On Fri, Mar 8, 2019 at 6:34 PM Jagan Teki <ja...@amarulasolutions.com> wrote: > > On Fri, Mar 8, 2019 at 11:32 PM Peter Robinson <pbrobin...@gmail.com> wrote: > > > > Hey Tom and Jagan, > > > > > Hey all, > > > > > > So it's release day and I've put up v2019.04-rc3, I've updated git and > > > the tarballs are also up now. > > > > > > Thanks again to having signed tags, between -rc2 and -rc3 we have a good > > > changelog under 'git log --merges v2019.04-rc2..v2019.04-rc3' > > > > > > We're looking at release on April 8th, 2019. > > > > I've had reports of crashes on AllWinner A20 devices, at least > > Cubieboard2, CubieTruck and BananaPi, with rc2/rc3 (I'm not 100% sure > > when it started) in Fedora. I'm suspecting some of the DM migration > > here. > > > > Are either of you aware of any issues there? > > > > Crash below. > > > > Regards, > > Peter > > > > U-Boot SPL 2019.04-rc3 (Mar 05 2019 - 14:49:53 +0000) > > DRAM: 2048 MiB > > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > > Trying to boot from MMC1 > > > > > > U-Boot 2019.04-rc3 (Mar 05 2019 - 14:49:53 +0000) Allwinner Technology > > > > CPU: Allwinner A20 (SUN7I) > > Model: Cubietech Cubietruck > > I2C: ready > > DRAM: 2 GiB > > MMC: mmc@1c0f000: 0, mmc@1c12000: 1 > > Loading Environment from FAT... ** No valid partitions found ** > > Setting up a 1024x768 vga console (overscan 0x0) > > In: serial > > Out: vga > > Err: vga > > Allwinner mUSB OTG (Peripheral) > > SCSI: Target spinup took 0 ms. > > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > > flags: ncq stag pm led clo only pmp pio slum part ccc apst > > > > Net: sunxi_set_gate: (CLK#66) unhandled > > eth0: ethernet@1c50000 > > Warning: usb_ether using MAC address from ROM > > , eth1: usb_ether > > starting USB... > > USB0: USB EHCI 1.00 > > USB1: USB OHCI 1.0 > > USB2: USB EHCI 1.00 > > USB3: USB OHCI 1.0 > > scanning bus 0 for devices... 1 USB Device(s) found > > scanning bus 1 for devices... 1 USB Device(s) found > > scanning bus 2 for devices... 1 USB Device(s) found > > scanning bus 3 for devices... 1 USB Device(s) found > > scanning usb for storage devices... 0 Storage Device(s) found > > Hit any key to stop autoboot: 0 > > switch to partitions #0, OK > > mmc0 is current device > > ** Invalid partition 1 ** > > are you sure, your sd has partitions? > > Can you switch mmc dev and check the contents, mean while I can try it > on A20 later tomorrow.
these devices boot with the version we shipped with F-29, which was 2018.09 and the users report if they reflash back to that version it works. Peter _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot