On 10/12/2014 07:34 AM, Raphael Graf wrote:
> [..]
> This snapshot works fine on my BeagleBone (rev. A5C, 2GB eMMC), dmesg below.
> No idea what you're missing. Can you send a dmesg?
>
> [..]
Please find below the console outputs of my
1.) rev. B, 2GB eMMC
2.) rev. C, 4GB eMMC
Note that rev. C is the current production model, and rev. B was the
previous production model from a few months ago. The rev. A5C is
considerably older. Again, the rev. B is able to detect sd1 under
OpenBSD 5.5. Hope this helps!
Thanks,
~Max
### rev. B #############################################
U-Boot SPL 2013.04.-00014-g47880f5 (Apr 22 2014 - 13:23:54)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
Net: <ethaddr> not set, Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
159 bytes read in 4 ms (38.1 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
reading bsd.umg
7423360 bytes read in 437 ms (16.2 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7423296 Bytes = 7.1 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting Kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x80a15000, free_pages = 128491 (0x0001f5eb)
IRQ stack: p0x80a43000 v0xc0a43000
ABT stack: p0x80a44000 v0xc0a44000
UND stack: p0x80a45000 v0xc0a45000
SVC stack: p0x80a46000 v0xc0a46000
Creating L1 page table at 0x80a18000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 173468 bytes of bsd ELF symbol table ]
board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6-current (RAMDISK-OMAP) #1: Thu Oct 9 20:24:32 AEDT 2014
r...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK-OMAP
real mem = 536870912 (512MB)
avail mem = 515182592 (491MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/1,4way) I-cache, 32KB(64b/1,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
omgpio0 at omap0: rev 0.1
omgpio1 at omap0: rev 0.1
omgpio2 at omap0: rev 0.1
omgpio3 at omap0: rev 0.1
omap0: device tiiic unit 0 not configured
omap0: device tiiic unit 1 not configured
omap0: device tiiic unit 2 not configured
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at ompa0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address 90:59:af:95:f8:c2
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1:OUI
0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15193MB, 512 bytes/sector, 31116288 sectors
sdmmc1: can't enable card
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 5.6 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell
### rev. C #############################################
U-Boot SPL 2014.04.-00015-gb4422bd (Apr 22 2014 - 13:24:28)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2014.04-00015-gb4422bd (Apr 22 2014 - 13:24:29)
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
Net: <ethaddr> not set, Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
159 bytes read in 3 ms (51.8 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
reading bsd.umg
7423360 bytes read in 418 ms (16.9 MiB/s)
## Booting kernel from Legacy Image at 82800000 ...
Image Name: boot
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7423296 Bytes = 7.1 MiB
Load Address: 80300000
Entry Point: 80300000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting Kernel ...
OpenBSD/omap booting ...
arg0 0x0 arg1 0xe05 arg2 0x80000100
atag core flags 0 pagesize 0 rootdev 0
atag cmdline [sd0i:/bsd.umg]
atag mem start 0x80000000 size 0x20000000
bootfile: sd0i:/bsd.umg
bootargs:
memory size derived from u-boot
bootconf.mem[0].address = 80000000 pages 131072/0x20000000
Allocating page tables
freestart = 0x80a15000, free_pages = 128491 (0x0001f5eb)
IRQ stack: p0x80a43000 v0xc0a43000
ABT stack: p0x80a44000 v0xc0a44000
UND stack: p0x80a45000 v0xc0a45000
SVC stack: p0x80a46000 v0xc0a46000
Creating L1 page table at 0x80a18000
Mapping kernel
Constructing L2 page tables
undefined page pmap [ using 173468 bytes of bsd ELF symbol table ]
board type: beaglebone
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6-current (RAMDISK-OMAP) #1: Thu Oct 9 20:24:32 AEDT 2014
r...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK-OMAP
real mem = 536870912 (512MB)
avail mem = 515182592 (491MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/1,4way) I-cache, 32KB(64b/1,4way) wr-back D-cache
omap0 at mainbus0: BeagleBone
prcm0 at omap0 rev 0.2
sitaracm0 at omap0: control module, rev 1.0
intc0 at omap0 rev 5.0
omap0: device edma unit 0 not configured
dmtimer0 at omap0 rev 3.1
dmtimer1 at omap0 rev 3.1
omdog0 at omap0 rev 0.1
omgpio0 at omap0: rev 0.1
omgpio1 at omap0: rev 0.1
omgpio2 at omap0: rev 0.1
omgpio3 at omap0: rev 0.1
omap0: device tiiic unit 0 not configured
omap0: device tiiic unit 1 not configured
omap0: device tiiic unit 2 not configured
ommmc0 at omap0
sdmmc0 at ommmc0
ommmc1 at ompa0
sdmmc1 at ommmc1
com0 at omap0: ti16750, 64 byte fifo
com0: console
cpsw0 at omap0: version 1.12 (0), address 1c:ba:82:d6:13:57
ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1:OUI
0x0001f0, model 0x000f
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed
sd0: 15262MB, 512 bytes/sector, 31257600 sectors
sdmmc1: can't enable card
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 5.6 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell
