Hi all
On 01/14/2011 07:33 PM, Fabio Estevam wrote:
> Hi Stefano,
>
> On 1/13/2011 11:38 AM, Stefano Babic wrote:
>> On 01/12/2011 01:49 PM, Fabio Estevam wrote:
>>> Hi,
>>
>> Hi Fabio,
>>
>>>
>>> I am trying to make the new relocation scheme to work on the mx31pdk board.
>>>
>>> With this patch applied the mx31pdk build works, but not able to get a
>>> U-boot prompt yet.
>>
>> I have tried to imagine some issues, but I cannot find a clear reason.
>> Building with your patch I checked that nand_spl is still less than 2KB
>> code, and that matches the NAND page, as required by i.MX31 - so it is
>> not a problem.
>>
>> Have you tried to disable the relocation, just to check if the
>> relocation is an issue with CONFIG_SKIP_RELOCATE_UBOOT ? This is not a
>> solution, but only to check what happens.
I've done some testing now and ended up comparing start.S for ARM1136 with
ARM926EJS since
the latter is used on the Karo TX25 board which seems to have been updated and
also boots from NAND.
The result is that applying the following patch on top of Fabios patch makes
the i.MX31 PDK
boot from NAND. Booting Linux from TFTP works nicely. However the first few
lines of output
from U-boot is missing, only the "NAND: 256 MB" line is shown. I haven't tried
to understand
how booting works nowadays and why these changes work, perhaps someone with
more insight
in the mechanisms can figure out the correct assembler code.
I have no idea if this breaks other boards but at least it's start for further
work. I tried
it on the imx31 litekit (which boots from NOR) but that board doesn't seem to
boot even before applying Fabios patch,
I'll see if I can figure out why that board is broken now. Don't know when
though.
Regards, Magnus Lilja
diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S
index 12545c2..7d75ecf 100644
--- a/arch/arm/cpu/arm1136/start.S
+++ b/arch/arm/cpu/arm1136/start.S
@@ -163,6 +163,9 @@ call_board_init_f:
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
ldr r0,=0x00000000
+#if 1
+ bl board_init_f
+#else
#ifdef CONFIG_NAND_SPL
bl nand_boot
#else
@@ -172,6 +175,7 @@ call_board_init_f:
bl board_init_f
#endif /* CONFIG_ONENAND_IPL */
#endif /* CONFIG_NAND_SPL */
+#endif
/*------------------------------------------------------------------------------*/
@@ -266,11 +270,19 @@ clbss_l:str r2, [r0] /* clear
loop... */
* initialization, now running from RAM.
*/
#ifdef CONFIG_NAND_SPL
+#if 1
+ ldr r0, _nand_boot_ofs
+ mov pc, r0
+
+_nand_boot_ofs:
+ .word nand_boot
+#else
ldr r0, _nand_boot_ofs
adr r1, _start
add pc, r0, r1
_nand_boot_ofs:
.word nand_boot - _start
+#endif
#else
jump_2_ram:
ldr r0, _board_init_r_ofs
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
