On Wed, Apr 13, 2022 at 10:21 AM Michael Nazzareno Trimarchi
<mich...@amarulasolutions.com> wrote:
>
> Hi
>
> On Wed, Apr 13, 2022 at 6:09 PM Tim Harvey <thar...@gateworks.com> wrote:
> >
> > On Wed, Apr 13, 2022 at 8:56 AM Michael Nazzareno Trimarchi
> > <mich...@amarulasolutions.com> wrote:
> > >
> > > Hi Tim
> > >
> > > On Wed, Apr 13, 2022 at 5:47 PM Tim Harvey <thar...@gateworks.com> wrote:
> > > >
> > > > Enable DM_SERIAL.
> > > >
> > > > Signed-off-by: Tim Harvey <thar...@gateworks.com>
> > > > ---
> > > > v2: rebase on imx/master
> > > > ---
> > > > configs/imx8mm_venice_defconfig | 2 ++
> > > > configs/imx8mn_venice_defconfig | 2 ++
> > > > 2 files changed, 4 insertions(+)
> > > >
> > > > diff --git a/configs/imx8mm_venice_defconfig
> > > > b/configs/imx8mm_venice_defconfig
> > > > index dd61ec9b70fb..09f7d8a58ca7 100644
> > > > --- a/configs/imx8mm_venice_defconfig
> > > > +++ b/configs/imx8mm_venice_defconfig
> > > > @@ -110,6 +110,8 @@ CONFIG_SPL_DM_PMIC_MP5416=y
> > > > CONFIG_DM_REGULATOR=y
> > > > CONFIG_DM_REGULATOR_FIXED=y
> > > > CONFIG_DM_REGULATOR_GPIO=y
> > > > +CONFIG_DM_SERIAL=y
> > > > +# CONFIG_SPL_DM_SERIAL is not set
> > > > CONFIG_MXC_UART=y
> > > > CONFIG_SYSRESET=y
> > > > CONFIG_SPL_SYSRESET=y
> > > > diff --git a/configs/imx8mn_venice_defconfig
> > > > b/configs/imx8mn_venice_defconfig
> > > > index c3a96a378553..41898da4aecf 100644
> > > > --- a/configs/imx8mn_venice_defconfig
> > > > +++ b/configs/imx8mn_venice_defconfig
> > > > @@ -108,6 +108,8 @@ CONFIG_SPL_DM_PMIC_MP5416=y
> > > > CONFIG_DM_REGULATOR=y
> > > > CONFIG_DM_REGULATOR_FIXED=y
> > > > CONFIG_DM_REGULATOR_GPIO=y
> > > > +CONFIG_DM_SERIAL=y
> > > > +# CONFIG_SPL_DM_SERIAL is not set
> > > > CONFIG_MXC_UART=y
> > > > CONFIG_SYSRESET=y
> > > > CONFIG_SPL_SYSRESET=y
> > > > --
> > > > 2.17.1
> > > >
> > >
> > > Should not select in your board kconfig?
> > >
> >
> > Michael,
> >
> > I don't think it really matters. The other conversions to DM_SERIAL
> > are going in defconfigs as well.
>
> Do we know why without # CONFIG_SPL_DM_SERIAL is not set
>
> board hang?
>
Michael,
yes, if I also enable CONFIG_SPL_DM_SERIAL I get no serial output and
the board hangs even if I add 'u-boot,dm-pre-proper' to
uart2/pinctrl_uart2 nodes.
The requirement is to use DM_SERIAL in U-Boot, not in the SPL. I'm
doing the same as was done for imx8mn-evk in ff1c7961d813 ("ARM: imx:
imx8mn-evk: enable DM_SERIAL").
Thus far, no ARCH_IMX8M boards have enabled CONFIG_SPL_DM_SERIAL so I
suppose others have run into this as well but again the requirement is
to enable CONFIG_DM_SERIAL not necessarily the SPL.
Best Regards,
Tim
