
>> 3: A6 0 97 34 - 2 75 9 [ 6144: 30720 ]
>> OpenBSD
>> $ doas fdisk -e sd1
>> Enter 'help' for information
>> fdisk: 1> p m
>> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
>> Offset: 0 Signature: 0xAA55
>> Starting Ending LBA Info:
>> #: id C H S - C H S [ start: size
>> ]
>> ------------------------------------------------------------
>> -------------------
>> *0: 0C 0 32 33 - 0 97 33 [ 2048: 2M] Win95
>> FAT32L
>> 1: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> 2: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> 3: A6 0 97 34 - 2 75 9 [ 6144: 15M]
>> OpenBSD
>> fdisk: 1> e 0
>> Starting Ending LBA Info:
>> #: id C H S - C H S [ start: size
>> ]
>> ------------------------------------------------------------
>> -------------------
>> *0: 0C 0 32 33 - 0 97 33 [ 2048: 4096 ]
>> Win95 FAT32L
>> Partition id ('0' to disable) [01 - FF]: [C] (? for help) 0
>> Partition 0 is disabled.
>> fdisk:*1> e 3
>> Starting Ending LBA Info:
>> #: id C H S - C H S [ start: size
>> ]
>> ------------------------------------------------------------
>> -------------------
>> 3: A6 0 97 34 - 2 75 9 [ 6144: 30720 ]
>> OpenBSD
>> Partition id ('0' to disable) [01 - FF]: [A6] (? for help) 0
>> Partition 3 is disabled.
>> fdisk:*1> p m
>> Disk: sd1 geometry: 1887/255/63 [30318592 Sectors]
>> Offset: 0 Signature: 0xAA55
>> Starting Ending LBA Info:
>> #: id C H S - C H S [ start: size
>> ]
>> ------------------------------------------------------------
>> -------------------
>> 0: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> 1: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> 2: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> 3: 00 0 0 0 - 0 0 0 [ 0: 0M] unused
>> fdisk:*1> w
>> Writing MBR at offset 0.
>> fdisk: 1> q
>> $ disklabel sd1
>> # /dev/rsd1c:
>> type: SCSI
>> disk: SCSI disk
>> label: Storage Device
>> duid: 0000000000000000
>> flags:
>> bytes/sector: 512
>> sectors/track: 63
>> tracks/cylinder: 255
>> sectors/cylinder: 16065
>> cylinders: 1887
>> total sectors: 30318592
>> boundstart: 0
>> boundend: 30318592
>> drivedata: 0
>>
>> 16 partitions:
>> # size offset fstype [fsize bsize cpg]
>> c: 30318592 0 unused
>> $ pwd
>> /home/doasuser
>> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/SHA256.sig
>> Trying 91.185.196.203...
>> Connected to ftp.obsd.si.
>> 220 nina.kerberos.si FTP server ready.
>> 331 Guest login ok, send your email address as password.
>> 230 Guest login ok, access restrictions apply.
>> Remote system type is UNIX.
>> Using binary mode to transfer files.
>> 200 Type set to I.
>> 250 CWD command successful.
>> Retrieving pub/OpenBSD/snapshots/armv7/SHA256.sig
>> local: SHA256.sig remote: SHA256.sig
>> 150 Opening BINARY mode data connection for 'SHA256.sig' (1978 bytes).
>> 100% |**************************************************| 1978
>> 00:00 ETA
>> 226 Transfer complete.
>> 1978 bytes received in 0.20 seconds (9.45 KB/s)
>> 221 Goodbye.
>> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/SHA256.sig
>> Trying 91.185.196.203...
>> Connected to ftp.obsd.si.
>> 220 nina.kerberos.si FTP server ready.
>> 331 Guest login ok, send your email address as password.
>> 230 Guest login ok, access restrictions apply.
>> Remote system type is UNIX.
>> Using binary mode to transfer files.
>> 200 Type set to I.
>> 250 CWD command successful.
>> Retrieving pub/OpenBSD/snapshots/armv7/SHA256
>> local: SHA256 remote: SHA256
>> 150 Opening BINARY mode data connection for 'SHA256' (1815 bytes).
