On 4/19/2012 1:55 AM, Timo Ketola wrote:
Gasket needs a different configuration for 10BaseT than for higher speeds.Signed-off-by: Timo Ketola<t...@exertus.fi> --- Changes in v4: - Rewrapped commit message Changes in v2: - Dropped patches 2 and 3 so this one changed from 5 to 3 - Rebased to u-boot-imx next - Removed the remove of 'miiphy_duplex' call - Changed 'speed == _100BASET' to 'speed != _10BASET' to not to break _1000BASET - Changed configuration option to put gasket into RMII mode from !CONFIG_MII to CONFIG_RMII. I'm not too sure how this should be done though. !CONFIG_MII is normally used for this but its original purpose was to enable MII *management* interface, I think... drivers/net/fec_mxc.c | 43 ++++++++++++++++++++++++------------------- 1 files changed, 24 insertions(+), 19 deletions(-) diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index 824a199..48a69d4 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -440,6 +440,22 @@ static int fec_open(struct eth_device *edev) */ writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN, &fec->eth->ecntrl); +#ifdef CONFIG_PHYLIB + if (!fec->phydev) + fec_eth_phy_config(edev); + if (fec->phydev) { + /* Start up the PHY */ + phy_startup(fec->phydev); + speed = fec->phydev->speed; + } else { + speed = _100BASET; + } +#else + miiphy_wait_aneg(edev); + speed = miiphy_speed(edev->name, fec->phy_id); + miiphy_duplex(edev->name, fec->phy_id); +#endif + #if defined(CONFIG_MX25) || defined(CONFIG_MX53) udelay(100); /* @@ -453,9 +469,14 @@ static int fec_open(struct eth_device *edev) while (readw(&fec->eth->miigsk_enr)& MIIGSK_ENR_READY) udelay(2); -#if !defined(CONFIG_MII) - /* configure gasket for RMII, 50 MHz, no loopback, and no echo */ - writew(MIIGSK_CFGR_IF_MODE_RMII,&fec->eth->miigsk_cfgr); +#if defined(CONFIG_RMII) + if (speed != _10BASET) + /* configure gasket for RMII, 50MHz, no loopback, and no echo */ + writew(MIIGSK_CFGR_IF_MODE_RMII,&fec->eth->miigsk_cfgr); + else + /* configure gasket for RMII, 5MHz, no loopback, and no echo */ + writew(MIIGSK_CFGR_IF_MODE_RMII | MIIGSK_CFGR_FRCONT, + &fec->eth->miigsk_cfgr); #else /* configure gasket for MII, no loopback, and no echo */ writew(MIIGSK_CFGR_IF_MODE_MII,&fec->eth->miigsk_cfgr); @@ -474,22 +495,6 @@ static int fec_open(struct eth_device *edev) } #endif
Can you fix 10BASET for non-reduced pin count boards as well? Thanks Troy _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
