Hi Mark, On Sat, 5 Jan 2019 at 09:05, Mark Kettenis <mark.kette...@xs4all.nl> wrote: > > > From: Simon Glass <s...@chromium.org> > > Date: Sat, 5 Jan 2019 08:56:07 -0700 > > > > Hi Mark, > > > > On Fri, 4 Jan 2019 at 20:35, Simon Glass <s...@chromium.org> wrote: > > > > > > Hi Mark, > > > > > > On Fri, 4 Jan 2019 at 13:43, Simon Glass <s...@chromium.org> wrote: > > > > > > > > Hi Mark, > > > > > > > > On Fri, 4 Jan 2019 at 13:29, Mark Kettenis <mark.kette...@xs4all.nl> > > > > wrote: > > > > > > > > > > > From: Simon Glass <s...@chromium.org> > > > > > > Date: Fri, 4 Jan 2019 13:12:58 -0700 > > > > > > > > > > > > Hi Mark, > > > > > > > > > > > > On Fri, 4 Jan 2019 at 12:43, Mark Kettenis > > > > > > <mark.kette...@xs4all.nl> wrote: > > > > > > > So obviously that diff is needed to boot properly from uSD. I'll > > > > > > > send > > > > > > > out a git patch with a proper commit messages in a bit. > > > > > > > > > > > > Yes I have the diff. What toolchain version are you using? > > > > > > > > > > I'm using the following OpenBSD packages: > > > > > > > > > > aarch64-none-elf-binutils-2.27p0 > > > > > aarch64-none-elf-gcc-linaro-6.3.2017.02p3 > > > > > > > > > > which is binutils 2.27 and the Linaro GCC 6.3.2017.02 with minimal > > > > > patches to get them to build on OpenBSD. > > > > > > > > OK thank you. I'll try again when I get back. Something funny is going > > > > on. > > > > > > I pushed my tree to u-boot-dm/rk-working > > > > > > export ARCH=arm > > > CROSS_COMPILE=/opt/linaro/gcc-linaro-6.3.1-2017.02-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu- > > > O=/tmp/b/firefly-rk3399 > > > > > > /tmp/b/firefly-rk3399> ln -s > > > ~/cosarm/arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf > > > > > > make -s firefly-rk3399_defconfig && make -s -j16 && make -s u-boot.itb > > > && /tmp/b/firefly-rk3399/tools/mkimage -n rk3399 -T rksd -d > > > /tmp/b/firefly-rk3399/spl/u-boot-spl.bin idbspl.img && sudo dd > > > if=idbspl.img of=/dev/sdb seek=64 && sudo dd > > > if=/tmp/b/firefly-rk3399/u-boot.itb of=/dev/sdb seek=16384 && sync > > > > > > Output is > > > > > > U-Boot SPL board init > > > abc.d123456 7fe90 > > > > > > at which point it hangs. > > > > > > Hopefully I've done something silly in the setup. Any chance you could > > > share your image? > > > > > > Thanks for your help. I am sure I had the board running at one point. > > > > Thanks for the image - I tried it with the same result. I think my > > board is 4GB - perhaps there is a memory init problem still? > > Not inconceivable. My board indeed only has 2GB.
OK thanks. Oddly I got this running on Bob which also has 4GB and did not have this problem. Regards, Simon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