>> 100% |**************************************************| 1815
>> 00:00 ETA
>> 226 Transfer complete.
>> 1815 bytes received in 0.21 seconds (8.32 KB/s)
>> 221 Goodbye.
>> $ ftp ftp://ftp.obsd.si/pub/OpenBSD/snapshots/armv7/miniroot-cubie-60.fs
>> Trying 91.185.196.203...
>> Connected to ftp.obsd.si.
>> 220 nina.kerberos.si FTP server ready.
>> 331 Guest login ok, send your email address as password.
>> 230 Guest login ok, access restrictions apply.
>> Remote system type is UNIX.
>> Using binary mode to transfer files.
>> 200 Type set to I.
>> 250 CWD command successful.
>> Retrieving pub/OpenBSD/snapshots/armv7/miniroot-cubie-60.fs
>> local: miniroot-cubie-60.fs remote: miniroot-cubie-60.fs
>> 150 Opening BINARY mode data connection for 'miniroot-cubie-60.fs'
>> (18874368 bytes).
>> 100% |**************************************************| 18432 KB
>> 00:18 ETA
>> 226 Transfer complete.
>> 18874368 bytes received in 18.17 seconds (1014.66 KB/s)
>> 221 Goodbye.
>> $ sha256 -c SHA256
>> sha256: cannot open BOOTARM.EFI: No such file or directory
>> (SHA256) BOOTARM.EFI: MISSING
>> sha256: cannot open BUILDINFO: No such file or directory
>> (SHA256) BUILDINFO: MISSING
>> sha256: cannot open INSTALL.armv7: No such file or directory
>> (SHA256) INSTALL.armv7: MISSING
>> sha256: cannot open base60.tgz: No such file or directory
>> (SHA256) base60.tgz: MISSING
>> sha256: cannot open bsd: No such file or directory
>> (SHA256) bsd: MISSING
>> sha256: cannot open bsd.rd: No such file or directory
>> (SHA256) bsd.rd: MISSING
>> sha256: cannot open comp60.tgz: No such file or directory
>> (SHA256) comp60.tgz: MISSING
>> sha256: cannot open game60.tgz: No such file or directory
>> (SHA256) game60.tgz: MISSING
>> sha256: cannot open man60.tgz: No such file or directory
>> (SHA256) man60.tgz: MISSING
>> sha256: cannot open miniroot-am335x-60.fs: No such file or directory
>> (SHA256) miniroot-am335x-60.fs: MISSING
>> sha256: cannot open miniroot-beagle-60.fs: No such file or directory
>> (SHA256) miniroot-beagle-60.fs: MISSING
>> (SHA256) miniroot-cubie-60.fs: OK
>> sha256: cannot open miniroot-cubox-60.fs: No such file or directory
>> (SHA256) miniroot-cubox-60.fs: MISSING
>> sha256: cannot open miniroot-nitrogen-60.fs: No such file or directory
>> (SHA256) miniroot-nitrogen-60.fs: MISSING
>> sha256: cannot open miniroot-panda-60.fs: No such file or directory
>> (SHA256) miniroot-panda-60.fs: MISSING
>> sha256: cannot open miniroot-wandboard-60.fs: No such file or directory
>> (SHA256) miniroot-wandboard-60.fs: MISSING
>> sha256: cannot open xbase60.tgz: No such file or directory
>> (SHA256) xbase60.tgz: MISSING
>> sha256: cannot open xfont60.tgz: No such file or directory
>> (SHA256) xfont60.tgz: MISSING
>> sha256: cannot open xserv60.tgz: No such file or directory
>> (SHA256) xserv60.tgz: MISSING
>> sha256: cannot open xshare60.tgz: No such file or directory
>> (SHA256) xshare60.tgz: MISSING
>> $ sha256 -c SHA256 | grep 'OK'
>> sha256: cannot open BOOTARM.EFI: No such file or directory
>> sha256: cannot open BUILDINFO: No such file or directory
>> sha256: cannot open INSTALL.armv7: No such file or directory
>> sha256: cannot open base60.tgz: No such file or directory
>> sha256: cannot open bsd: No such file or directory
>> sha256: cannot open bsd.rd: No such file or directory
>> sha256: cannot open comp60.tgz: No such file or directory
>> sha256: cannot open game60.tgz: No such file or directory
>> sha256: cannot open man60.tgz: No such file or directory
>> sha256: cannot open miniroot-am335x-60.fs: No such file or directory
>> sha256: cannot open miniroot-beagle-60.fs: No such file or directory
>> sha256: cannot open miniroot-cubox-60.fs: No such file or directory
>> sha256: cannot open miniroot-nitrogen-60.fs: No such file or directory
>> sha256: cannot open miniroot-panda-60.fs: No such file or directory
>> sha256: cannot open miniroot-wandboard-60.fs: No such file or directory
>> sha256: cannot open xbase60.tgz: No such file or directory
>> sha256: cannot open xfont60.tgz: No such file or directory
>> sha256: cannot open xserv60.tgz: No such file or directory
>> sha256: cannot open xshare60.tgz: No such file or directory
>> (SHA256) miniroot-cubie-60.fs: OK
>> gnify/openbsd-60-base.pub.-xbSHA256.sig.siSH <
>> Signature Verified
>> miniroot-cubie-60.fs: OK
>> BOOTARM.EFI: FAIL
>> miniroot-beagle-60.fs: FAIL
>> bsd: FAIL
>> bsd.rd: FAIL
>> miniroot-cubox-60.fs: FAIL
>> game60.tgz: FAIL
>> comp60.tgz: FAIL
>> miniroot-nitrogen-60.fs: FAIL
>> xserv60.tgz: FAIL
>> miniroot-am335x-60.fs: FAIL
>> xshare60.tgz: FAIL
>> xbase60.tgz: FAIL
>> base60.tgz: FAIL
>> miniroot-panda-60.fs: FAIL
>> xfont60.tgz: FAIL
>> man60.tgz: FAIL
>> BUILDINFO: FAIL
>> miniroot-wandboard-60.fs: FAIL
>> INSTALL.armv7: FAIL
>> $ signify -C -p /etc/signify/openbsd-60-base.pub -x SHA256.sig | grep 'OK'
>> miniroot-cubie-60.fs: OK
>> BOOTARM.EFI: FAIL
>> miniroot-beagle-60.fs: FAIL
>> bsd: FAIL
>> bsd.rd: FAIL
>> miniroot-cubox-60.fs: FAIL
>> game60.tgz: FAIL
>> comp60.tgz: FAIL
>> miniroot-nitrogen-60.fs: FAIL
>> xserv60.tgz: FAIL
>> miniroot-am335x-60.fs: FAIL
>> xshare60.tgz: FAIL
>> xbase60.tgz: FAIL
>> base60.tgz: FAIL
>> miniroot-panda-60.fs: FAIL
>> xfont60.tgz: FAIL
>> man60.tgz: FAIL
>> BUILDINFO: FAIL
>> miniroot-wandboard-60.fs: FAIL
>> INSTALL.armv7: FAIL
>> oasovnconfigfvnd0nminiroot-cubie-60.fs <
>> $ doas dd if=/usr/local/share/u-boot/AananaPr
>> A10-OLinuXino-Lime/ A20-OLinuXino-Lime/ A20-OLinuXino_MICRO/
>> A10s-OLinuXino-M/ A20-OLinuXino-Lime2/
>> ot/Bananapro/u-boot-sunxi-with-spl.binaof=/dev/rvnd0c-bs=1024 seek=8
>> <
>> 476+1 records in
>> 476+1 records out
>> 488235 bytes transferred in 0.034 secs (14271287 bytes/sec)
>> $ disklabel vnd0
>> disklabel: ioctl DIOCGDINFO: Operation not permitted
