I also missed that.
I’m not sure the PTP version even has sync capability, you’d have to check the spec sheet or user manual. I wouldn’t use 900 MHz for backhaul so I am not familiar with the product, other than as you say, it’s the SM hardware (and therefore I assume needs 24V power). From: AF <af-boun...@af.afmug.com> On Behalf Of Mathew Howard Sent: Thursday, June 18, 2020 4:32 PM To: AnimalFarm Microwave Users Group <af@af.afmug.com> Subject: Re: [AFMUG] PacketFlux Sync for PTP 450i 900 MHz? Oh, wait... I just realized he said *PTP* 450i... if that's the case, that changes things (that would be the same hardware, physically, as the 900mhz 450i SM). The 900mhz PMP450i SM does have the old 6 pin connector on it, but I don't remember if that's usable for sync or not.. you might need sync over power. If it is actually a PMP450i AP, then yeah, the simplest thing for a single AP is to just get the AUX port Syncbox Junior and be done with it. On Thu, Jun 18, 2020 at 4:21 PM Ken Hohhof <af...@kwisp.com <mailto:af...@kwisp.com> > wrote: AUX port is RJ45. Apparently you can make a 6pin to 8pin adapter cable following instructions in the Cambium documentation, to convert from timing port to AUX port. Syncpipes have been EOL for awhile, so I forget how many versions there were. I know there was a BASIC and a PARASITIC. I don’t remember if there was a version that could be powered directly from a timing/UGPS/AUX port. Personally, I’d spend the $130 and get the new version. Or if it’s a SyncPipe BASIC, buy a PowerInjector+CambiumSync. From: AF <af-boun...@af.afmug.com <mailto:af-boun...@af.afmug.com> > On Behalf Of Steve Jones Sent: Thursday, June 18, 2020 3:46 PM To: AnimalFarm Microwave Users Group <af@af.afmug.com <mailto:af@af.afmug.com> > Subject: Re: [AFMUG] PacketFlux Sync for PTP 450i 900 MHz? Is the aux port sync the old input? Can he just hang his old syncpipe off that directly On Thu, Jun 18, 2020, 3:41 PM Ken Hohhof <af...@kwisp.com <mailto:af...@kwisp.com> > wrote: I think that AP has an AUX port, doesn’t it? So you could use a Syncbox Junior AUX port version. https://store.packetflux.com/syncbox-junior-aux-port-version/ From: AF <af-boun...@af.afmug.com <mailto:af-boun...@af.afmug.com> > On Behalf Of cg...@graytechsoftware.com <mailto:cg...@graytechsoftware.com> Sent: Thursday, June 18, 2020 2:17 PM To: 'AnimalFarm Microwave Users Group' <af@af.afmug.com <mailto:af@af.afmug.com> > Subject: Re: [AFMUG] PacketFlux Sync for PTP 450i 900 MHz? Thank you. This is a small site with a handful of customers… and I only need sync on this one radio. Will any of the smaller units work? From: AF <af-boun...@af.afmug.com <mailto:af-boun...@af.afmug.com> > On Behalf Of Ryan Ray Sent: Thursday, June 18, 2020 2:55 PM To: AnimalFarm Microwave Users Group <af@af.afmug.com <mailto:af@af.afmug.com> > Subject: Re: [AFMUG] PacketFlux Sync for PTP 450i 900 MHz? Rackinjector you use the Power Injection for Cambium Sync Board cards. For a powerinjector you use the Powerinjector Plus Cambium-Style On Thu, Jun 18, 2020 at 11:30 AM <cg...@graytechsoftware.com <mailto:cg...@graytechsoftware.com> > wrote: I have a site where I need sync only for a PTP 450i 900 MHz AP. Any recommendation for which PacketFlux injector to use? [I have some old syncpipes, but they are not new enough.] Thank you, Chris -- AF mailing list AF@af.afmug.com <mailto:AF@af.afmug.com> http://af.afmug.com/mailman/listinfo/af_af.afmug.com -- AF mailing list AF@af.afmug.com <mailto:AF@af.afmug.com> http://af.afmug.com/mailman/listinfo/af_af.afmug.com -- AF mailing list AF@af.afmug.com <mailto:AF@af.afmug.com> http://af.afmug.com/mailman/listinfo/af_af.afmug.com
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
