Hi,
after the recovery, i can't ping the device to the default address. It
gives me a "host unreachable" error when I try.
Nicolas
Le 26/03/2019 à 17:28, Marcus D Leech a écrit :
So it’s not clear where we are at here.
After recovery can you ping the device at the default address?
Sent from my iPhone
On Mar 25, 2019, at 12:12 PM, Joe Martin via USRP-users
<usrp-users@lists.ettus.com> wrote:
Thanks, Nicolas. I am interested to hear how you eventually clear the problem
as I also have an X310 and so far all works fine but someday I may face the
same issue as you are experiencing so please when you find a solution please
post it. I am not experienced enough yet with mine to be able to suggest a
solution for you unfortunately. Maybe someone else can.
I (like you) am eager to hear any suggestion(s) to resolve your issue.
Regards,
Joe
On Mar 25, 2019, at 9:28 AM, Nicolas GALLAND <nicolas.gall...@obspm.fr> wrote:
Hi,
it is indeed a typo here. I did ping 192.168.10.2 first, and then I tried on
192.168.10.3 to see if the error message was the same. In any case (even using
ping broadcast on all the sub network my computer is connected to) i have this
message. It looks like there is a connection between the computer and the
device, since my computer says there is no more network when I switch off the
USRP.
Kind regards
Nicolas
Le 22/03/2019 à 18:52, Joe Martin a écrit :
Nicolas,
It appears you were pinging 192.168.10.3, not 192.168.10.2. Maybe this
particular example was simply a typo and you used the correct IP address to
ping during your other tests?
Regards,
Joe
On Mar 22, 2019, at 11:05 AM, Nicolas GALLAND via USRP-users
<usrp-users@lists.ettus.com> wrote:
Hello everyone,
I had some trouble with my X310 and I needed to upload my UHD installation and
consequently to update the FPGA image on the board. After doing it through
eternet port, I lost connection so I decide to follow the recovery procedure to
upload the FPGA image using the JTAG port (following
https://kb.ettus.com/X300/X310_Device_Recovery).
The upload is fine, and the computer recognises the network with IP address
192.168.10.1, but when I try to ping 192.168.10.2 (as explained in the
procedure) I have
PING 192.168.10.3 (192.168.10.3) 56(84) bytes of data.
From 192.168.10.1 icmp_seq=1 Destination Host Unreachable
From 192.168.10.1 icmp_seq=2 Destination Host Unreachable
From 192.168.10.1 icmp_seq=3 Destination Host Unreachable
From 192.168.10.1 icmp_seq=4 Destination Host Unreachable
From 192.168.10.1 icmp_seq=5 Destination Host Unreachable
until I stop it. I have two x310 in the same situation, and I tried on two
different computers with different ethernet cables.
Could the hardware be broken ? (If so, isn't it strange that the computer still
sees the network ?)
Thanks a lot, and nice week end !
Kind regards,
Nicolas
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
_______________________________________________
USRP-users mailing list
USRP-users@lists.ettus.com
http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
