Hi,
I used the file named usrp_x310_fpga_HG.bit
Nicolas
Le 27/03/2019 à 15:10, Marcus D. Leech a écrit :
On 03/27/2019 05:39 AM, Nicolas GALLAND wrote:
Hi,
after the recovery, i can't ping the device to the default address.
It gives me a "host unreachable" error when I try.
Nicolas
Which image did you select when you used Vivado to recover the device
via JTAG?
Le 26/03/2019 à 17:28, Marcus D Leech a écrit :
So it’s not clear where we are at here.
After recovery can you ping the device at the default address?
Sent from my iPhone
On Mar 25, 2019, at 12:12 PM, Joe Martin via USRP-users
<usrp-users@lists.ettus.com> wrote:
Thanks, Nicolas. I am interested to hear how you eventually clear
the problem as I also have an X310 and so far all works fine but
someday I may face the same issue as you are experiencing so please
when you find a solution please post it. I am not experienced
enough yet with mine to be able to suggest a solution for you
unfortunately. Maybe someone else can.
I (like you) am eager to hear any suggestion(s) to resolve your issue.
Regards,
Joe
On Mar 25, 2019, at 9:28 AM, Nicolas GALLAND
<nicolas.gall...@obspm.fr> wrote:
Hi,
it is indeed a typo here. I did ping 192.168.10.2 first, and then
I tried on 192.168.10.3 to see if the error message was the same.
In any case (even using ping broadcast on all the sub network my
computer is connected to) i have this message. It looks like there
is a connection between the computer and the device, since my
computer says there is no more network when I switch off the USRP.
Kind regards
Nicolas
Le 22/03/2019 à 18:52, Joe Martin a écrit :
Nicolas,
It appears you were pinging 192.168.10.3, not 192.168.10.2.
Maybe this particular example was simply a typo and you used the
correct IP address to ping during your other tests?
Regards,
Joe
On Mar 22, 2019, at 11:05 AM, Nicolas GALLAND via USRP-users
<usrp-users@lists.ettus.com> wrote:
Hello everyone,
I had some trouble with my X310 and I needed to upload my UHD
installation and consequently to update the FPGA image on the
board. After doing it through eternet port, I lost connection so
I decide to follow the recovery procedure to upload the FPGA
image using the JTAG port (following
https://kb.ettus.com/X300/X310_Device_Recovery).
The upload is fine, and the computer recognises the network with
IP address 192.168.10.1, but when I try to ping 192.168.10.2 (as
explained in the procedure) I have
PING 192.168.10.3 (192.168.10.3) 56(84) bytes of data.
From 192.168.10.1 icmp_seq=1 Destination Host Unreachable
From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
From 192.168.10.1 icmp_seq=5 Destination Host Unreachable
until I stop it. I have two x310 in the same situation, and I
tried on two different computers with different ethernet cables.
Could the hardware be broken ? (If so, isn't it strange that the
computer still sees the network ?)
Thanks a lot, and nice week end !
Kind regards,
Nicolas
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