>> $ doas disklabel vnd0
>> # /dev/rvnd0c:
>> type: vnd
>> disk: vnd device
>> label: fictitious
>> duid: b7b29d6a08b186c2
>> flags:
>> bytes/sector: 512
>> sectors/track: 256
>> tracks/cylinder: 16
>> sectors/cylinder: 4096
>> cylinders: 9
>> total sectors: 36864
>> boundstart: 6144
>> boundend: 36864
>> drivedata: 0
>>
>> 16 partitions:
>> # size offset fstype [fsize bsize cpg]
>> a: 30720 6144 4.2BSD 2048 16384 240
>> c: 36864 0 unused
>> i: 4096 2048 MSDOS
>> $ doas mount /dev/vnd0i /mnt/usb
>> $ ls -lh /mnt/usb
>> total 80
>> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
>> -rw-r--r-- 1 root wheel 33.4K Oct 30 01:32 sun7i-a20-cubieboard2.dtb
>> $rmo/mnt/usb/sun7i-a20-cubieboard2.dtb <
>> $ lsa-lhm/mnt/usbb/sun7i-a20-cubieboard2.dtb
>> total 8
>> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
>> $ doas cp /usr/local/share/dtb/arm
>> arm/ arm64/
>> tb/arm/sun7i-a20-bananapro.dtbd/mnt/usbusn20-bananapr <
>> $ lsa-lhp/mnt/usbcal/share/dtb/arm/sun7i-a20-bananapro.dtb /mnt/usb
>> total 80
>> drwxr-xr-x 1 root wheel 4.0K Oct 30 01:32 efi
>> -rw-r--r-- 1 root wheel 33.6K Oct 30 10:37 sun7i-a20-bananapro.dtb
>> $ doas umount /mnt/usb
>> $ doas vnconfig -u vnd0
>> $ ls -lh
>> total 36948
>> -rw-r--r-- 1 doasuser doasuser 1.8K Oct 30 05:21 SHA256
>> -rw-r--r-- 1 doasuser doasuser 1.9K Oct 30 05:21 SHA256.sig
>> -rw-r--r-- 1 doasuser doasuser 18.0M Oct 30 10:37 miniroot-cubie-60.fs
>> -rw-r--r-- 1 doasuser doasuser 20.8K Oct 30 10:39 typescript
>> $ doas if=miniroot-cubie-60.fs of=/dev/rsd1c bs=1024
>> doas: if=miniroot-cubie-60.fs: command not found
>> $ doas ddiif=miniroot-cubie-60.fsoof=/dev/rsd1cbbs=1024
>> 18432+0 records in
>> 18432+0 records out
>> 18874368 bytes transferred in 15.508 secs (1217046 bytes/sec)
>> $ cu -l cuaU0 -s 115200
>> cu: open("/dev/cuaU0"): Permission denied
>> $ whoami
>> doasuser
>> $ doas cu -l cuaU0 -s 115200
>> Connected to /dev/cuaU0 (speed 115200)
>>
>> U-Boot SPL 2016.09 (Sep 20 2016 - 02:39:19)
>> DRAM: 1024 MiB
>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
>> Trying to boot from MMC1
>>
>>
>>
>> U-Boot 2016.09 (Sep 20 2016 - 02:39:19 -0600) Allwinner Technology
>>
>> CPU: Allwinner A20 (SUN7I)
>> Model: LeMaker Banana Pro
>> I2C: ready
>> DRAM: 1 GiB
>> MMC: SUNXI SD/MMC: 0
>> *** Warning - bad CRC, using default environment
>>
>> Setting up a 720x576i composite-pal console (overscan 32x20)
>> In: serial
>> Out: vga
>> Err: vga
>> SCSI: SATA link 0 timeout.
>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>> Net: eth0: ethernet@01c50000
>> starting USB...
>> USB0: USB EHCI 1.00
>> USB1: USB OHCI 1.0
>> USB2: USB EHCI 1.00
>> USB3: USB OHCI 1.0
>> scanning bus 0 for devices... 1 USB Device(s) found
>> scanning bus 2 for devices... 1 USB Device(s) found
>> Hit any key to stop autoboot: 0
>> switch to partitions #0, OK
>> mmc0 is current device
>> Scanning mmc 0:1...
