Hi Simon,
On 01/08/2019 08:38 AM, Simon Glass wrote: > Hi Mark, > > On Sat, 5 Jan 2019 at 09:05, Mark Kettenis <mark.kette...@xs4all.nl> wrote: >>> From: Simon Glass <s...@chromium.org> >>> Date: Sat, 5 Jan 2019 08:56:07 -0700 >>> >>> Hi Mark, >>> >>> On Fri, 4 Jan 2019 at 20:35, Simon Glass <s...@chromium.org> wrote: >>>> Hi Mark, >>>> >>>> On Fri, 4 Jan 2019 at 13:43, Simon Glass <s...@chromium.org> wrote: >>>>> Hi Mark, >>>>> >>>>> On Fri, 4 Jan 2019 at 13:29, Mark Kettenis <mark.kette...@xs4all.nl> >>>>> wrote: >>>>>>> From: Simon Glass <s...@chromium.org> >>>>>>> Date: Fri, 4 Jan 2019 13:12:58 -0700 >>>>>>> >>>>>>> Hi Mark, >>>>>>> >>>>>>> On Fri, 4 Jan 2019 at 12:43, Mark Kettenis <mark.kette...@xs4all.nl> >>>>>>> wrote: >>>>>>>> So obviously that diff is needed to boot properly from uSD. I'll send >>>>>>>> out a git patch with a proper commit messages in a bit. >>>>>>> Yes I have the diff. What toolchain version are you using? >>>>>> I'm using the following OpenBSD packages: >>>>>> >>>>>> aarch64-none-elf-binutils-2.27p0 >>>>>> aarch64-none-elf-gcc-linaro-6.3.2017.02p3 >>>>>> >>>>>> which is binutils 2.27 and the Linaro GCC 6.3.2017.02 with minimal >>>>>> patches to get them to build on OpenBSD. >>>>> OK thank you. I'll try again when I get back. Something funny is going on. >>>> I pushed my tree to u-boot-dm/rk-working >>>> >>>> export ARCH=arm >>>> CROSS_COMPILE=/opt/linaro/gcc-linaro-6.3.1-2017.02-x86_64_aarch64-linux-gnu/bin/aarch64-linux-gnu- >>>> O=/tmp/b/firefly-rk3399 >>>> >>>> /tmp/b/firefly-rk3399> ln -s >>>> ~/cosarm/arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf >>>> >>>> make -s firefly-rk3399_defconfig && make -s -j16 && make -s u-boot.itb >>>> && /tmp/b/firefly-rk3399/tools/mkimage -n rk3399 -T rksd -d >>>> /tmp/b/firefly-rk3399/spl/u-boot-spl.bin idbspl.img && sudo dd >>>> if=idbspl.img of=/dev/sdb seek=64 && sudo dd >>>> if=/tmp/b/firefly-rk3399/u-boot.itb of=/dev/sdb seek=16384 && sync >>>> >>>> Output is >>>> >>>> U-Boot SPL board init >>>> abc.d123456 7fe90 >>>> >>>> at which point it hangs. >>>> >>>> Hopefully I've done something silly in the setup. Any chance you could >>>> share your image? >>>> >>>> Thanks for your help. I am sure I had the board running at one point. >>> Thanks for the image - I tried it with the same result. I think my >>> board is 4GB - perhaps there is a memory init problem still? >> Not inconceivable. My board indeed only has 2GB. > OK thanks. Oddly I got this running on Bob which also has 4GB and did > not have this problem. For 4GB ddr3, maybe you need to use arch/arm/dts/rk3399-sdram-ddr3-4G-1600.dtsi, and you can turn on DEBUG so that we can confirm if hang in dram init driver. Thanks, - Kever > Regards, > Simon > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
