On 7/29/19 6:05 PM, Adam Ford wrote: > On Mon, Jul 29, 2019 at 9:38 AM Marek Vasut <ma...@denx.de> wrote: >> >> On 7/29/19 3:19 PM, Adam Ford wrote: >>> On Mon, Jul 29, 2019 at 7:30 AM Marek Vasut <ma...@denx.de> wrote: >>>> >>>> On 7/29/19 2:16 PM, Adam Ford wrote: >>>>> On Sun, Jun 30, 2019 at 5:21 PM Adam Ford <aford...@gmail.com> wrote: >>>>>> >>>>>> The omap3.dtsi file shows the usbhshost node with two sub-nodes >>>>>> for ohci and ehci. This patch file creates the usbhshost, and >>>>>> pulls the portX-mode information. It then locates the EHCI >>>>>> sub-node, and initializes the EHCI controller with the info >>>>>> pulled from the usbhshost node. >>>>>> >>>>>> There is still more to do since there isn't an actual link >>>>>> between the 'phys' reference and the corresponding phy driver, >>>>>> and there is no nop-xceiv driver yet. >>>>>> >>>>>> In the meantime, the older style reference to >>>>>> CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull >>>>>> the phy out of reset until the phy driver is completed and the >>>>>> phandle reference is made. >>>>>> >>>>>> Signed-off-by: Adam Ford <aford...@gmail.com> >>>>>> >>>>> >>>>> Marek, >>>>> >>>>> Some subsequent patches that were depending on this have been applied >>>>> already, but they cannot be really useful until this patch is applied. >>>>> Is there any chance it can be applied? It will give some of the OMAP3 >>>>> boards the USB EHCI functionality which has been lost for a little >>>>> while. >>>> >>>> Sure, I am kinda busy and don't have enough free time to cope with this. >>>> Moreover, u-boot-usb/master fails to build: >>>> https://travis-ci.org/marex/u-boot-usb/builds/563567738 >>>> >>>> Can you take a look whether it's this patchset that causes it ? >>> >>> Marek, >>> >>> I looked at the Travis logs, and it looks like the da850evm_nand and >>> da850evm_direct_nor were failing, so I tried to clone >>> git clone --depth=50 --branch=master >>> https://github.com/marex/u-boot-usb.git marex/u-boot-usb based on line >>> 846 of the Travis log. >>> >>> When I built da850evm_nand and da850evm_direct_nor, I could not >>> replicate either the build error. >> >> I see, strange, I can replicate the error. >> >> $ make da850evm_nand_defconfig ; make -j9 >> ... >> drivers/usb/host/ohci-hcd.c: In function ‘usb_lowlevel_init’: >> drivers/usb/host/ohci-hcd.c:2056:35: error: >> ‘CONFIG_SYS_USB_OHCI_REGS_BASE’ undeclared (first use in this function); >> did you mean ‘CONFIG_SYS_USB_OHCI_CPU_INIT’? >> gohci.regs = (struct ohci_regs *)CONFIG_SYS_USB_OHCI_REGS_BASE; >> ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >> CONFIG_SYS_USB_OHCI_CPU_INIT >> drivers/usb/host/ohci-hcd.c:2056:35: note: each undeclared identifier is >> reported only once for each function it appears in >> LD drivers/usb/musb-new/built-in.o >> drivers/usb/host/ohci-hcd.c:2060:20: error: >> ‘CONFIG_SYS_USB_OHCI_SLOT_NAME’ undeclared (first use in this function); >> did you mean ‘CONFIG_SYS_USB_OHCI_CPU_INIT’? >> gohci.slot_name = CONFIG_SYS_USB_OHCI_SLOT_NAME; >> ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >> CONFIG_SYS_USB_OHCI_CPU_INIT >> LD drivers/mtd/spi/spi-nor.o >> make[1]: *** [scripts/Makefile.build:279: drivers/usb/host/ohci-hcd.o] >> Error 1 >> make: *** [Makefile:1594: drivers/usb/host] Error 2 >> make: *** Waiting for unfinished jobs.... >> > > aford@aford-OptiPlex-7050:~/src/marex/u-boot-usb$ make da850evm_nand_defconfig > HOSTCC scripts/basic/fixdep > HOSTCC scripts/kconfig/conf.o > YACC scripts/kconfig/zconf.tab.c > LEX scripts/kconfig/zconf.lex.c > HOSTCC scripts/kconfig/zconf.tab.o > HOSTLD scripts/kconfig/conf > # > # configuration written to .config > # > aford@aford-OptiPlex-7050:~/src/marex/u-boot-usb$ make ARCH=arm > CROSS_COMPILE="arm-linux-" -j8 > scripts/kconfig/conf --syncconfig Kconfig > CHK include/config.h
Are you sure you're building the correct tree ? The current top commit is 9812437f976c025775ddd36eede30605d0607ba8 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