>> reading /sun7i-a20-bananapro.dtb
>> 34451 bytes read in 29 ms (1.1 MiB/s)
>> Found EFI removable media binary efi/boot/bootarm.efi
>> reading efi/boot/bootarm.efi
>> 64684 bytes read in 40 ms (1.5 MiB/s)
>> ## Starting EFI application at 0x42000000 ...
>> CACHE: Misaligned operation at range [79f1d000, 79f2ccac]
>> Scanning disks on scsi...
>> Scanning disks on usb...
>> Scanning disks on mmc...
>> MMC Device 1 not found
>> MMC Device 2 not found
>> MMC Device 3 not found
>> Found 6 disks
>>>> OpenBSD/armv7 BOOTARM 0.5
>> boot>
>> cannot open sd0a:/etc/random.seed: No such file or directory
>> booting sd0a:/bsd: 2138360+7972148+442776 [80+310912+150523]=0xa87334
>>
>> OpenBSD/armv7 booting ...
>> arg0 0xc0d87334 arg1 0x0 arg2 0x48000000
>> Allocating page tables
>> freestart = 0x40d88000, free_pages = 258274 (0x0003f0e2)
>> IRQ stack: p0x40db6000 v0xc0db6000
>> ABT stack: p0x40db7000 v0xc0db7000
>> UND stack: p0x40db8000 v0xc0db8000
>> SVC stack: p0x40db9000 v0xc0db9000
>> Creating L1 page table at 0x40d88000
>> Mapping kernel
>> Constructing L2 page tables
>> undefined page pmap board type: 0
>> Copyright (c) 1982, 1986, 1989, 1991, 1993
>> The Regents of the University of California. All rights reserved.
>> Copyright (c) 1995-2016 OpenBSD. All rights reserved.
>> https://www.OpenBSD.org
>>
>> OpenBSD 6.0-current (RAMDISK) #0: Sat Oct 29 17:32:38 MDT 2016
>> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
>> real mem = 1072078848 (1022MB)
>> avail mem = 1037021184 (988MB)
>>
>> mainbus0 at root: LeMaker Banana Pro
>> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
>> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
>> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
>> cortex0 at mainbus0
>> agtimer0 at mainbus0: tick rate 24000 KHz
>> sxiccmu0 at mainbus0
>> simplebus0 at mainbus0: "soc"
>> sxipio0 at simplebus0: 175 pins
>> sximmc0 at simplebus0
>> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
>> sximmc1 at simplebus0
>> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
>> ehci0 at simplebus0
>> usb0 at ehci0: USB revision 2.0
>> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub" rev
>> 2.00/1.00 addr 1
>> sxiahci0 at simplebus0: AHCI 1.1
>> scsibus0 at sxiahci0: 32 targets
>> ehci1 at simplebus0
>> usb1 at ehci1: USB revision 2.0
>> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub" rev
>> 2.00/1.00 addr 1
>> sxidog0 at simplebus0
>> sxirtc0 at simplebus0
>> com0 at simplebus0: ns16550, no working fifo
>> com0: console
>> com1 at simplebus0: ns16550, no working fifo
>> com2 at simplebus0: ns16550, no working fifo
>> dwge0 at simplebus0
>> dwge0: Ethernet address: 02:17:04:40:c0:cc
>> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
>> ampintc0 at simplebus0 nirq 160
>> gpio0 at sxipio0: 18 pins
>> gpio1 at sxipio0: 24 pins
>> gpio2 at sxipio0: 25 pins
>> gpio3 at sxipio0: 28 pins
>> gpio4 at sxipio0: 12 pins
>> gpio5 at sxipio0: 6 pins
>> gpio6 at sxipio0: 12 pins
>> gpio7 at sxipio0: 28 pins
>> gpio8 at sxipio0: 22 pins
>> sximmc0: timeout updating clock
>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not configured
>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not configured
>> sximmc0: timeout updating clock
>> sximmc0: timeout updating clock
>> sximmc0: timeout updating clock
>> sximmc0: timeout updating clock
>> sximmc0: timeout updating clock
>> sdmmc0: can't enable card
>> sximmc0: timeout updating clock
>> boot device: lookup 'sd0a:/bsd' failed.
