Hi Kever, On Mon, 7 Jan 2019 at 23:38, Kever Yang <kever.y...@rock-chips.com> wrote: > > Hi Simon, > > > On 01/08/2019 08:38 AM, Simon Glass wrote: > > Hi Mark, > > > > On Sat, 5 Jan 2019 at 09:05, Mark Kettenis <mark.kette...@xs4all.nl> wrote: > >>> From: Simon Glass <s...@chromium.org> > >>> Date: Sat, 5 Jan 2019 08:56:07 -0700 > >>> > >>> Hi Mark, > >>> > >>> On Fri, 4 Jan 2019 at 20:35, Simon Glass <s...@chromium.org> wrote: > >>>> Hi Mark, > >>>> > >>>> On Fri, 4 Jan 2019 at 13:43, Simon Glass <s...@chromium.org> wrote: > >>>>> Hi Mark, > >>>>> > >>>>> On Fri, 4 Jan 2019 at 13:29, Mark Kettenis <mark.kette...@xs4all.nl> > >>>>> wrote: > >>>>>>> From: Simon Glass <s...@chromium.org> > >>>>>>> Date: Fri, 4 Jan 2019 13:12:58 -0700 > >>>>>>> > >>>>>>> Hi Mark, > >>>>>>> > >>>>>>> On Fri, 4 Jan 2019 at 12:43, Mark Kettenis <mark.kette...@xs4all.nl> > >>>>>>> wrote: > >>>>>>>> So obviously that diff is needed to boot properly from uSD. I'll > >>>>>>>> send > >>>>>>>> out a git patch with a proper commit messages in a bit. > >>>>>>> Yes I have the diff. What toolchain version are you using? > >>>>>> I'm using the following OpenBSD packages: > >>>>>> > >>>>>> aarch64-none-elf-binutils-2.27p0 > >>>>>> aarch64-none-elf-gcc-linaro-6.3.2017.02p3 > >>>>>> > >>>>>> which is binutils 2.27 and the Linaro GCC 6.3.2017.02 with minimal > >>>>>> patches to get them to build on OpenBSD. > >>>>> OK thank you. I'll try again when I get back. Something funny is going > >>>>> on. > >>>> I pushed my tree to u-boot-dm/rk-working > >>>> > >>>> export ARCH=arm > >>>> CROSS_COMPILE=/opt/linaro/gcc-linaro-6.3.1-2017.02-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu- > >>>> O=/tmp/b/firefly-rk3399 > >>>> > >>>> /tmp/b/firefly-rk3399> ln -s > >>>> ~/cosarm/arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf > >>>> > >>>> make -s firefly-rk3399_defconfig && make -s -j16 && make -s u-boot.itb > >>>> && /tmp/b/firefly-rk3399/tools/mkimage -n rk3399 -T rksd -d > >>>> /tmp/b/firefly-rk3399/spl/u-boot-spl.bin idbspl.img && sudo dd > >>>> if=idbspl.img of=/dev/sdb seek=64 && sudo dd > >>>> if=/tmp/b/firefly-rk3399/u-boot.itb of=/dev/sdb seek=16384 && sync > >>>> > >>>> Output is > >>>> > >>>> U-Boot SPL board init > >>>> abc.d123456 7fe90 > >>>> > >>>> at which point it hangs. > >>>> > >>>> Hopefully I've done something silly in the setup. Any chance you could > >>>> share your image? > >>>> > >>>> Thanks for your help. I am sure I had the board running at one point. > >>> Thanks for the image - I tried it with the same result. I think my > >>> board is 4GB - perhaps there is a memory init problem still? > >> Not inconceivable. My board indeed only has 2GB. > > OK thanks. Oddly I got this running on Bob which also has 4GB and did > > not have this problem. > > For 4GB ddr3, maybe you need to use > arch/arm/dts/rk3399-sdram-ddr3-4G-1600.dtsi, > and you can turn on DEBUG so that we can confirm if hang in dram init > driver.
OK thank you, will try. It really should select the correct one automatically. BTW your email came through as a new one, not a reply to the original. Is there something wrong with you config? Regards, Simon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
