> -----Original Message-----
> From: Valentin Longchamp [mailto:valentin.longch...@keymile.com]
> Sent: Wednesday, May 04, 2011 9:24 PM
> To: u-boot@lists.denx.de
> Cc: holger.bru...@keymile.com; Prafulla Wadaskar; Valentin Longchamp;
> Wolfgang Denk; Detlev Zundel
> Subject: [PATCH v3 8/8] arm/km: update mgcoge3un board support
>
> From: Holger Brunck <holger.bru...@keymile.com>
This line should be removed or moved to cc/ack/test list, it will appear in
commit log
>
> We change default settings for egiga on mgcoge3un.
> The reason we need this is that we have the gig port on mgcoge3un
> connected using a back-to-back pair of PHYs. There are no magnetics and
> because of that the port has to be run with a fixd configuration and
> auto-negotiation must be disabled. In the default mode the egiga driver
> uses autoneg to determine port speed - which defaults to 1G (we need
> 100M full duplex).
>
> Add wait for the GPIO line connected to mgcoge3ne before
> starting mgcoge3un. A board specific ethernet present function
> was added, because on this board ethernet is always present.
> The BOCO FPGA access was enhanced and changed to use register
> definitions.
>
> Signed-off-by: Holger Brunck <holger.bru...@keymile.com>
> Signed-off-by: Valentin Longchamp <valentin.longch...@keymile.com>
> Acked-by: Heiko Schocher <h...@denx.de>
> cc: Wolfgang Denk <w...@denx.de>
> cc: Detlev Zundel <d...@denx.de>
> cc: Prafulla Wadaskar <prafu...@marvell.com>
> ---
> Changes for v2:
> - split up first large patch series to three independent smaller
> patch series
> Changes for v3:
> - taken Prafulla's comments into account, merged with previous 08/08
> patch
>
> board/keymile/km_arm/km_arm.c | 80 +++++++++++++++++++++++++++++++++-
> ------
> include/configs/mgcoge3un.h | 25 +++++++++++++
> 2 files changed, 91 insertions(+), 14 deletions(-)
>
> diff --git a/board/keymile/km_arm/km_arm.c
> b/board/keymile/km_arm/km_arm.c
> index 4049a4e..d86acc9 100644
> --- a/board/keymile/km_arm/km_arm.c
> +++ b/board/keymile/km_arm/km_arm.c
> @@ -41,6 +41,16 @@
>
> DECLARE_GLOBAL_DATA_PTR;
>
> +/*
> + * BOCO FPGA definitions
> + */
> +#define BOCO 0x10
> +#define REG_CTRL_H 0x02
> +#define MASK_WRL_UNITRUN 0x01
> +#define MASK_RBX_PGY_PRESENT 0x40
> +#define REG_IRQ_CIRQ2 0x2d
> +#define MASK_RBI_DEFECT_16 0x01
> +
> /* Multi-Purpose Pins Functionality configuration */
> u32 kwmpp_config[] = {
> MPP0_NF_IO2,
> @@ -102,43 +112,64 @@ u32 kwmpp_config[] = {
> 0
> };
>
> +#if defined(CONFIG_MGCOGE3UN)
> +/*
> + * Wait for startup OK from mgcoge3ne
> + */
> +int startup_allowed(void)
> +{
> + unsigned char buf;
> +
> + /*
> + * Read CIRQ16 bit (bit 0)
> + */
> + if (i2c_read(BOCO, REG_IRQ_CIRQ2, 1, &buf, 1) != 0)
> + printf("%s: Error reading Boco\n", __func__);
> + else
> + if ((buf & MASK_RBI_DEFECT_16) == MASK_RBI_DEFECT_16)
> + return 1;
> + return 0;
> +}
> +
> +/*
> + * mgcoge3un has always ethernet present. Its connected to the 6061
> switch
> + * and provides ICNev and piggy4 connections.
> + */
> +int ethernet_present(void)
> +{
> + return 1;
> +}
> +#else
> int ethernet_present(void)
> {
> uchar buf;
> int ret = 0;
>
> - if (i2c_read(0x10, 2, 1, &buf, 1) != 0) {
> + if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
> printf("%s: Error reading Boco\n", __func__);
> return -1;
> }
> - if ((buf & 0x40) == 0x40)
> + if ((buf & MASK_RBX_PGY_PRESENT) == MASK_RBX_PGY_PRESENT)
You can #if here instead of as done above, it will help to reduce code size and
will be more readable.
I am sorry if I missed this in the earlier post.
> ret = 1;
>
> return ret;
> }
> +#endif
>
> int initialize_unit_leds(void)
> {
> /*
> - * init the unit LEDs
> - * per default they all are
> + * Init the unit LEDs per default they all are
> * ok apart from bootstat
> - * LED connected through BOCO
> - * BOCO lies at the address 0x10
> - * LEDs are in the block CTRL_H (addr 0x02)
> - * BOOTSTAT LED is the first 0x01
> */
> - #define BOCO 0x10
> - #define CTRL_H 0x02
> - #define APPLEDMASK 0x01
> uchar buf;
>
> - if (i2c_read(BOCO, CTRL_H, 1, &buf, 1) != 0) {
> + if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
> printf("%s: Error reading Boco\n", __func__);
> return -1;
> }
> - buf |= APPLEDMASK;
> - if (i2c_write(BOCO, CTRL_H, 1, &buf, 1) != 0) {
> + buf |= MASK_WRL_UNITRUN;
> + if (i2c_write(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
> printf("%s: Error writing Boco\n", __func__);
> return -1;
> }
> @@ -167,6 +198,27 @@ int misc_init_r(void)
> printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
> gd->bd->bi_arch_number = mach_type;
> }
> +#if defined(CONFIG_MGCOGE3UN)
> + char *wait_for_ne;
> + wait_for_ne = getenv("waitforne");
> + if (wait_for_ne != NULL) {
> + if (strcmp(wait_for_ne, "true") == 0) {
> + int cnt = 0;
> + puts("NE go: ");
> + while (startup_allowed() == 0) {
> + udelay(200000);
> + cnt++;
> + if (cnt == 5)
> + puts("wait\b\b\b\b");
> + if (cnt == 10) {
> + cnt = 0;
> + puts(" \b\b\b\b");
> + }
> + }
> + puts("OK\n");
> + }
> + }
> +#endif
>
> initialize_unit_leds();
> set_km_env();
> diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h
> index 1c32085..d022c4f 100644
> --- a/include/configs/mgcoge3un.h
> +++ b/include/configs/mgcoge3un.h
> @@ -50,4 +50,29 @@
> /* we use a new RAM type on mgcoge3un board */
> #define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-
> memphis.cfg
>
> +/*
> + * mgcoge3un has a fixed link to the marvell switch
> + * with 100MB full duplex and autoneg off, for this
> + * reason we have to change the default settings
> + */
> +#define PORT_SERIAL_CONTROL_VALUE ( \
> + MVGBE_FORCE_LINK_PASS | \
> + MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
> + MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
> + MVGBE_ADV_NO_FLOW_CTRL | \
> + MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
> + MVGBE_FORCE_BP_MODE_NO_JAM | \
> + (1 << 9) /* Reserved bit has to be 1 */ | \
> + MVGBE_DO_NOT_FORCE_LINK_FAIL | \
> + MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
> + MVGBE_DTE_ADV_0 | \
> + MVGBE_MIIPHY_MAC_MODE | \
> + MVGBE_AUTO_NEG_NO_CHANGE | \
> + MVGBE_MAX_RX_PACKET_1552BYTE | \
> + MVGBE_CLR_EXT_LOOPBACK | \
> + MVGBE_SET_FULL_DUPLEX_MODE | \
> + MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
> + MVGBE_SET_GMII_SPEED_TO_10_100 |\
> + MVGBE_SET_MII_SPEED_TO_100)
> +
> #endif /* _CONFIG_MGCOGE3UN_H */
> --
> 1.7.0.5
Regards..
Prafulla . .
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