>> root on rd0a swap on rd0b dump on rd0b
>> WARNING: clock lost 17103 days
>> WARNING: CHECK AND RESET THE DATE!
>> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>>
>> Welcome to the OpenBSD/armv7 6.0 installation program.
>> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
>> At any prompt except password prompts you can escape to a shell by
>> typing '!'. Default answers are shown in []'s and are selected by
>> pressing RETURN. You can exit this program at any time by pressing
>> Control-C, but this can leave your system in an inconsistent state.
>>
>> Terminal type? [vt220]
>> System hostname? (short form, e.g. 'foo') banana
>>
>> Available network interfaces are: dwge0.
>> Which network interface do you wish to configure? (or 'done') [dwge0]
>> IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp]
>> DHCPDISCOVER on dwge0 - interval 1
>> DHCPOFFER from 192.168.1.1 (a4:79:47:e5:05:32)
>> DHCPREQUEST on dwge0 to 255.255.255.255
>> DHCPACK from 192.168.1.1 (a4:79:47:e5:05:32)
>> bound to 192.168.1.2 -- renewal in 43200 seconds.
>> IPv6 address for dwge0? (or 'rtsol' or 'none') [none]
>> Available network interfaces are: dwge0.
>> Which network interface do you wish to configure? (or 'done') [done]
>> Using DNS domainname my.domain
>> Using DNS nameservers at 192.168.1.1 192.168.1.1
>>
>> Password for root account? (will not echo)
>> Password for root account? (again)
>> Start sshd(8) by default? [yes]
>> Setup a user? (enter a lower-case loginname, or 'no') [no]
>> Since no user was setup, root logins via sshd(8) might be useful.
>> WARNING: root is targeted by password guessing attacks, pubkeys are safer.
>> Allow root ssh login? (yes, no, prohibit-password) [no]
>> What timezone are you in? ('?' for list) [Europe/Belgrade]
>>
>> Available disks are: none.
>> Which disk is the root disk? ('?' for details) ?
>> Available disks are: none.
>> Which disk is the root disk? ('?' for details) ^C
>>
>> # halt
>> syncing disks... done
>> The operating system has halted.
>> Please press any key to reboot.
>>
>> Killed
>> $ exit
>>
>> Script done on Sun Oct 30 10:46:35 2016
>>
>> ===
>>
>> On Sun, Oct 30, 2016 at 8:21 AM, Jonathan Gray <j...@jsg.id.au> wrote:
>>
>>> ommmc is for omap not sunxi. sximmc is the sunxi equivalent.
>>>
>>> sximmc0: timeout updating clock
>>> sximmc0: timeout updating clock
>>> sximmc0: timeout updating clock
>>> sximmc0: timeout updating clock
>>> sximmc0: timeout updating clock
>>> sximmc0: timeout updating clock
>>> sdmmc0: can't enable card
>>> sximmc0: timeout updating clock
>>>
>>> If the cause of that were found and fixed, sd0 would attach.
>>> sximmc works on other a20 based systems, it isn't clear what
>>> makes this one different besides having multiple sximmc devices.
>>>
>>> On Sun, Oct 30, 2016 at 08:09:24AM +0100, soko.tica wrote:
>>>> It seems that "the mistery" is solved - OpenBSD doesn't have support for
>>>> ommc http://man.openbsd.org/OpenBSD-current/man4/armv7/ommmc.4 on sunxi
>>>> https://www.openbsd.org/armv7.html
>>>>
>>>> Once the miniroot is written to usb stick it is able to install on the
>>> same
>>>> usb stick.
>>>>
>>>> In the case I am still wrong about this, don't be shy to write it here,
>>>> someone might read it in future.
>>>>
>>>> Regards,
>>>>
>>>> Soko Tica
>>>>
>>>> On Sat, Oct 29, 2016 at 10:19 PM, soko.tica <soko.t...@gmail.com>
>>> wrote:
>>>>> Hello,
>>>>>
>>>>> I have managed to successfully install -current on BananaPro
>>> (allegedly
>>>>> the same board as BananaPi plus wi-fi), but the boot can't be
>>> completed
>>>>> because
>>>>> "boot device: lookup 'sd0a:/bsd' failed"
>>>>> although it was initially found (as shown in the typescript bellow).
>>>>>
>>>>> I performed the install(s) from a SD card plugged into micro card
>>> slot to
>>>>> another SD card plugged into usb card reader. I did edit partition
>>> sizes
>>>>> suggested by autopartition. Upon completing the install I place the
>>> target
>>>>> SD card into the micro card slot and try to boot.
>>>>>
>>>>> Please advise if I am missing something obvious.
>>>>>
>>>>> Output of the typescript
>>>>> ========================
>>>>> U-Boot 2016.09 (Sep 20 2016 - 02:39:19 -0600) Allwinner Technology
>>>>>
>>>>> CPU: Allwinner A20 (SUN7I)
>>>>> Model: LeMaker Banana Pro
>>>>> I2C: ready
>>>>> DRAM: 1 GiB
>>>>> MMC: SUNXI SD/MMC: 0
>>>>> *** Warning - bad CRC, using default environment
>>>>>
>>>>> Setting up a 720x576i composite-pal console (overscan 32x20)
>>>>> In: serial
>>>>> Out: vga
>>>>> Err: vga
>>>>> SCSI: SATA link 0 timeout.
>>>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
>>>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>>>>> Net: eth0: ethernet@01c50000
>>>>> starting USB...
>>>>> USB0: USB EHCI 1.00
>>>>> USB1: USB OHCI 1.0
>>>>> USB2: USB EHCI 1.00
>>>>> USB3: USB OHCI 1.0
>>>>> scanning bus 0 for devices... 1 USB Device(s) found
>>>>> scanning bus 2 for devices... 1 USB Device(s) found
>>>>> Hit any key to stop autoboot: 0
>>>>> switch to partitions #0, OK
>>>>> mmc0 is current device
>>>>> Scanning mmc 0:1...
>>>>> reading /sun7i-a20-bananapro.dtb
>>>>> 31159 bytes read in 30 ms (1013.7 KiB/s)
>>>>> Found EFI removable media binary efi/boot/bootarm.efi
>>>>> reading efi/boot/bootarm.efi
>>>>> 64684 bytes read in 41 ms (1.5 MiB/s)
>>>>> ## Starting EFI application at 0x42000000 ...
>>>>> CACHE: Misaligned operation at range [79f1d000, 79f2ccac]
>>>>> Scanning disks on scsi...
>>>>> Scanning disks on usb...
>>>>> Scanning disks on mmc...
>>>>> MMC Device 1 not found
>>>>> MMC Device 2 not found
>>>>> MMC Device 3 not found
>>>>> Found 6 disks
>>>>>>> OpenBSD/armv7 BOOTARM 0.5
>>>>> boot>
>>>>> cannot open sd0a:/etc/random.seed: No such file or directory
>>>>> booting sd0a:/bsd: 2138412+7972140+442552 [80+310912+150523]=0xa8724c
>>>>>
>>>>> OpenBSD/armv7 booting ...
>>>>> arg0 0xc0d8724c arg1 0x0 arg2 0x48000000
>>>>> Allocating page tables
>>>>> freestart = 0x40d88000, free_pages = 258274 (0x0003f0e2)
>>>>> IRQ stack: p0x40db6000 v0xc0db6000
>>>>> ABT stack: p0x40db7000 v0xc0db7000
>>>>> UND stack: p0x40db8000 v0xc0db8000
>>>>> SVC stack: p0x40db9000 v0xc0db9000
>>>>> Creating L1 page table at 0x40d88000
>>>>> Mapping kernel
>>>>> Constructing L2 page tables
>>>>> undefined page pmap board type: 0
>>>>> Copyright (c) 1982, 1986, 1989, 1991, 1993
>>>>> The Regents of the University of California. All rights reserved.
>>>>> Copyright (c) 1995-2016 OpenBSD. All rights reserved.
>>>>> https://www.OpenBSD.org
>>>>>
>>>>> OpenBSD 6.0-current (RAMDISK) #0: Tue Oct 25 02:52:36 MDT 2016
>>>>> dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
>>>>> real mem = 1072078848 (1022MB)
>>>>> avail mem = 1037025280 (988MB)
>>>>> mainbus0 at root: LeMaker Banana Pro
>>>>> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core)
>>>>> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
>>>>> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache
>>>>> cortex0 at mainbus0
>>>>> agtimer0 at mainbus0: tick rate 24000 KHz
>>>>> sxiccmu0 at mainbus0
>>>>> simplebus0 at mainbus0: "soc"
>>>>> sxipio0 at simplebus0: 175 pins
>>>>> sximmc0 at simplebus0
>>>>> sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
>>>>> sximmc1 at simplebus0
>>>>> sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
>>>>> ehci0 at simplebus0
>>>>> usb0 at ehci0: USB revision 2.0
>>>>> uhub0 at usb0 configuration 1 interface 0 "Allwinner EHCI root hub"
>>> rev
>>>>> 2.00/1.00 addr 1
>>>>> sxiahci0 at simplebus0: AHCI 1.1
>>>>> scsibus0 at sxiahci0: 32 targets
>>>>> ehci1 at simplebus0
>>>>> usb1 at ehci1: USB revision 2.0
>>>>> uhub1 at usb1 configuration 1 interface 0 "Allwinner EHCI root hub"
>>> rev
>>>>> 2.00/1.00 addr 1
>>>>> sxidog0 at simplebus0
>>>>> sxirtc0 at simplebus0
>>>>> com0 at simplebus0: ns16550, no working fifo
>>>>> com0: console
>>>>> com1 at simplebus0: ns16550, no working fifo
>>>>> com2 at simplebus0: ns16550, no working fifo
>>>>> dwge0 at simplebus0
>>>>> dwge0: Ethernet address: 02:17:04:40:c0:cc
>>>>> rgephy0 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
>>>>> ampintc0 at simplebus0 nirq 160
>>>>> gpio0 at sxipio0: 18 pins
>>>>> gpio1 at sxipio0: 24 pins
>>>>> gpio2 at sxipio0: 25 pins
>>>>> gpio3 at sxipio0: 28 pins
>>>>> gpio4 at sxipio0: 12 pins
>>>>> gpio5 at sxipio0: 6 pins
>>>>> gpio6 at sxipio0: 12 pins
>>>>> gpio7 at sxipio0: 28 pins
>>>>> gpio8 at sxipio0: 22 pins
>>>>> sximmc0: timeout updating clock
>>>>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 1 not
>>> configured
>>>>> (manufacturer 0x2d0, product 0xa962)at sdmmc1 function 2 not
>>> configured
>>>>> sximmc0: timeout updating clock
>>>>> sximmc0: timeout updating clock
>>>>> sximmc0: timeout updating clock
>>>>> sximmc0: timeout updating clock
>>>>> sximmc0: timeout updating clock
>>>>> sdmmc0: can't enable card
>>>>> sximmc0: timeout updating clock
>>>>> boot device: lookup 'sd0a:/bsd' failed.
>>>>> root on rd0a swap on rd0b dump on rd0b
>>>>> WARNING: clock lost 17099 days
>>>>> WARNING: CHECK AND RESET THE DATE!
>>>>> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>>>>>
>>>>> ===========================
>>>>>
>>>>> Several times I also tried with interrupting the boot and
>>>>>
>>>>> => run findfdt
>>>>> => load mmc 0:1 ${fdt_addr_r} ${fdtfile}
>>>>> => load mmc 0:1 ${kernel_addr_r} efi/boot/bootarm.efi
>>>>> => bootefi ${kernel_addr_r} ${fdt_addr_r}
>>>>>
>>>>> as per the instructions ftp://ftp.obsd.si/pub/OpenBSD/
>>>>> snapshots/armv7/INSTALL.armv7
>>>>>
>>>>> But with the same result.
>>>>>
>>>>> Thanks in advance,
>>>>>
>>>>> Regards,
>>>>>
>>>>> Soko Tica
>>>>>
>>
>
